Lincoln Electric IM915 manual User Defined Parameters

Page 33

b-11				OPERATION	b-11

				USER DEFINED PARAMETERS

	Parameter			Definition
				Exit Setup Menu
		P.0		This setup menu parameter can be used to exit the setup menu. When P.0 is displayed, press
				the left Mode Select button to exit the setup menu.

		P.1		Wire Feed Speed Units
				This option selects which units to use for displaying wire feed speed.
				English = inches/minute wire feed speed units (default).
				Metric = meters/minute wire feed speed units.

		P.2		Arc Display Mode
				This option selects what value will be shown on the upper left display while welding.
				Amps = The left display shows Amperage while welding (default).
				WFS = The left display shows Wire Feed Speed while welding.

		P.3		Display Options
				This setup parameter was previously named "Display Energy"
				If the previous software revision had this parameter set to display energy, that selection will
				remain.
				This option selects the information displayed on the alphanumeric displayes while welding. Not
				all P.3 selections will be available on all machines. In order for each selection to be included in
				the list, the power source must support that feature. A software update of the power source may
				be needed to include the features.
				Standard Display = The lower displays will continue to show preset information during and after
				a weld (default).
				Show Energy = Energy is displayed, along with time in HH:MM:SS format.
				Show Weld Score = The accumulative weld score result is shown.

		P.4		Recall Memory with Trigger
				This option allows a memory to be recalled by quickly pulling and releasing the gun trigger. To
				recall a memory, quickly pull and release the trigger the number of times that correspond to the
				memory number. For example, to recall memory 3, quickly pull and release the trigger 3 times.
				To recall memory 1, quickly pull and release the trigger the number of user memories plus 1.
				Memories cannot be recalled while the system is welding.
				Disabled = The gun trigger cannot be used to recall user memories (default).
				Enabled = The gun trigger can be used to recall user memories.

POWER FEED™ 10M SINGLE WIRE FEEDER

Image 33

Contents Safety Depends on You Power Feed 10M Single Wire Feeder JulySafety Electric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionPrécautions DE Sûreté Thank You TAbLE of Contents Vii Temperature Rating SPEC.# Type Input PowerPower Feed 10M Single Wire Feeder Welding Capacity RatingLocation Electric Shock can killMounting Weld CAbLE SIzINGPower Source COAxIAL Weld CAbLESElectrode Work Negative Electrode Polarity DIP Switch #7 Position PolarityWire Feeder Welding Gun/Wire Feeder Trigger ConnectorPower Source Pin Function Wire Feeder Pin FunctionDescription Changing Drive Rolls and Wire GuidesChanging the GUN Receiver bUSHING Drive Roll Pressure SettingWelding GUNS, Torches and ACCES- Sories GUN Receiver bUSHINGMagnum GUN and CAbLE ASSEMbLIES Wire Feed Shut Down Circuit Changing the Gear RatioTo change the gear ratio DIP Switch #8 Position Gear Ratio Wire Reel LoadingSpindle Placement Loading 16 to 44 lb .3 20kg SpoolsFigure A.10 Using K1504-1 Coil ReelWeld Wire Routing Loading 30 lb .6 kg Readi-Reels See Figure A.11Removing a Readi-Reel Shielding GAS Connection Cylinder may explode if damagedBUILDUP OF SHIELDING GAS may harm health or kill ExAMPLES of Connecting AN Arclink Power Wave System Welding Sparks can cause fire or explosion Fumes and Gases can be dangerousARC Rays can burn Common Welding AbbREVIATIONSRecommended Processes Product DescriptionRequired Equipment Additional Required EquipmentCV Welding Pulse Welding or STT Welding Front Panel Controls and Connections Status LED Volts / Trim Display Prior to WeldingSynergic CV Voltage Display Overview Mode Select Panel 4 MSP4LAYOUT-CONTROLS see Figure b.3 LAYOUT-DIGITAL DisplayChanging Weld Modes POWER-UP SequenceChanging ARC Wave Control Infrared IR ControlLimit Setting Machine SETUP/USER PreferencesAccessing the Machine Setup Menu Figure b.3a Setup Menu SET-UP Features MenuUser Defined Parameters Stall Factor Adjustment Parameter Definition Procedure Change MethodCrater Delay Parameter Definition Gun Offset AdjustmentReset Consumable Weight TIG Gas ControlParameter Definition Push-Pull Gun Knob behavior Arc Start/Loss Error TimeDisplay Trim as Volts Option Sense From Studs107 View Power Source Protocol 100 View DiagnosticsParameter Definition Show Test Modes 102 View Fatal Logs504 Mode Select Panel Lock 503 Memory button Disable505 Setup Menu Lock Parameter Definition 501 Encoder LockoutOnly be accessed using Power Wave Manager software Parameter Definition 506 Set User Interface Passcode509 UI Master Lockout Cold Feed / GAS Purge Switch Step / 4-STEP Trigger SwitchStep Trigger Operation Sequence of Operation Step Trigger OperationFigure b.5 Process Setup and Operation Non- SynergicModes ARC Control Steel and Stainless Synergic GMAW-P Pulsed MIG WeldingPulse-on-Pulse Welding CC Stick Modes Machine Functionality bY Weld ProcessProcess Weld Mode Output Control KNObS, Weld Mode 5CV GMAW/FCAW NON-SYNERGIC CV NON-SYNERGIC ModesGmaw Synergic Wire SIzE 030 035 045 052Synergic CV Modes Material Process GASWire SIzE Pulse and PULSE-ON-PULSE SynergicPulse and PULSE-0N-PULSE Modes STT and STT II NONN-SYNERGIC MAW-S TT WE L D ModeWIR E S IZE 035 045 052Gtaw Touch Start TIG Welding Gtaw TIG WeldingTouch Start TIG All Metals Touch Start TIGWeld Mode Searching Searching for a Weld ModeUser Memories Limit Setting Enable Optional AccessoriesAccessories Lb. coils to 2 spindles Routine Maintenance Safety PrecautionsPeriodic Maintenance CALIbRATION SpecificationTROUbLESHOOTING Symptoms PRObLEMSPOSSIbLE Cause Recommended Course of ActionArclink System Error Codes Your local Lincoln Authorized Output PRObLEMS TROUbLESHOOTING PRObLEMS POSSIbLE Feeder Power Feed 10M Single Wire30.46 14.56 18.48 15.80Power Feed 10M Single Wire Feeder Power Feed 10M Single Wire Feeder Precaucion Warnung