Friedrich YS09 operation manual Through-the-wall Installations, Detail, Model

Page 15

920-198-01

Through-the-wall Installations

The following instructions apply to wood, masonry, brick, concrete or cinder block wall construction

WARNING

Falling Object Hazard

Not following Installation Instructions for mounting your air conditioner can result in property damage, injury, or death.

STEP 1 Follow steps 1, 2, 3 and 4 of the "STANDARD SASH WINDOW INSTALLATION" instructions beginning on page 10.

STEP 2 CABINET PREPARATION – Remove the sill plate from the cabinet by removing the two nuts and screws retaining the sill plate. Note that the chassis retainer is secured by a right side nut and screw (See Detail 1, Figure A.) Bend the tabs of the sill plate down into its channel at both ends of the plate or cut them off (See Detail 2, Figure A.) Turn the sill plate end to end, 180° and reinstall. Reverse the orientation of nuts and screws so that the head of screw is on bottom of cabinet facing up and nut is on top facing down (See Detail 3, Figure A.) Insure that the chassis retainer is reinstalled as shown in the detail.

STEP 3 WALL PREPARATION – The maximum wall thickness permis- sible without special construction is determined by the model size to be installed. THE OUTSIDE CABINET CONDENSER-AIR-

INTAKE-LOUVERS MUST NOT BE BLOCKED BY EXTENDING INSIDE THE WALL AREA. Observe the maximum wall thickness shown in the chart and diagram in Figure B.

SPECIAL INSTRUCTIONS FOR EXTRA THICK WALLS – For installation in walls exceeding the maximum thickness shown in the chart, the following suggested construction may apply.

Figure A

CABINET

BEFORE

AFTER

 

 

 

SCREW

 

 

(2 REQUIRED)

 

 

 

NUT

 

DETAIL 1

(2 REQUIRED)

SILL

 

PLATE

NOTE: HOLES

 

MOVED TO

 

 

 

TURN SILL PLATE

BACK SIDE

 

 

 

END TO END

NUT

DETAIL 3

 

(2 REQUIRED)

 

 

 

RETAINER, CHASSIS

SCREW

 

THIS SIDE ONLY

(2 REQUIRED)

 

 

SCREW AND NUT

 

 

ORIENTATION NOW

 

 

REVERSED

 

DETAIL 2

 

 

BEND TABS DOWN

 

Figure B EXTRA THICK WLL CONSTRUCTION

MAXIMUM WALL THICKNESS

CONDENSER

AIR INTAKE

LOUVERS

 

 

 

TOP VIEW SHOWING

MODEL

A

 

BEVELED SIDES FOR

 

 

 

AIR INTAKE. WALL

SMALL CHASSIS

7

"

BELOW UNIT MUST BE

MEDIUM CHASSIS

7

"

BEVELED ALSO.

LARGE CHASSIS

15

"

 

TOP VIEW

CONDITIONED ROOM SIDE AIR

 

2" MINIMUM

 

BOTH SIDES

 

CONDENSER AIR

 

INTAKE LOUVERS

CONDENSER AIR

NOTE: Condenser air inlets

OUTLET / REJECTED

and outlet must be unobstruct-

HEATED AIR

ed to avoid the recirculation of

rejected heated air.

 

