Wagner SprayTech HIGH PERFORMANCE AIRLESS SPRAYER owner manual Cleanup INLET/OUTLET Valves

Page 10

CLEANUP (CONTINUED)

INLET/OUTLET VALVES

CLEANING THE SPRAY GUN COMPONENTS

1.Perform Pressure Relief Procedure, page 5.

2. Remove spray gun from the paint hose using adjustable wrenches.

3. Remove filter from spray gun (refer to Unclogging the Spray Gun Filter, page 8).

4. Remove spray tip from spray guard assembly.

CLEANING THE INLET VALVE

Cleaning or servicing the inlet valve may be required if the unit has priming problems. This may be caused by improper cleaning and/or storage. Replacement kits may be ordered by calling customer service.

1. Remove the inlet filter from the bottom of the hopper. You may need to use a screwdriver to pry the filter loose.

2. Insert the inlet valve tool into the inlet fitting. Twist counter-clockwise and remove from its housing.

You willl need to attach the inlet valve tool to a ratchet wrench extension in order to remove it.

Filter

Housing

5.Clean spray tip and filter with a soft-bristled brush and the appropriate cleaning solution. Be sure to remove and clean the washer and saddle seat located in the rear of the spray tip assembly.

Saddle Washer seat

6.Pour a few drops of household oil inside the gun housing (see area indicated below by arrow).

7.Reassemble spray gun:

3.Inspect the three inlet fitting O-rings on the inlet fitting. Clean or replace, and lubricate with household oil.

DO NOT remove the O-rings on the inlet fitting to clean them. Remove ONLY if you plan to replace them.

4.Retrieve the inlet valve and the inlet valve O-ring from the inlet fitting housing. Clean or replace and lubricate the O-ring with a light household oil.

5.Set the inlet valve O-ring back into the housing, and set the inlet valve on top of it.

6.Replace inlet fitting into the housing. Tighten with the inlet valve tool and ratchet.

Inlet fitting O-ring

Inlet fitting O-ring

Inlet fitting

Inlet fitting O-ring

Inlet valve

Inlet valve O-ring

• install gun filter tapered-end first, and,

• install spray tip, saddle seat and washer, and replace spray guard assembly.

Filter

Housing

8.Thread the paint hose back onto the spray gun. Tighten with a wrench.

IMPORTANT!

If you cleaned your pump using mineral spirits, it is recommended that you flush the pump again using warm, soapy water to prepare it for storage. Repeat Flushing the Pump instructions.

REPLACING THE OUTLET VALVE

Replacement of the outlet valve may be necessary if your spray performance remains poor after having performed all the steps contained in the Spraying Troubleshooting section of this manual. Replacement valves are available by calling customer service.

1.Unscrew the outlet valve from the outlet valve housing using an adjustable wrench.

2. Inspect the inside of the outlet valve housing. Remove any accumulated paint.

3. Replace with a new outlet valve. Tighten into outlet valve housing with an adjustable wrench.

English

Customer Service: 800-328-8251 10

© 2003 Wagner Spray Tech - All rights reserved.

 

 

