Lincoln Electric IM915 manual Shielding GAS Connection, Cylinder may explode if damaged

Page 21

A-13

INSTALLATION

A-13

 

 

 

SHIELDING GAS CONNECTION

WARNING

CYLINDER may explode if damaged.

• Keep cylinder upright and chained to a

support.

• Keep the cylinder away from all areas where it may be damaged.

•Never lift the welder with cylinder attached.

•Never allow the welding electrode to touch cylinder.

•Keep the cylinder away from welding or other live electrical circuits.

bUILDUP OF SHIELDING GAS may harm health or kill.

• Shut off the shielding gas supply when it is not in use.

SEE AMERICAN NATIONAL STANDARD Z-49.1, “SAFETY IN WELDING AND CUTTING” PUBLISHED BY THE AMERICAN WELDING SOCIETY.

------------------------------------------------------------------------

Maximum inlet pressure is 100 psi. (6.9 bar.)

Install the shielding gas supply as follows:

1.Secure the cylinder to prevent it from falling.

2.Remove the cylinder cap. Inspect the cylinder valves and regulator for damaged threads, dirt, dust, oil or grease. Remove dust and dirt with a clean cloth. DO NOT ATTACH THE REGULATOR

IF OIL, GREASE OR DAMAGE IS PRESENT! Inform your gas supplier of this condition. Oil or grease in the presence of high pressure oxygen is explosive.

3.Stand to one side away from the outlet and open the cylinder valve for an instant. This blows away any dust or dirt which may have accumulated in the valve outlet.

4.Attach the flow regulator to the cylinder valve and tighten the union nut(s) securely with a wrench. Note: if connecting to 100% CO2 cylinder, insert regulator adapter between regulator and cylinder valve. If adapter is equipped with a plastic washer, be sure it is seated for connection to the CO2 cylin- der.

5.Attach one end of the inlet hose to the outlet fitting of the flow regulator. Attach the other end to the welding system shielding gas inlet. Tighten the union nuts with a wrench.

6.Before opening the cylinder valve, turn the regulator adjusting knob counterclockwise until the adjusting spring pressure is released.

7.Standing to one side, open the cylinder valve slowly a fraction of a turn. When the cylinder pressure gage stops moving, open the valve fully.

8.The flow regulator is adjustable. Adjust it to the flow rate recommended for the procedure and process being used before making a weld.

POWER FEED™ 10M SINGLE WIRE FEEDER

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Safety Depends on You Power Feed 10M Single Wire Feeder JulySafety Electric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionPrécautions DE Sûreté Thank You TAbLE of Contents Vii Temperature Rating SPEC.# Type Input PowerPower Feed 10M Single Wire Feeder Welding Capacity RatingLocation Electric Shock can killMounting Weld CAbLE SIzINGPower Source COAxIAL Weld CAbLESElectrode Work Negative Electrode Polarity DIP Switch #7 Position PolarityWire Feeder Welding Gun/Wire Feeder Trigger ConnectorPower Source Pin Function Wire Feeder Pin FunctionDescription Changing Drive Rolls and Wire GuidesChanging the GUN Receiver bUSHING Drive Roll Pressure SettingWelding GUNS, Torches and ACCES- Sories GUN Receiver bUSHINGMagnum GUN and CAbLE ASSEMbLIES Wire Feed Shut Down Circuit Changing the Gear RatioTo change the gear ratio DIP Switch #8 Position Gear Ratio Wire Reel LoadingSpindle Placement Loading 16 to 44 lb .3 20kg SpoolsFigure A.10 Using K1504-1 Coil ReelWeld Wire Routing Loading 30 lb .6 kg Readi-Reels See Figure A.11Removing a Readi-Reel Shielding GAS Connection Cylinder may explode if damagedBUILDUP OF SHIELDING GAS may harm health or kill ExAMPLES of Connecting AN Arclink Power Wave System Welding Sparks can cause fire or explosion Fumes and Gases can be dangerousARC Rays can burn Common Welding AbbREVIATIONSRecommended Processes Product DescriptionRequired Equipment Additional Required EquipmentCV Welding Pulse Welding or STT Welding Front Panel Controls and Connections Status LED Volts / Trim Display Prior to WeldingSynergic CV Voltage Display Overview Mode Select Panel 4 MSP4LAYOUT-CONTROLS see Figure b.3 LAYOUT-DIGITAL DisplayChanging Weld Modes POWER-UP SequenceChanging ARC Wave Control Infrared IR ControlLimit Setting Machine SETUP/USER PreferencesAccessing the Machine Setup Menu Figure b.3a Setup Menu SET-UP Features MenuUser Defined Parameters Stall Factor Adjustment Parameter Definition Procedure Change MethodCrater Delay Parameter Definition Gun Offset AdjustmentReset Consumable Weight TIG Gas ControlParameter Definition Push-Pull Gun Knob behavior Arc Start/Loss Error TimeDisplay Trim as Volts Option Sense From Studs107 View Power Source Protocol 100 View DiagnosticsParameter Definition Show Test Modes 102 View Fatal Logs504 Mode Select Panel Lock 503 Memory button Disable505 Setup Menu Lock Parameter Definition 501 Encoder LockoutOnly be accessed using Power Wave Manager software Parameter Definition 506 Set User Interface Passcode509 UI Master Lockout Cold Feed / GAS Purge Switch Step / 4-STEP Trigger SwitchStep Trigger Operation Sequence of Operation Step Trigger OperationFigure b.5 Process Setup and Operation Non- SynergicModes ARC Control Steel and Stainless Synergic GMAW-P Pulsed MIG WeldingPulse-on-Pulse Welding CC Stick Modes Machine Functionality bY Weld ProcessProcess Weld Mode Output Control KNObS, Weld Mode 5CV GMAW/FCAW NON-SYNERGIC CV NON-SYNERGIC ModesGmaw Synergic Wire SIzE 030 035 045 052Synergic CV Modes Material Process GASWire SIzE Pulse and PULSE-ON-PULSE SynergicPulse and PULSE-0N-PULSE Modes STT and STT II NONN-SYNERGIC MAW-S TT WE L D ModeWIR E S IZE 035 045 052Gtaw Touch Start TIG Welding Gtaw TIG WeldingTouch Start TIG All Metals Touch Start TIGWeld Mode Searching Searching for a Weld ModeUser Memories Limit Setting Enable Optional AccessoriesAccessories Lb. coils to 2 spindles Routine Maintenance Safety PrecautionsPeriodic Maintenance CALIbRATION SpecificationTROUbLESHOOTING Symptoms PRObLEMSPOSSIbLE Cause Recommended Course of ActionArclink System Error Codes Your local Lincoln Authorized Output PRObLEMS TROUbLESHOOTING PRObLEMS POSSIbLE Feeder Power Feed 10M Single Wire30.46 14.56 18.48 15.80Power Feed 10M Single Wire Feeder Power Feed 10M Single Wire Feeder Precaucion Warnung
Top Page Image Contents