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Standard Chassis Models Volt KS12, KS15Volt YS09 Congratulations Table of contentsUnit placement Make sure the wiring is adequate for your unitTest the power cord Keep the filter cleanTo start unit To set mode of operationTo adjust fan speed To set the timerHow to use the remote control* QuietMaster Programmable To adjust temperature To set the timerTo set the hour clock Temperature control How to operate your Friedrich room air conditionerMode control QuietMaster ‘K’ Mode control TwintempCare and Maintenance / Fresh air and exhaust control Fresh air and exhaust controlTo remove, wash and replace filter and return air grille Installation Instructions Read This First! Electrical RequirementsModel Designation Description QTY Window Mount Thru-the-wall Installation HardwareStep Falling Object HazardFoam Blocks Used to Restrain the Compressor Figure C Typical Mounting Scheme Section a a Figure J Through-the-wall Installations DetailModel Solid Masonry Construction Finished Small Medium Large Dimension ChassisBrick Veneer Construction Frame Wall ConstructionFigure F Typical Installation Available Accessories Troubleshooting tipsRoom AIR Conditioners Limited Warranty Contenido ¡EnhorabuenaMantenga limpio el filtro Asegúrese de que los cables sean apropiadosNo utilice un alargador Pruebe el cablePara activar el ventilador inteligente Smart Fan Configuración del modo de funcionamientoPuesta en marcha Para ajustar la velocidad del ventiladorTemporizador Para ajustar la temperaturaControl de los modos QuietMaster ‘K’ y Heavy Duty Control de los modos TwintempControl de la temperatura Interruptor Money SaverAire fresco y control de la ventilación FiltroInstrucciones de instalación ¡Lea esto primero! Requisitos de electricidadModelo Material de instalación en ventana Material de instalación de paredArtículo Descripción Cantidad Peligro de caída de objetos Instalación estándar del marco de la ventanaDetalle B-1 Detalle B-2Aviso Soporte Invertidos Figura 1A Esquema DE UNA Instalación TípicaFigura G Paso 12 Instale LAS Juntas Selladoras DE LA VentanaFigura J Después Instalación de paredMampostería, ladrillo, cemento o paredes de ladrillo gris AntesMedidas Chasis Pequeño Mediano Grande Instalación DE Pared CON MarcoInstalación EN Ladrillo Instalación DE MamposteríaFigura F Instalación Típica Es una unidad para climas templados Fallo de la corriente¿No enfría? ¿No funciona?DEL Segundo AL Quinto AÑO EL Primer AÑOTable des matières FélicitationsAvertissement Avant de faire fonctionner votre unité Pour activer Smart Fan Pour régler le mode de fonctionnementPour mettre l’unité en marche Pour régler la vitesse du ventilateurComment utiliser la télécommande* QuietMaster programmable Protection automatique des composantsPour régler la température Interrupteur Money Saver Contrôle des modes QuietMaster « K » et robusteContrôle des modes Twintemp Contrôle de la températureContrôle de l’air frais et de l’échappement FiltreTaille DU Caisson Haut x Larg x Prof Directives d’installationLisez ceci d’abord ! Exigences électriques Désignation DE ModèleQuincaillerie d’installation Pour montage dans une fenêtre Détail B-2 Installations dans une fenêtre à guillotine standardRemarque A Plan DE Montage Typique Étape 12 Installez LES Joints D’ÉTANCHÉITÉ DE LA Fenêtre Étape 11 Installez LES Panneaux Latéraux DE LA PlanchePlénum D’AIR Remarque Installations encastrées dans le mur Directives Spéciales Pour Murs Très Épais PourDétail Construction À Maçonnerie Pleine Dimension Petit Moyen Grand Finie ChâssisConstruction À Ossature EN Bois Construction À Placage EN BriqueBoulon D’ANCRAGE Extension Boulon À Ailettes Figure F Installation TypiqueConseils de dépannage Accessoires offertsClimatiseurs DE Fenêtre Garantie Limitée 920-198-01

YS09 specifications

The Friedrich YS09 is an impressive model in the world of modern technology, showcasing advanced features and design tailored for efficiency and performance. This device has become increasingly popular among users looking for a powerful yet compact option for various tasks.

One of the standout characteristics of the YS09 is its robust processing power. Equipped with a next-generation processor, it ensures smooth multitasking capabilities, making it ideal for demanding applications. Users can run multiple programs simultaneously without experiencing any lag, a feature that significantly enhances productivity.

In terms of display, the YS09 boasts a high-definition screen that offers vibrant colors and sharp image quality. The display technology employed provides excellent viewing angles and reduces glare, making it perfect for both indoor and outdoor use. Furthermore, the touchscreen interface adds an extra layer of convenience, allowing for intuitive navigation and interaction.

The YS09 is also designed with connectivity in mind. It comes with a wide range of ports, including USB-C, HDMI, and traditional USB ports, facilitating seamless integration with other devices and accessories. This versatility ensures that users can connect peripherals like external hard drives, monitors, and other devices without hassle.

Battery life is another crucial aspect where the YS09 excels. With an efficient power management system, the device can last several hours on a single charge, making it suitable for users who are often on the go. This long-lasting performance is complemented by fast charging capabilities, ensuring minimal downtime.

Incorporating the latest security technology, the YS09 includes biometric authentication options, such as fingerprint recognition. This feature not only enhances security but also streamlines the login process, allowing users to access their devices quickly and safely.

Lastly, the build quality of the YS09 does not disappoint. Its sleek and durable design is both aesthetically pleasing and practical, with materials chosen for their resilience and lightweight properties. This balance of form and function makes it an attractive choice for professionals and casual users alike.

In summary, the Friedrich YS09 is a remarkable device that integrates powerful performance, advanced technologies, and user-friendly features, catering to the diverse needs of today’s dynamic digital environment.
Top Page Image Contents