DeWalt DWE7480 Miter Gauge Operation, Compound Mitering, Featherboard Construction, Lubrication

Page 14

English

Miter Gauge Operation

To set your miter gauge, loosen the lock handle and move the miter gauge to the desired angle.

Compound Mitering

This is a combination of bevel crosscutting and mitering. Follow the instructions for both bevel crosscutting and mitering.

Featherboard Construction

Featherboards are used to keep the work in contact with the fence and table, and help prevent kickbacks. Dimensions for making a typical featherboard are shown in Fig. 41. Make the featherboard from a straight piece of wood that is free of knots and cracks. Clamp the featherboard to the fence and table so that the leading edge of the featherboard will support the workpiece until the cut is complete (Fig. 42). An 8" (203 mm) high flat board can be clamped to the rip fence and the featherboard can be clamped to the 8" (203 mm) high board.

FIG. 41

Dust Collection

Your table saw is equipped with a dust shroud and dust collection port. For best results, connect a vacuum to the port at the rear of the saw.

After extended use, the saw’s dust collection system may become clogged. To clear the dust collection system:

1.Unplug the saw.

2.Turn the saw on its side, so the bottom, open part of the unit is accessible.

3.Open the dust access door (UU) shown in Figure 43 by removing the wing screws (V V). Clean out the excess dust, and re-secure the access door with the wing screws.

FIG. 43

UU

V V

FIG. 44

 

24" (610 mm)

 

3/4"

 

(20 mm)

 

THE KERF

4"

SHOULD BE

ABOUT 1/4"

(102 mm)

(6.4 mm) APART

 

5" (127 mm)

WARNING: Use featherboards for all non-thru sawing operations where the blade guard assembly, anti-kickback assembly and riving knife cannot be used. Always replace the blade guard assembly, anti-kickback assembly and riving knife when the non-thru sawing operation is complete. Make sure the featherboard presses only on the portion of the workpiece in front of the blade.

FIG. 42

Lubrication

1. All motor bearings are permanently lubricated at the factory and no additional lubrication is needed.

2. The height adjustment gear may require periodic cleaning and lubrication (Fig. 44). If you have difficulty raising or lowering the blade, contact a DEWALT authorized service center.

U

FIG. 46

Q

FF

V

D

STORAGE (Fig. 45, 46)

1.Attach push stick (U) to fence.

2.Remove blade guard assembly (D). Refer to To Remove Blade Guard Assembly. Slide blade guard assembly into brackets as shown.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Dewalt Important Safety Instructions Definitions Safety GuidelinesGeneral Safety Rules Double Insulation Polarized PlugsAdditional Safety Rules for Table Saws Always lock the fence and bevel adjustment before cuttingKickbacks How to Avoid Them and Protect Yourself from Possible InjuryMaking a Push Stick Inside Back Cover Specifications Features FigFor Future USE UnpackingTo Remove the Throat Plate Fig AssemblyAssembling the Rip Fence Fig Positioning the Riving Knife FigMiter Gauge Fig Anti-Kickback Assembly FigBlade Guard Assembly Bench MountingAdjustments Connecting Saw to Power SourceOn-Off Switch Fig Rip Fence OperationPart a Adjusting the Bevel Scale System Fence Alignment AdjustmentBevel Lock Adjustment FIG Part B Adjusting the Bevel Scale PointerSaw Blades Blade Guard Assembly and To Remove the Throat Plate underBlade , 6, 27 Riving Knife SelectionOperation Guard Operating Feature FigKickback Kickback is a dangerous condition! It is caused byNarrow Rip Auxiliary Fence Fig RippingRipping Small Pieces Crosscutting Push BlockBevel Ripping Fig Bevel CrosscuttingFeatherboard Construction Miter Gauge OperationCompound Mitering Dust CollectionCleaning Accessories Repairs Three Year Limited WarrantyMaintenance Register OnlineConserver CES Consignes Définitions Consignes de sécuritéRègles de sécurité Généralités Double isolationFrançais Français Désemballage Conserver CES Consignes Pour Utilisation UltérieureFiche technique RebondsCaractéristiques AssemblagePour Retirer la Plaque De Lumière Fig Installation du Guide Longitudinal FigPour Réinstaller La Plaque De Lumière Fig Positionnement Du Couteau Diviseur FigBranchement de la scie Guide d’onglet FigDispositif de carter de lame Montage Sur Établi Fixation DU Guide D’ONGLETRéglages Interrupteur Marche/Arrêt FigFonctionnement du guide longitudinal Réglage DU Dispositif DE Blocage DE Biseau FIG Partie a Réglage du système de graduation de chanfreinSection Retrait de la plaque de lumière sous FIG Lames de scieAlignement DU Couteau Diviseur ET DE LA Lame FIG MontageFonctionnement Choix du couteau diviseurRebonds Coupes longitudinales de petites pièces Caractéristiques du dispositif de protection FigCoupes longitudinales Bloc-poussoir Guide longitudinal auxiliaire étroit FigTronçonnage en biseau Sciage sur le long En biseau FigCoupes transversales OngletDépoussiérage LubrificationStockage Entretien Guarde Estas Instrucciones Definiciones Lineamientos de SeguridadReglas de Seguridad Generales Doble AislamientoReglas de Seguridad Adicionales para Sierras de Banco Bloquee Siempre la guía y el ajuste de bisel antes de cortar Rebotes Guarde Estas Instrucciones Para Futuras ConsultasDesembalaje Cómo evitarlos y Protegerse de Posibles LesionesEnsamblaje AdjustmentCaracterísticas Fig Ensamble SU Sierra EN EL Siguiente OrdenPosicionamiento De La Cuchilla Fig Montaje de la guía para cortes longitudinales FigDesensamblaje de la placa de garganta Fig Cambio De La Placa De Garganta FigMontaje en el banco de trabajo Calibrador de inglete FigEnsamble Protector de la Hoja Conexión de la sierra a la fuente de alimentaciónAjustes Interruptor de Encendido/ apagado FigFuncionamiento de la guía de corte longitudinal Escala Para Cortes Longitudinales en laParte B Ajuste del Indicador de Escala de Bisel Ajuste DEL Bloqueo DEL Bisel FIGParte a Ajuste del Sistema de la Escala de Bisel Más elevada. Ver Posicionamiento de la Hoja , 6, 27De la Placa de Garganta en Ensamblaje Del Ensamble Protector de laOperación Selección de CuchillaRebote Iniciar el Corte Cuando queden Función de Operación del Protector FigRanurado Guía Auxiliar Para Cortes Delgados Fig Ranurando Piezas PequeñasBloque de Empuje Resulta inseguro ranurar piezasInglete Ranurado de Bisel FigCortes transversales en bisel Corte CruzadoAlmacenamiento LubricaciónColector de polvo Acople la vara de empuje U a la guíaAccesorios MantenimientoLimpieza ReparacionesAÑO DE Servicio Gratuito Registro en líneaGarantía limitada por tres años Garantía DE Reembolso DE SU Dinero POR 90 DíasPage Page Page Largeur ou un peu moins large que la pièce à
Top Page Image Contents