Cisco Systems 2130, 2140 manual Installing a PCI Adapter Card

Page 88

Chapter 4 Installing the Cisco ADE 2130 and 2140 Series Appliance Hardware Options

Removing and Installing the PCI Adapter Card

1

Rear retention screw

4

Rear retention screw

 

 

 

 

2

Front retention clip

5

Adapter card

 

 

 

 

3

Adapter card

 

 

 

 

 

 

Step 8 When removing a full-height adapter card, remove the front retention clip by loosening the blue captive screw and rotating the clip outward. (See location 2 in Figure 4-8 on page 4-15.)

Step 9 Disengage the three plastic tabs from the metal sidewall.

Step 10 Remove the adapter card from the PCI slot. (See item 3 or 5 in Figure 4-8 on page 4-15).

Installing a PCI Adapter Card

To install a PCI adapter card in the riser card assembly:

Step 1 Review the information in the “Safety Warnings” section on page x and the “Safety Guidelines” section on page 2-2.

Step 2 Power down the appliance and all external devices. Disconnect the AC power cord or DC power source and all external cables.

Step 3 Attach the antistatic wrist strap to your wrist and connect its cord to the ESD socket on the top, left-hand side on the front of the appliance.

Step 4 Remove the appliance cover. For instructions, see the “Removing the Cover” section on page 4-3. Step 5 Disconnect any cables attached to any adapter cards.

Step 6 Remove the PCI riser assembly. For instructions, see the “Removing the PCI Riser Assembly” section on page 4-14. Then, turn the riser adapter card assembly upside down to remove the adapter card.

Step 7 If the adapter card slot was empty before installing the new card, remove the adapter card filler panel.

Step 8 For a full-height adapter card, remove the front retention clip by loosening the blue captive thumbscrew and rotating the clip outward (see location 2 in Figure 4-8 on page 4-15). Then, disengage the three plastic tabs from the metal sidewall.

Step 9 With the riser card assembly upside down, slide the adapter card onto the sheet metal and attach it to the appropriate riser card connector. Be sure that the adapter card edge connector is seated in the riser card connector correctly.

Step 10 Fasten the adapter card to the riser card assembly bracket using the rear retention screw (see location 1 or 4 in Figure 4-8 on page 4-15) and, for full-height cards, by also replacing the front retention clip and tightening the captive thumbscrew. (See location 2 in Figure 4-8 on page 4-15.)

Step 11 Install the PCI riser assembly into the appliance. For instructions, see the “Installing the PCI Riser Assembly” section on page 4-17on this page.

Step 12 Install the appliance cover. For instructions, see the “Installing the Cover” section on page 4-20. Step 13 Plug all peripheral devices and the AC power cable or DC power source into the appliance.

Cisco Application Deployment Engine (ADE) 2130 and 2140 Series Appliance Hardware Installation Guide

4-16

78-18579-02

 

 