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Specifications Table of ContentsPaint Crew High Performance Airless Sprayer Safety Information Read ALL Safety Grounding Instructions Important Electrical InformationProduct Registration Card Assembly Components and AssemblyTools Needed for Assembly Components Controls and FunctionsBefore YOU Begin Purging and Priming the Pump Purging and PrimingPurging and Priming the Spray Hose Practice SprayingSpraying Technique Unclogging the Spray TIP Spraying TroubleshootingUnclogging the Spray GUN Filter Unclogging the Inlet FilterRinsing the Hopper CleanupPurging the Paint Hose Flushing the SprayerCleaning the Inlet Valve Cleanup INLET/OUTLET ValvesCleaning the Spray GUN Components Replacing the Outlet ValvePreparing the Sprayer for LONG- Term Storage StorageSHORT-TERM Storage UP to 16 Hours ShutdownExtended Maintenance MaintenanceDaily Maintenance 0515221 Inlet valve seal kit 0515205 Outlet valve kitPoids 11,3 Kg Capacité Paint Crew Pulvérisateur Sans AIR PerformantTable DES Matières Moteur universel de 3/8 chConsignes DE SÉ Curite Lire Toutes CES Directives DE Mise À LA Terre Renseignements Importants SUR L’É LectricitéCarte Denregistrement DU Produit Composants Commandes ET FonctionsComposants ET Assemblage Outils RequisVidange DU Distributeur Verrouillage ET DÉ Verrouillage DU PistoletBranchement DU Pulvé Risateur DÉ CompressionPurge ET Amorç AGE DE LA Pompe Purging ET Amorç AGEPurge ET Amorç AGE DU Flexible Essais Pulvé RisationTechniques DE Pulvé Risation Nettoyage DE L’EMBOUT DE Pulvé Risation Problè MES PotentielsNettoyage DU Filtre DE Pistolet Nettoyage DU Filtre D’ENTRÉ ERinç AGE DU Distributeur NettoyagePurge DU Flexible Purge DE Pulvé RisateurNettoyage DE LA Soupape D’ENTRÉ E Remplacement DE Soupape DE SortieNettoyage Suite Soupapes D’ENTRÉ E/SORTIE Nettoyage DES Composants DU PulvérisateurPRÉ Paration Pour LE Rangement RangementRangement À Court Terme JUSQU’À 16 Heures PRÉ Paration EN VUE DE LA RÉ -UTILISATIONEntretien Quotidien MAINTENANCE/DÉ PannageMaintenance À Long Terme De piè ce DescriptionContenido Paint Crew Rociador SIN Aire DE Alto RendimientoEspecificaciones Informació N DE Seguridad LEA Toda LA Instrucciones Para LA Conexió N a Tierra Informació N ELÉ Ctrica ImportanteTarjeta DE Registro DEL Producto Herramientas Necesarias Para LA Preparació N Componentes Y AssemblajeComponentes Controles Y FuncionesAntes DE Comenzar Purga Y Cebado DE LA Manguera Purga Y CebadoPurga Y Cebado DE LA Bomba Nivel de materialPRÁ Ctica RociadoTÉ Cnica DE Aplicació N Desbloqueo DE LA Filtro DE Entrada Solució N DE Problemas DE Aplicació NDesbloqueo DE LA Boquilla Rociadora ¡NUNCA Perfore EL Filtro CON UN Instrumento AfiladoLimpieza DEL Recipiente LimpiezaPurga DE LA Manguera Limpieza DEL RociadorCÓ MO Reemplazar LA VÁ Lvula DE Salida Limpieza Continuació NLimpieza DE LA VÁ Lvula DE Entrada Limpieza DE LOS Componentes DE LA PistolaParo AlmacenamientoAlmacenamiento DE Corto Plazo Hasta 16 Horas ArranqueMantenimiento Diario MANTENIMIENTO/SOLUCIÓ N DE ProblemasSolució N DE Problemas Advertencia Mantenimiento a Largo PlazoSpray GUN Pistolet Pistola Parts List Liste DE PIÈ CES Lista DE PiezasSpray Hose Flexible DE Pulvé Risation Manguera DEL Rociador Trousse de boulon, rondelle, et Replacement parts available by calling customer serviceSprayer Pulvé Risateur Rociador Juego de perno, rondana, yService Centers Centres DE Service Centros DE Servicio Georgia DelawareFlorida HawaiiMaine MassMaryland MichiganOklahoma DakotaOhio OregonWyoming Vermont WashingtonWisconsin CanadaMinneapolis, Minnesota Wagner Spray Tech CorporationFernbrook Lane Telephone
Related manuals
Manual 20 pages 25.24 Kb
Top Page Image Contents