Multi-Tech Systems MVP103, 410 manual Remote Configuration

Page 67

Chapter 4 - Miscellaneous

Remote Configuration

Remote configuration provides procedures for viewing or changing the configuration of a remote MultiVOIP. Remote configuration requires the MultiVOIP software to be loaded on the local PC. The local PC then controls the remote MultiVOIP.

To accomplish this, a MT5634ZBA modem is included with your MultiVOIP, except on models MVP130-AV and MVP130-AV-FXS. Two serial cables are also included, the DB25 male to RJ45 cable is used with the MultiVOIP (MVP210 model) or the DB25 male to DB25 male (larger connectors) is used with the MultiVOIP (MVP410 and MVP 810 models).

Note: On some MVP410 and MVP810 models, the modem is built in. On these models, connect the dial-up line to the RJ11 modular connector labeled Command Modem.

To remotely configure a MultiVOIP, a local PC needs to be connected to a dial-up line and the MultiVOIP software configured to call the remote MultiVOIP. The remote MultiVOIP needs to have the MT5634ZBA modem connected to a dial-up line and the Command Port. Once the connection to the remote unit is made, you can change the configuration as required. Once the configuration is changed, you can download the new configuration to the remote MultiVOIP.

1.At the remote site, verify that the “Console Messages” in the Configuration Logs dialog box is disabled before you power down the remote MultiVOIP.

2.At the remote site, remove the serial cable from the PC to the Command Port connector on the back panel of the MultiVOIP.

3.At the remote site, connect one of the serial cables provided from the Command Port connector on the back panel of the MultiVOIP to the RS-232 connector on the modem.

3a. Connect the modem to your local telephone line.

3b. Provide your telephone number to the person verifying your configuration.

3c. Power On the modem first to allow it to initialize. Then power On the MultiVOIP.

4.At the main site, connect your local PC to a modem that is connected to a dial-up line.

5.Install the MultiVOIP software on the local PC. When installed, click StartProgramsMultiVOIP 9.06.XXConfiguration Port Setup.

6.The Comm Port Setup dialog box displays.

Verify that the Select Port box is set for the COM port of your local PC and that the Baud Rate is set to 115200.

In Modem Setup, the modem Initialization String, Initialization Response, and Connect Response should be configured as shown in the above dialog box.

Multi-Tech Systems, Inc. Avaya Communication Manager Guide

67

Page 66 Page 68
Image 67
Page 66 Page 68
Contents MultiVOIP Revision Date Description Configuration GuideContents Introduction IntroductionMultiVOIP in Avaya Communication Manager System Configuration ConfigurationChannel RTP Port Rtcp Port T38 Port Configuration Configuration Bandwidth per Channel Voice Frames per IP Packet Communication Manager MultiVOIP FXS Channels Configuration Configuration Communication Manager MultiVOIP FXO Channels Configuration = Isdn Communication Manager MultiVOIP did Channels Configuration = Isdn Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Regional Parameter Definitions Field Name Values Description Regional Parameters screenField Name Values Description Regional Parameter DefinitionsTone Pair Values Related MultiVOIP Setup Parameters Communication Manager SettingsRelated MultiVOIP Setup Parameters Version 4 Parameters Voice/Fax Parameters Channel to be configured is selected here Mode Fax FRF 11 T.38 Fax EnableFax Volume Jitter Value Default =Advanced Features Jitter Automatic Auto DisconnectInterface Parameters Related MultiVOIP Setup Parameters FXS Not applicable to FXS interface Dialing Options FXO Interface Parameter DefinitionsFXO Disconnect On cont’d CID Number Voip Caller ID Case #4 Remote FXS call on H.323 voip system Did Options Policy GK General SettingsGK General Settings Definitions Activity ConfigurationRAS Parameters GK General Settings Definitions cont’dGatekeeper Endpoints Command Buttons ID alias of the endpoint originating the call Gatekeeper CallsCurrent Calls Field Definitions Number. a sequential number for identification in the listID identifies the call with which the message is associated Call Details Field DefinitionsConference ID number CID is a unique non-zero value created Conference will have the same CIDReason associated with the last state of the call Total amount of bandwidth used by the callType of conference request create, invite or join Last reported state of the callAddress and port number H.323 alias name used to make the callE164 alias phone number used to make the call An e-mail address used to make the callOptions Gatekeeper Network ParametersNetwork Parameter Definitions Field Name Values Description Status InformationLine Hunting Information ARQCall Mode GK-ID Public Gatekeeper ServicesServices Screen Definitions Field Name Values Description GK Defined ServicesDynamic Miscellaneous MiscellaneousComm Mgr Dialing Example #1 a local station-to-station call Remote Configuration Miscellaneous MVP210-AV Rev a MVP130-AV RevMVP130-AV Rev a MVP130-AV-FXS Rev aMiscellaneous Link Management Feature Issues Index IndexCoder field FRF11 Gatekeeper Response to field GK General Settings, RAS DID-DPO FXO Trunk Group form fields to set Dtmf Gain Unregister endpoints command Dtmf Gain High Tones
Top Page Image Contents