Wagner SprayTech HIGH PERFORMANCE AIRLESS SPRAYER SHORT-TERM Storage UP to 16 Hours, Shutdown

Page 11

STORAGE

SHORT-TERM STORAGE (UP TO 16 HOURS)

Follow these steps when using LATEX PAINTS ONLY. If using materials that are oil-based, follow the long-term storage steps.

SHUTDOWN

1.Perform all the steps of the PRESSURE RELIEF PROCEDURE (page 5).

PRIME

SPRAY

O

 

 

2.Pour 1/2 cup water slowly on top of the paint to prevent it from drying. Replace the hopper lid.

3.Wrap the spray gun assembly in a damp cloth and place it in a plastic bag. Seal the bag shut.

4.Unplug the sprayer.

5.Place the sprayer in a safe place out of the sun for short- term storage.

STARTUP

1.Remove the gun from the plastic bag and stir the water into the paint.

PREPARING THE SPRAYER FOR LONG- TERM STORAGE

1.Make sure you have already completed the Cleanup steps on pages 9-10.

2.Remove the inlet filter. You may need to use a screwdriver to pry it loose.

Inlet filter

3.Pour approximately two ounces of light household oil into the inlet valve.

Inlet valve

4.Remove hose from outlet valve, place a rag over the outlet valve, and turn the switch ON. Let the unit run for five seconds.

5.Switch the pump OFF.

O

2.Check to be sure the PRIME/SPRAY knob is set to PRIME.

3.Plug sprayer in and turn the switch to ON.

4.Turn the PRIME/SPRAY knob to SPRAY.

5.Test the sprayer on a practice piece and begin spraying.

PRIME

SPRAY

SPRAY

PRIME

6.Replace the inlet filter and push the tab on the filter.

Tab

7.Wipe the entire unit, hose and gun with a damp cloth to remove accumulated paint.

8.Replace the high pressure hose to the outlet valve and replace the hopper lid.

© 2003 Wagner Spray Tech - All rights reserved.

11 Customer Service: 800-328-8251

English

 

 

 

Image 11
Contents Paint Crew High Performance Airless Sprayer Table of ContentsSpecifications Safety Information Read ALL Safety Product Registration Card Important Electrical InformationGrounding Instructions Components Controls and Functions Components and AssemblyTools Needed for Assembly AssemblyBefore YOU Begin Purging and Priming the Spray Hose Purging and PrimingPurging and Priming the Pump Spraying Technique SprayingPractice Unclogging the Inlet Filter Spraying TroubleshootingUnclogging the Spray GUN Filter Unclogging the Spray TIPFlushing the Sprayer CleanupPurging the Paint Hose Rinsing the HopperReplacing the Outlet Valve Cleanup INLET/OUTLET ValvesCleaning the Spray GUN Components Cleaning the Inlet ValveShutdown StorageSHORT-TERM Storage UP to 16 Hours Preparing the Sprayer for LONG- Term Storage0515221 Inlet valve seal kit 0515205 Outlet valve kit MaintenanceDaily Maintenance Extended MaintenanceMoteur universel de 3/8 ch Paint Crew Pulvérisateur Sans AIR PerformantTable DES Matières Poids 11,3 Kg CapacitéConsignes DE SÉ Curite Lire Toutes CES Carte Denregistrement DU Produit Renseignements Importants SUR L’É LectricitéDirectives DE Mise À LA Terre Outils Requis Commandes ET FonctionsComposants ET Assemblage ComposantsDÉ Compression Verrouillage ET DÉ Verrouillage DU PistoletBranchement DU Pulvé Risateur Vidange DU DistributeurPurge ET Amorç AGE DU Flexible Purging ET Amorç AGEPurge ET Amorç AGE DE LA Pompe Techniques DE Pulvé Risation Pulvé RisationEssais Nettoyage DU Filtre D’ENTRÉ E Problè MES PotentielsNettoyage DU Filtre DE Pistolet Nettoyage DE L’EMBOUT DE Pulvé RisationPurge DE Pulvé Risateur NettoyagePurge DU Flexible Rinç AGE DU DistributeurNettoyage DES Composants DU Pulvérisateur Remplacement DE Soupape DE SortieNettoyage Suite Soupapes D’ENTRÉ E/SORTIE Nettoyage DE LA Soupape D’ENTRÉ EPRÉ Paration EN VUE DE LA RÉ -UTILISATION RangementRangement À Court Terme JUSQU’À 16 Heures PRÉ Paration Pour LE RangementDe piè ce Description MAINTENANCE/DÉ PannageMaintenance À Long Terme Entretien QuotidienEspecificaciones Paint Crew Rociador SIN Aire DE Alto RendimientoContenido Informació N DE Seguridad LEA Toda LA Tarjeta DE Registro DEL Producto Informació N ELÉ Ctrica ImportanteInstrucciones Para LA Conexió N a Tierra Controles Y Funciones Componentes Y AssemblajeComponentes Herramientas Necesarias Para LA Preparació NAntes DE Comenzar Nivel de material Purga Y CebadoPurga Y Cebado DE LA Bomba Purga Y Cebado DE LA MangueraTÉ Cnica DE Aplicació N RociadoPRÁ Ctica ¡NUNCA Perfore EL Filtro CON UN Instrumento Afilado Solució N DE Problemas DE Aplicació NDesbloqueo DE LA Boquilla Rociadora Desbloqueo DE LA Filtro DE EntradaLimpieza DEL Rociador LimpiezaPurga DE LA Manguera Limpieza DEL RecipienteLimpieza DE LOS Componentes DE LA Pistola Limpieza Continuació NLimpieza DE LA VÁ Lvula DE Entrada CÓ MO Reemplazar LA VÁ Lvula DE SalidaArranque AlmacenamientoAlmacenamiento DE Corto Plazo Hasta 16 Horas ParoMantenimiento a Largo Plazo MANTENIMIENTO/SOLUCIÓ N DE ProblemasSolució N DE Problemas Advertencia Mantenimiento DiarioSpray Hose Flexible DE Pulvé Risation Manguera DEL Rociador Parts List Liste DE PIÈ CES Lista DE PiezasSpray GUN Pistolet Pistola Juego de perno, rondana, y Replacement parts available by calling customer serviceSprayer Pulvé Risateur Rociador Trousse de boulon, rondelle, etService Centers Centres DE Service Centros DE Servicio Hawaii DelawareFlorida GeorgiaMichigan MassMaryland MaineOregon DakotaOhio OklahomaCanada Vermont WashingtonWisconsin WyomingTelephone Wagner Spray Tech CorporationFernbrook Lane Minneapolis, Minnesota
Related manuals
Manual 20 pages 25.24 Kb