DeWalt D55146R instruction manual Preparation for USE, Pre-Start Checklist Fig, Initial Set-up Fig

Page 12

B

English

A

B

A

 

B

 

 

2. Pull handle (A) until fully extended (lock position).

WARNING: Risk of unsafe operation. Ensure proper footing and use caution when rolling compressor so that unit does not tip or cause loss of balance.

3.To move, roll compressor on tires using handle (A) as shown above.

Store compressor in a vertical or horzitional position.

PREPARATION FOR USE

Pre-Start Checklist (Fig. 1)

1.Ensure the On/Off switch (L) is in the OFF position.

2.Plug the power cord into the correct branch circuit receptacle. See Voltage and Circuit Protection under Installation.

3.Ensure air tank is drained, see Draining Air Tank under Maintenance.

4.Ensure the drain valve is closed.

5.Ensure safety valve (G) is functioning properly, see Checking Safety Valve under Maintenance.

6.Turn regulator knob (F) counterclockwise until fully closed. Ensure regulated pressure gauge reads 0 PSI (0 kPa).

7.Attach hose and accessories. NOTE: Always use a minimum 3/8" or greater air hose rated at 300 PSI.

WARNING: Risk of unsafe operation. Firmly grasp hose in hand when installing or disconnecting to prevent hose whip.

8.Ensure all covers and labels are in place, legible (for labels) and securely mounted. Do not use compressor until all items have been verified.

WARNING: Risk of bursting. Too much air pressure causes a hazardous risk of bursting. Check the manufacturer’s maximum pressure rating for air tools and accessories. The regulator outlet pressure must never exceed the maximum pressure rating.

Initial Set-up (Fig. 1)

WARNING: Do not operate this unit until you read and understand this instruction manual for safety, operation and maintenance instructions.

BREAK-IN PROCEDURE

CAUTION: Risk of unsafe operation. Be sure compressor is in horizontal position before operating.

CAUTION: Risk of property damage. Serious damage may result if the following break-in instructions are not closely followed.

This procedure is required before the air compressor is put into service for the first time and when the compressor pump/motor has been replaced.

1.Ensure the On/Off switch (L) is in the OFF position.

NOTE: If hose is not connected to Quick Connect body, pull coupler back until it clicks to prevent air from escaping through the quick connect.

2.Plug the power cord into the correct branch circuit receptacle. See Voltage and Circuit Protection under Installation.

3.Open the drain valve (counterclockwise) fully to permit air to escape and prevent air pressure build up in the air tank during the break-in period.