Page 87 Page 89
Image 88
Page 87 Page 89
Contents Americas Headquarters Text Part NumberCopyright 2008 Cisco Systems, Inc. All rights reserved N T E N T S Lifting Guidelines Preparing Your Site for Installation Powering Up the Cisco ADE 2130 and 2140 Series Appliance Appliance C-2 About This Guide Document Revision History ObjectivesAudience OrganizationConventions Chapter Title DescriptionSafety Warnings Bewaar Deze InstructiesAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseAviso Instruções Importantes DE Segurança Spara Dessa Anvisningar GEM Disse Anvisninger Xiv Obtaining Documentation and Submitting a Service Request Related DocumentationXvi A P T E R Product Overview ModelProduct Serial Number Location Cisco Product Identification Tool Cisco ADE 2130 and 2140 Series Appliance ConfigurationsCisco ADE 2130 Series Appliance Specification Description Cisco Spare Part Number Cisco ADE 2140 Series ApplianceGB Sdram CADE-RAM-25EF= CADE-2U-AC-PSU=Hardware Features Cisco ADE 2130 and 2140 Series Appliance Front ViewFront Control Panel LEDs and Switches Color State DescriptionSwitch Cisco ADE 2130 and 2140 Series Appliance Rear ViewNIC LEDs Used usedAC and DC Power Supply LEDs Input/Output Ports and Connectors Ethernet Port NIC 1 and NICSerial Console Port Ethernet Port Pin Signal DescriptionType Description Signal Description RJ-45-to-DB-9 Terminal Adapter Console RTS CTS DTR DSR TXD RXD GNDAC and DC Power Supplies DC Power Supply InputOvertemperature Protection OTP Environmental MonitoringRegulatory Compliance Overcurrent Protection OCPA P T E R Safety Guidelines General PrecautionsSafety with Equipment Safety with ElectricityPage Preventing Electrostatic Discharge Damage Lifting Guidelines Preparing Your Site for InstallationSite Planning Rack Installation Safety Guidelines Post Open RackSite Environment Temperature and Humidity Guidelines Airflow GuidelinesPower Considerations Specification Minimum MaximumMethod of Procedure DC Power Supply Safety ConsiderationsUnpacking and Checking the Contents of Your Shipment Cisco Information Packet and Warranty Cisco Part NumberDuration of Hardware Warranty Replacement, Repair, or Refund Policy for HardwareTo Receive a Return Materials Authorization RMA Number Required Tools and EquipmentCreating a Site Log Installation ChecklistTask Verified by Date NIC 1 and NIC 2 RJ-45 Ethernet Connections Ethernet and Console Port ConsiderationsSerial Console Port Connections 78-18579-02 Page Installing the Cisco ADE 2130 and 2140 Series Appliance Rack-Mounting Configuration Guidelines Installing the Cisco ADE 2130 and 2140 Series Appliance Post Rack-Mount Hardware Kit 2-Post Rack-Mount KitMid-Mounting in a 2-Post Rack Attaching the L Brackets to the ApplianceInstalling the Appliance in the Rack Attaching an L Bracket to a Center Post4-post Rails and Brackets Attaching the Inner Slide Rails to the Appliance Item No Description QuantityInstalling the Appliance into the Rack Attaching the Outer Slide Rails to the RackInstalling Appliance into Rack Cisco ADE 2130 and 2140 Series Appliance Power Connecting the Appliance AC Power Power Connections Connecting the Appliance DC Power and GroundGrounding the Rack Grounding Connections 10 Stripping the Ground Wire Wiring the DC-Input Power Source 12 Stripping the Power Wire Connecting the Network and Console Cables Connecting the Network InterfaceConnecting the Console Cable ManagementPowering Up the Cisco ADE 2130 and 2140 Series Appliance Power-Up Procedure AC Power SupplyPower-Up Procedure DC Power Supply Checking the LEDsADE 2130 and 2140 Appliance Front-Panel LEDs A P T E R Preparing for a Successful Installation Before You BeginHardware Options Description Cisco Spare Part NumberTools and Supplies Needed Beginning the InstallationRemoving the Cover Removing the Cisco ADE 2130 and 2140 Series Appliance Cover Installing a Hard Drive Tray into the Appliance Removing the Front BezelRemoving the Hard Drive Tray Removing and Installing the Processor Air Duct Removing the Processor Air DuctTo remove the processor air duct Installing and Removing Memory Installing the Processor Air DuctBranch Channel B Channel a Installing DIMMs Installing DIMMsRemoving and Installing the PCI Adapter Card Removing DIMMsConfiguration Bottom Slot Middle Slot Top Slot Configuration Lower Slot Upper SlotRemoving the PCI Riser Assembly PCI riser assembly PinsRemoving a PCI Adapter Card Removing a Full-Height Adapter CardInstalling a PCI Adapter Card Installing or Replacing a Power Supply Installing the PCI Riser AssemblyReplacing a Redundant Power Supply AC and DC Power Supply ModulesReplacing a Nonredundant Power Supply Adding a New Redundant Power SupplyCompleting the Installation Installing the Cover231198 Page Troubleshooting Troubleshooting OverviewProblem Solving Troubleshooting the Power and Cooling Systems Environmental Reporting FeaturesTroubleshooting Adapter Cards, Cables, and Connections Reading the LEDs Front-Panel LEDsNIC LEDs Figure A-2 NIC 1 and NIC 2 LEDsProduct Serial Number Location Cisco Product Identification ToolPage Site Log Date InitialsMaintaining the Cisco ADE 2130 Appliance Maintaining Your Site EnvironmentGeneral Exterior Cleaning and Inspection Cables and ConnectorsAppliance Adapter CardsTemperature CoolingHumidity AltitudeElectrostatic Discharge Electromagnetic and Radio Frequency InterferencePower Source Interruptions MagnetismPage Numerics See ESD EMISee MOP NICPreventing effects RJ-45 pinout NIC Safety guidelines RFIIN-5 IN-6
Top Page Image Contents