DeWalt DWE7480 instruction manual Push Block, Bevel Ripping Fig, Bevel Crosscutting, Mitering

Page 13
FIG. 40
FIG. 39

Push Block (Fig. 36, 37)

IMPORTANT: Only use the push block (A12) with the narrow rip auxiliary fence. Refer to Narrow Rip Auxiliary Fence. The push block should be used once the material being cut reaches the saw table top.

1.Construct a push block using the diagram in Figure 36. NOTE: Edges (A15) must be the same size.

IMPORTANT: The over hanging edge (A16, Fig. 36) MUST be square. An uneven lip could cause the push block to slip or push the material away from the fence.

2.Place the push block (A12, Fig. 37) behind the material and ensure the lip of the block is flush to the narrow rip auxiliary fence (A13).

3.Once the push block is in place, continue feeding the material until the cut is complete making sure the push block remains flush to the narrow rip auxiliary fence at all times.

IMPORTANT: The narrow rip auxiliary fence and the over hanging edge (A16, Fig. 36) should both be the same thickness.

WARNING: Use caution when starting the cut to prevent binding of the guard against the workpiece resulting in damage to saw and possible injury.

CAUTION: When using a block as a cut-off gauge, the block must be at least 3/4" (19 mm) thick and is very important that the rear end of the block be positioned so the workpiece is clear of the block before it enters the blade to prevent contact with blade resulting in a thrown workpiece and possibly injury.

1.Remove the rip fence and place the miter gauge in the desired slot.

2.Adjust the blade height so that the blade is about 1/8" (3.2 mm) higher than the top of the workpiece.

3. Hold the workpiece firmly against the miter gauge with the path of the blade in line with the desired cut location. Keep the workpiece an inch or so in front of the blade. KEEP BOTH HANDS AWAY FROM THE BLADE AND THE PATH OF

English

FIG. 37

Bevel Ripping (Fig. 38)

This operation is the same as ripping except the bevel angle is set to an angle other than zero degrees.

WARNING: Before connecting the table saw to the power source or operating the saw, always inspect the blade guard assembly and riving knife for proper alignment and clearance with saw blade. Check alignment after each change of bevel angle.

Crosscutting

WARNING: NEVER touch the free

A12

A13

FIG. 38

THE BLADE (Fig. 39).

4. Start the saw motor and allow the blade to come up to speed.

5. While using both hands to keep the workpiece against the face of the miter gauge, and holding the workpiece flat against the table, slowly push the workpiece through the blade. Refer to Figure 38.

6.Never try to pull the workpiece with the blade turning. Turn the switch off, allow the blade to stop, and carefully slide the workpiece out.

CAUTION: Never touch or hold onto the free or cut off end of the workpiece.

Bevel Crosscutting

This operation is the same as crosscutting except that the bevel angle is set to an angle other than 0°. For proper hand position, refer to Figure 38.

WARNING: Before connecting the table saw to the power source or operating the saw, always inspect the blade guard assembly and riving knife for proper alignment and clearance with saw blade. Check alignment after each change of bevel angle.

Mitering

WARNING: Miter angles greater than 45˚ may force the blade guard assembly into the saw blade causing damage to the blade guard assembly and personal injury. Before starting the motor, test the operation by feeding the workpiece into the blade guard assembly. If the blade guard assembly contacts the blade, place the workpiece under the blade guard assembly, not touching the blade,

end of the workpiece or a free piece that is cut off, while the power is ON and/or the saw blade is rotating. Piece may contact the blade resulting in a thrown workpiece and possible injury. WARNING: To reduce the risk of injury, NEVER use the fence as a guide or length stop when crosscutting.

WARNING: NEVER use a length stop on the free end of the workpiece when crosscutting. In short, the cut-off piece in any thru sawing (cutting completely through the workpiece) operation must never be confined — it must be allowed to move away from saw blade to prevent contact with blade resulting in a thrown workpiece and possibly injury.

before starting the motor.

CAUTION: Certain workpiece shapes, such as molding may not lift

the blade guard assembly properly. Feed the workpiece slowly to start the cut. If the blade guard assembly contacts the blade, place the workpiece under the blade guard assembly, not touching the blade, before starting the motor.