4.Move the On/Off switch to the ON position. The compressor will start.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents D55146 D55146 Air Compressor Pump/Motor SpecificationsSpecifications Declared Noise Emission Values per ISO3744Definitions Safety Guidelines Important Safety InstructionsHOW to Prevent IT Save These InstructionWhat can Happen HOW to Prevent IT Attachments & accessories TiresProperty damage Correct tire pressureEnglish Never defeat the safety fea Attempting to operateTo repair compressor with Can expose you to movingFor Future USE Rized partsNever stand on CompressorFeatures Fig Installation Assembly FigGrounding Instructions Extension CordsVoltage and Circuit Protection Compatibility LocationTransporting LiftingPre-Start Checklist Fig BREAK-IN ProcedurePreparation for USE Initial Set-up FigOperating Procedures MaintenanceFollow Pre-Start Checklist under Preparation for Use Start-up FigMaintenance Chart Checking Safety Valve FigProcedure Daily Weekly Monthly Year or Checking Air Filter Element FigAccessories Service Information Full One Year WarrantyRepairs Date and Place of PurchaseGlossary Troubleshooting Guide Troubleshooting CodesProblem Code Code Possible Cause Possible SolutionUnder Features if pressure drop is excessive While accessory is being usedUsed Extension Cords under Installation Compresseur d’air D55146 Fiche technique de la pompe/du moteurFiche technique Définitions lignes directrices en Matière de sécurité Directives de sécurité importantesConserver CES Directives CE QUI Peut SE Produire Comment L’ÉVITER Avertissement Risque D’ÉCLATEMENTAccessoires PneusLe manomètre pour empêcher un surgonflage Avertissement Risque DE Choc Électrique Mise à la terreÉlectrique le fait de Avertissement Risque Provenant DES Objets Projetés EN L’AIRAvertissement Risque Associé AUX Pièces Mobiles Avertissement Attention Surfaces ChaudesAvertissement Risque Associé À Utilisation Dangereuse Avertissement Risque DE ChuteConserver CES Directives Pour UN Usage Ultérieur CaractéristiquesAvertissement Risque DE Blessure EN Soulevant LE Produit Mise EN Garde Risque Associé AU BruitAssemblage Fig Directives relatives à la mise à la terreRallonges Protection de la tension et du circuitEmplacement CompatibilitéTransport ÉlectricitéMode D’EMPLOI Liste de vérification de pré-démarrage FigRéglage initial Fig Procédure DE RodageProcédures DE Fonctionnement Démarrage Fig Arrêt FigEntretien Programme d’entretien Vérification de la soupape de sûreté FigVérification des éléments du filtre d’air Fig Accessoires Vidange du réservoir d’air FigInformation sur les réparations Réparations Garantie complète d’un 1 anGlossaire Code Cause Possible Solution Possible Guide de dépannageCodes de dépannage Problème CodeIl est normal que la pression chute lorsqu’un accessoi De travail avec l’utilisation de l’accessoire’utilisation de l’accessoire Ne serrez pas tropTion de peinture. Lire lavertissement concernant les vapeurs InflammablesRéparation en usine de Dewalt ou un centre de réparation Agréé DewaltCompresor de aire D55146 Especificaciones de la Bomba y el MotorEspecificaciones Valores de emisión de ruido declarados según ISO3744Instrucciones de seguridad importantes Guarde Estas InstruccionesPeligro Riesgo DE Explosión O Incendio ¿QUÉ Puede SUCEDER?Peligro Riesgo Respiratorio Asfixia Advertencia Riesgo DE Explosión Elementos y accesoriosNeumáticos La presión de éstos antesAdvertencia Riesgo DE Descarga Eléctrica NeumáticoAdvertencia Riesgo DE Objetos Despedidos Advertencia Riesgo DE Superficies CalientesAdvertencia Riesgo POR Piezas Móviles ¿QUÉ Puede SUCEDER?¿QUÉ Puede SUCEDER? Cómo Evitarlo Conserve Estas Instrucciones Para Futuras Consultas Advertencia Riesgo DE Lesión POR Levantar Mucho PesoAdvertencia Riesgo DE Caídas Cómo EvitarloCaracterísticas Fig Instrucciones de conexión a tierra InstalaciónEnsamblaje Fig Cables prolongadores Voltaje y protección del circuitoCompatibilidad Lugar Preparación Para EL USOLista de control previa a la puesta en marcha Fig Configuración inicial Fig Procedimientos Operativos Puesta en marcha FigProcedimiento DE Puesta EN Marcha Inicial Apagado Fig MantenimientoTabla de mantenimiento Controlar la válvula de seguridad FigControlar el elemento del filtro de aire Fig Procedimiento Diaria Semanal Mensual Vez alDrenar el tanque de aire Fig AccesoriosInformación DEL Servicio Técnico ReparacionesGarantía completa de un año VILLAHERMOSA, TABGlosario Guía de detección de problemas Códigos de detección de problemasProblema Código Código Causa Posible Solución PosibleJabonosa. No ajuste demasiado Si la válvula aún pierde, debe ser reemplazadaEs normal que se presente alguna caída de presión cuando AccesorioInstalación Sobre vapor inflamableDel interruptor de presión Page Ewalt Industrial Tool Co., 701 Joppa Road, Baltimore, MD OCT06 Form No. A18765 D55146 Copyright 2006 D Ewalt
Top Page Image Contents