Cisco Systems 2140 Installing a Hard Drive Tray into the Appliance, Removing the Front Bezel

Page 77

Chapter 4 Installing the Cisco ADE 2130 and 2140 Series Appliance Hardware Options

Installing a Hard Drive Tray into the Appliance

Removing the Front Bezel

Note The following procedures assume your Cisco ADE 2130 and 2140 Series appliance came shipped with the front bezel installed.

Remove the front bezel to:

•install or remove hard drives or the optional DVD-ROM drive

•access the front-panel serial (console) port and USB ports

•observe the individual hard disk drive (HDD) activity and fault LEDs

Note The appliance does not need to be powered down to remove the front bezel.

To remove the front bezel:

Step 1 Unfasten the bezel retention screw on the right side of the appliance with a Number 2 Phillips screwdriver.

Step 2 Rotate the bezel outward and detach.

To install the front bezel:

Step 1 Align the four tabs on the left of the bezel with the slots in the front panel and then rotate the free end of the bezel to the closed position.

Step 2 Snap the front bezel into place and tighten the screw at the right side of the bezel.

Installing a Hard Drive Tray into the Appliance

Note The hard drives are hot-swappable. Before removing or replacing a hard drive, you do not need to take the Cisco ADE 2130 and 2140 Series appliance out of service.

Up to six drives can be installed. The hard drive bay is at the left side of the appliance chassis, underneath the DVD-ROM drive. The hard drive trays in the drive bay are labeled 1, 3, and 5 on the left side of the bay and 0, 2, and 4 on the right side of the bay (see Figure 4-2 on page 4-6). The drives need to be installed in a specific order; that is, drive 0 must be installed before drive 1, drive 1 before drive 2, and so on.

Caution If you install fewer than six hard drives, the empty bays must have drive trays with baffles in them to maintain proper appliance cooling.

Cisco Application Deployment Engine (ADE) 2130 and 2140 Series Appliance Hardware Installation Guide