This operation is the same as crosscutting except the miter gauge is locked at an angle other than 0°. Hold the workpiece FIRMLY against the miter gauge and feed the workpiece slowly into the blade (to prevent the workpiece from moving). Refer to Figure 40.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Dewalt General Safety Rules Double Insulation Definitions Safety GuidelinesImportant Safety Instructions Polarized PlugsAlways lock the fence and bevel adjustment before cutting Additional Safety Rules for Table SawsMaking a Push Stick Inside Back Cover How to Avoid Them and Protect Yourself from Possible InjuryKickbacks For Future USE Features FigSpecifications UnpackingAssembling the Rip Fence Fig AssemblyTo Remove the Throat Plate Fig Positioning the Riving Knife FigBlade Guard Assembly Anti-Kickback Assembly FigMiter Gauge Fig Bench MountingOn-Off Switch Fig Connecting Saw to Power SourceAdjustments Rip Fence OperationBevel Lock Adjustment FIG Fence Alignment AdjustmentPart a Adjusting the Bevel Scale System Part B Adjusting the Bevel Scale Pointer Blade , 6, 27 Blade Guard Assembly and To Remove the Throat Plate under Saw Blades Riving Knife SelectionKickback Guard Operating Feature FigOperation Kickback is a dangerous condition! It is caused byRipping Small Pieces RippingNarrow Rip Auxiliary Fence Fig Bevel Ripping Fig Push BlockCrosscutting Bevel CrosscuttingCompound Mitering Miter Gauge OperationFeatherboard Construction Dust CollectionMaintenance Three Year Limited WarrantyCleaning Accessories Repairs Register OnlineRègles de sécurité Généralités Définitions Consignes de sécuritéConserver CES Consignes Double isolationFrançais Français Fiche technique Conserver CES Consignes Pour Utilisation UltérieureDésemballage RebondsAssemblage CaractéristiquesPour Réinstaller La Plaque De Lumière Fig Installation du Guide Longitudinal FigPour Retirer la Plaque De Lumière Fig Positionnement Du Couteau Diviseur FigDispositif de carter de lame Montage Sur Établi Guide d’onglet FigBranchement de la scie Fixation DU Guide D’ONGLETFonctionnement du guide longitudinal Interrupteur Marche/Arrêt FigRéglages Partie a Réglage du système de graduation de chanfrein Réglage DU Dispositif DE Blocage DE Biseau FIGAlignement DU Couteau Diviseur ET DE LA Lame FIG Lames de scieSection Retrait de la plaque de lumière sous FIG MontageRebonds Choix du couteau diviseurFonctionnement Coupes longitudinales Caractéristiques du dispositif de protection FigCoupes longitudinales de petites pièces Guide longitudinal auxiliaire étroit Fig Bloc-poussoirCoupes transversales Sciage sur le long En biseau FigTronçonnage en biseau OngletStockage LubrificationDépoussiérage Entretien Reglas de Seguridad Generales Definiciones Lineamientos de SeguridadGuarde Estas Instrucciones Doble AislamientoReglas de Seguridad Adicionales para Sierras de Banco Bloquee Siempre la guía y el ajuste de bisel antes de cortar Desembalaje Guarde Estas Instrucciones Para Futuras ConsultasRebotes Cómo evitarlos y Protegerse de Posibles LesionesCaracterísticas Fig AdjustmentEnsamblaje Ensamble SU Sierra EN EL Siguiente OrdenDesensamblaje de la placa de garganta Fig Montaje de la guía para cortes longitudinales FigPosicionamiento De La Cuchilla Fig Cambio De La Placa De Garganta FigEnsamble Protector de la Hoja Calibrador de inglete FigMontaje en el banco de trabajo Conexión de la sierra a la fuente de alimentaciónFuncionamiento de la guía de corte longitudinal Interruptor de Encendido/ apagado FigAjustes Escala Para Cortes Longitudinales en laParte a Ajuste del Sistema de la Escala de Bisel Ajuste DEL Bloqueo DEL Bisel FIGParte B Ajuste del Indicador de Escala de Bisel De la Placa de Garganta en Ensamblaje Hoja , 6, 27Más elevada. Ver Posicionamiento de la Del Ensamble Protector de laRebote Selección de CuchillaOperación Ranurado Función de Operación del Protector FigIniciar el Corte Cuando queden Bloque de Empuje Ranurando Piezas PequeñasGuía Auxiliar Para Cortes Delgados Fig Resulta inseguro ranurar piezasCortes transversales en bisel Ranurado de Bisel FigInglete Corte CruzadoColector de polvo LubricaciónAlmacenamiento Acople la vara de empuje U a la guíaLimpieza MantenimientoAccesorios ReparacionesGarantía limitada por tres años Registro en líneaAÑO DE Servicio Gratuito Garantía DE Reembolso DE SU Dinero POR 90 DíasPage Page Page Largeur ou un peu moins large que la pièce à
Top Page Image Contents