Panasonic KX-TG1840NZ Troubleshooting, Initial settings, Problem Cause & solution

Page 54

Useful Information

Troubleshooting

If you still have difficulties after following the instructions in this section, disconnect the AC adaptor and turn off the handset, then reconnect the AC adaptor and turn on the handset.

Initial settings

Problem	Cause & solution
w is flashing.	LThe handset is not registered to the base unit.
	Register it (page 46).
	LThe handset is too far from the base unit. Move
	closer.
	LThe AC adaptor is not connected. Check the
	connections.
	LYou are using the handset or base unit in an area
	with high electrical interference. Locate the handset
	and base unit away from interference sources, such
	as antenna and mobile phones.

The handset display is blank.	LThe handset is not turned on. Turn the power on
	(page 11).

The handset will not turn on.	LMake sure that the batteries are installed correctly
	(page 10).
	LFully charge the batteries (page 10).
	LClean the charge contact and charge again (page
	10).

Image 54

Contents Model No. KX-TG1840NZ Introduction Feature highlights Useful Information Accessory information Included accessoriesAdditional/replacement accessories General Battery cautionImportant information EnvironmentControls and displays ControlsDisplays Connections Base unit display iconsBattery installation Battery chargeBattery strength Battery icon Battery replacement Turning the power on/offSetting the date and time Example 330 PM Making calls using the handset Redial featureTo erase numbers in the redial list Other featuresVoice enhancer Handset phonebook Key lockPause button for PBX/long distance service users Making calls using the base unitButton to use the recall feature Recording a telephone conversation using the handsetTo adjust the speaker volume To redial the last number dialledAnswering calls using the handset Answering calls using the base unitCategories Handset phonebookAdding entries to the handset phonebook Finding and calling a handset phonebook entryOne touch dial Erasing entries from the handsetPhonebook Editing entries in the handset PhonebookMaking a call using a one touch dial key Chain dialErasing a one touch dial assignment Shared phonebook Adding entries to the shared phonebookFinding and calling a shared phonebook entry Changing a name, phone number, audible call Editing entries in the shared phonebookErasing entries from the shared phonebook Playing back an audible call announcementCopying handset phonebook entries to the shared phonebook Copying phonebook entriesCopying handset phonebook entries to other handset Copying one entryGuide to handset settings Handset settings Sub-menu Default setting MenuAlarm Time settingsRinger setup Ringer volumeTurning night mode on/off Night modeSetting the start and end time for night mode Setting the ring delay for night modeSelecting categories to bypass night mode Display setupSelecting the standby mode display Changing the display languageCall options Other optionsResetting the handset to its default settings Guide to base unit settings Base unit Sub-menu Default setting Settings menuNight mode Storing/changing emergency numbers Setting pause lengthChanging the recall time Selecting area codes to be deleted automaticallySetting call restriction Resetting the base unit to its default settings Changing the base unit PIN Personal Identification NumberUsing Caller ID service Category features for handset phonebookViewing the caller list and calling back Caller listAudible call for shared phonebook Editing a caller’s phone number before calling backCall minder Storing caller information into the handset phonebookAnswering system Greeting messageListening to messages Using a prerecorded greeting messageUsing the handset Playing back the greeting messageListening to new/all messages Erasing all messagesDirect command operation using the handset Calling back using the handset Caller ID subscribers onlyKey Direct commands Turning remote operation on/off Using the answering system remotelyRemote operation Voice guidanceAnswering Default System setting Setting Remote commandsKey Remote command Turning on the answering system remotelySelecting the caller’s recording time Turning call screening on/offTurning message alert on/off Answering System Features Additional handsets Operating additional unitsRegistering a handset to a base unit Additional base unitsCancelling a handset Selecting a base unitIncreasing the range of the base unit Cancelling a base unitIntercom Between a handset and the base unitBetween handsets From a handset to the base unitFrom the base unit to a handset Transferring a call without speaking to the handset user Wall mounting Screws Hook 108 mmAvailable character entries Character entry modesExtended 1 character table N Extended 2 character table OCyrillic character table P Troubleshooting Initial settingsProblem Cause & solution Telephone Redial the number manually Answering system Specifications Index PINIndex Customer Support Centre Tel. No 272 Sales Department Copyright