	78-18579-02	4-5

Image 77

Contents Text Part Number Americas HeadquartersCopyright 2008 Cisco Systems, Inc. All rights reserved N T E N T S Lifting Guidelines Preparing Your Site for Installation Powering Up the Cisco ADE 2130 and 2140 Series Appliance Appliance C-2 About This Guide Objectives Document Revision HistoryAudience OrganizationChapter Title Description ConventionsBewaar Deze Instructies Safety WarningsAviso Instruções Importantes DE Segurança Warnung Wichtige SicherheitshinweiseAvvertenza Importanti Istruzioni Sulla Sicurezza Spara Dessa Anvisningar GEM Disse Anvisninger Xiv Related Documentation Obtaining Documentation and Submitting a Service RequestXvi A P T E R Model Product OverviewProduct Serial Number Location Cisco ADE 2130 Series Appliance Cisco ADE 2130 and 2140 Series Appliance ConfigurationsCisco Product Identification Tool Cisco ADE 2140 Series Appliance Specification Description Cisco Spare Part NumberGB Sdram CADE-RAM-25EF= CADE-2U-AC-PSU=Cisco ADE 2130 and 2140 Series Appliance Front View Hardware FeaturesColor State Description Front Control Panel LEDs and SwitchesCisco ADE 2130 and 2140 Series Appliance Rear View SwitchUsed used NIC LEDsAC and DC Power Supply LEDs Ethernet Port NIC 1 and NIC Input/Output Ports and ConnectorsType Description Ethernet Port Pin Signal DescriptionSerial Console Port Signal Description RTS CTS DTR DSR TXD RXD GND RJ-45-to-DB-9 Terminal Adapter ConsoleDC Power Supply Input AC and DC Power SuppliesEnvironmental Monitoring Overtemperature Protection OTPRegulatory Compliance Overcurrent Protection OCPA P T E R General Precautions Safety GuidelinesSafety with Electricity Safety with EquipmentPage Preventing Electrostatic Discharge Damage Site Planning Preparing Your Site for InstallationLifting Guidelines Post Open Rack Rack Installation Safety GuidelinesSite Environment Airflow Guidelines Temperature and Humidity GuidelinesSpecification Minimum Maximum Power ConsiderationsDC Power Supply Safety Considerations Method of ProcedureUnpacking and Checking the Contents of Your Shipment Cisco Part Number Cisco Information Packet and WarrantyReplacement, Repair, or Refund Policy for Hardware Duration of Hardware WarrantyTo Receive a Return Materials Authorization RMA Number Required Tools and EquipmentTask Verified by Date Installation ChecklistCreating a Site Log Serial Console Port Connections Ethernet and Console Port ConsiderationsNIC 1 and NIC 2 RJ-45 Ethernet Connections 78-18579-02 Page Installing the Cisco ADE 2130 and 2140 Series Appliance Rack-Mounting Configuration Guidelines Installing the Cisco ADE 2130 and 2140 Series Appliance 2-Post Rack-Mount Kit Post Rack-Mount Hardware KitAttaching the L Brackets to the Appliance Mid-Mounting in a 2-Post RackAttaching an L Bracket to a Center Post Installing the Appliance in the Rack4-post Rails and Brackets Item No Description Quantity Attaching the Inner Slide Rails to the ApplianceAttaching the Outer Slide Rails to the Rack Installing the Appliance into the RackInstalling Appliance into Rack Cisco ADE 2130 and 2140 Series Appliance Power Connecting the Appliance AC Power Grounding the Rack Connecting the Appliance DC Power and GroundPower Connections Grounding Connections 10 Stripping the Ground Wire Wiring the DC-Input Power Source 12 Stripping the Power Wire Connecting the Network Interface Connecting the Network and Console CablesCable Management Connecting the ConsolePower-Up Procedure AC Power Supply Powering Up the Cisco ADE 2130 and 2140 Series ApplianceChecking the LEDs Power-Up Procedure DC Power SupplyADE 2130 and 2140 Appliance Front-Panel LEDs A P T E R Before You Begin Preparing for a Successful InstallationHardware Options Description Cisco Spare Part NumberRemoving the Cover Beginning the InstallationTools and Supplies Needed Removing the Cisco ADE 2130 and 2140 Series Appliance Cover Removing the Front Bezel Installing a Hard Drive Tray into the ApplianceRemoving the Hard Drive Tray Removing the Processor Air Duct Removing and Installing the Processor Air DuctTo remove the processor air duct Installing the Processor Air Duct Installing and Removing MemoryBranch Channel B Channel a Installing DIMMs Installing DIMMsRemoving DIMMs Removing and Installing the PCI Adapter CardConfiguration Lower Slot Upper Slot Configuration Bottom Slot Middle Slot Top SlotPCI riser assembly Pins Removing the PCI Riser AssemblyRemoving a Full-Height Adapter Card Removing a PCI Adapter CardInstalling a PCI Adapter Card Installing the PCI Riser Assembly Installing or Replacing a Power SupplyAC and DC Power Supply Modules Replacing a Redundant Power SupplyAdding a New Redundant Power Supply Replacing a Nonredundant Power SupplyInstalling the Cover Completing the Installation231198 Page Troubleshooting Overview TroubleshootingProblem Solving Environmental Reporting Features Troubleshooting the Power and Cooling SystemsTroubleshooting Adapter Cards, Cables, and Connections Front-Panel LEDs Reading the LEDsFigure A-2 NIC 1 and NIC 2 LEDs NIC LEDsCisco Product Identification Tool Product Serial Number LocationPage Site Log Initials DateMaintaining Your Site Environment Maintaining the Cisco ADE 2130 ApplianceCables and Connectors General Exterior Cleaning and InspectionAppliance Adapter CardsCooling TemperatureAltitude HumidityElectrostatic Discharge Electromagnetic and Radio Frequency InterferenceMagnetism Power Source InterruptionsPage Numerics EMI See ESDNIC See MOPRFI Preventing effects RJ-45 pinout NIC Safety guidelinesIN-5 IN-6