Southbend SB1040 owner manual SB1041 Circuit Requirements, Grounding Requirements

Page 16

Model SB1040/SB1041

P R E P A R A T I O N

For Machines Mfg. Since 8/09

SB1041 Circuit Requirements

This machine is prewired to operate on a 220V power supply circuit that has a verified ground and meets the following requirements:

Nominal Voltage

220V

Cycle

60 Hz

Phase

3-Phase

Circuit Rating

15 Amps

Plug/Receptacle Type

Hardwire

Grounding Requirements

In the event of certain types of malfunctions or breakdowns, grounding provides a path of least resistance for electric current—in order to reduce the risk of electric shock.

For 110V Connection (SB1040 Prewired)

This machine is equipped with a power cord that has an equipment-grounding wire and a grounding plug (similar to the figure below). The plug must only be inserted into a matching receptacle (outlet) that is properly installed and grounded in accordance with all local codes and ordinances.

GROUNDED

5-15 RECEPTACLE

Grounding Prong

5-15 PLUG

Current Carrying Prongs

Figure 1. NEMA 5-15 plug and receptacle.

For 220V 1-Phase Connection (SB1040)

Use the plug type listed in the Circuit Requirements for this voltage. The listed plug (similar to the figure below) has an equipment- grounding wire to safely ground the machine. The plug must only be inserted into a matching receptacle (outlet) that is properly installed and grounded in accordance with all local codes and ordinances.

GROUNDED

6-15 RECEPTACLE

Current Carrying Prongs

6-15 PLUG

Grounding Prong

Figure 2. NEMA 6-15 plug and receptacle.

For 220V 3-Phase Connection (SB1041)

Power supply connections that are hardwired to the power source must be connected to a grounded metal permanent wiring system, or to a system having an equipment-grounding conductor.

 

LOCKING

DISCONNECT SWITCH

Power Source

Machine

Conduit

Conduit

Ground

Ground

Figure 3. Typical hardwire setup.

Serious injury could occur if you connect the machine to power before completing the setup process. DO NOT connect to power until instructed later in this manual.

-14-

Image 16
Contents Metal Cutting Bandsaw Updates Customer ServiceScope of Manual Manual FeedbackTable of Contents Service About This Machine FeaturesCapabilities Identification FPMMachine Specifications 012 3345-4&6@1% !1 +++ 012 34-4&6 5C= Basic Machine Safety Understanding Risks of MachineryF E T Y Additional Metal Cutting Bandsaw Safety Preparation Overview Things Youll NeedPower Supply Requirements AvailabilityFull-Load Current Rating Circuit InformationFor 110V Connection SB1040 Prewired For 220V 1-Phase Connection SB1040For 220V 3-Phase Connection SB1041 SB1041 Circuit RequirementsInventory UnpackingExtension Cords Before cleaning, gather the following Cleaning & ProtectingBasic steps for removing rust preventative Location Securing to Floor Lifting & MovingBolting to Concrete Floors Initial Lubrication AssemblyMachine Mounts Power Connection Correcting Phase Polarity SB1041 OnlyTo correct the polarity of a power source connection 220V Conversion for SB1040Test Run Inspections AdjustmentsTo test run your machine Operation Overview Grinder Switch Turns grinder ON/OFF ControlsBlade Selection Blade LengthBlade Terminology Blade WidthTooth Set Tooth TypeBlade Pitch TPI To select the correct blade pitchBlade Changes Blade TensionTo replace the blade To correctly tension the bladeBlade Breakage Blade Care & Break-InBlade Care Blade Break-InBlade Speed Chart Chip Inspection ChartAdjusting Blade Guides To properly adjust the upper and lower blade guidesPositioning Guide Post To properly position the guide postLower blade guides and bracket Tilting Table Blade WeldingTo tilt the table left or right To tilt the table forward or backwardAbove 3⁄8 Blade ⁄4-3⁄8 Blade Correct Not Correct Correct Not Correct Cut and reweld Circle Cutting Jig To use the circle cutting jigCleaning Maintenance ScheduleDressing Grinding Wheel Lubrication Upper wheel leadscrew lubricationBelts Dressing Rubber TiresSprocket Drive Belt Air Pump BeltMachine Storage To adjust the upper wheel for blade tracking Blade TrackingTable Calibration To calibrate the table to zeroGuide Post Alignment To align the guide postTo adjust the leadscrew collars to reduce backlash Bevel Gear BacklashLeadscrew End Play To reduce the bevel gear backlashTroubleshooting Symptom Possible Cause Possible SolutionPolarity on TR O U B L E S H O OTI N G Dull blade missing teeth Replace blade Electrical Safety Instructions Wiring Overview Wiring Diagram Color KEYSB1040/SB1041 Control Panel/Welding Unit WELDER’S Lamp Welding UnitSB1040 110V Electrical Panel, Motor & Cord Electrical PanelSB1040 220V Electrical Panel, Motor & Cord SB1041 220V Electrical Panel, Motor & Cord Electrical Component Pictures Motor and FPM sensor Terminal Strip Welding TransformerFrame BottomBottom Frame Parts List DescriptionDrivetrain SB1040 OnlyDrive Train Parts List Motor Cord SB1041Top Frame Top Frame Parts List 302 Welding Station & Control Panel SB1040/SB1041Welding Station & Control Panel Parts List Digital Tachometer System Electrical Cabinet Terminal Block 4 Post615 618 612 611 619 613 614 621 620 617 616 626 624 622 Machine Labels 702 703T E S Warranty #JB13203