Black & Decker FS210LS instruction manual Troubleshooting Guide, WHAT’S WRONG? What to DO…

Page 27

TROUBLESHOOTING GUIDE

BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS

TROUBLE! SAW WILL NOT START
WHAT’S WRONG?	WHAT TO DO…
1.Saw not plugged in.	1.Plug in saw.
2.Fuse blown or circuit breaker tripped.	2.Replace fuse or reset
	circuit breaker.
3.Cord damaged.	3.Have cord replaced by
	authorized service center.
4.Brushes worn out.	4.Have brushes replaced
	by authorized service center.
TROUBLE! SAW MAKES UNSATISFACTORY CUTS
WHAT’S WRONG?	WHAT TO DO…
1.Dull blade.	1.Replace blade.
2.Blade mounted backwards.	2.Turn blade around.
3.Gum or pitch on blade.	3.Remove blade and
	clean with turpentine.
4.Incorrect blade for work being done.	4.Change the blade.
TROUBLE! BLADE DOES NOT COME UP TO SPEED
WHAT’S WRONG?	WHAT TO DO…
1.Extension cord too light or too long.	1.Replace with adequate
	size cord.
2.Low house current.	2.Contact your electric
	company.
TROUBLE! MACHINE VIBRATES EXCESSIVELY
WHAT’S WRONG?	WHAT TO DO…
1.Stand on uneven floor.	1.Reposition on flat level
	surface.
2.Damaged saw blade.	2.Replace blade.
TROUBLE! DOES NOT MAKE ACCURATE MITER CUTS
WHAT’S WRONG?	WHAT TO DO…
1.Miter scale not adjusted correctly.	1.Check and adjust.
2.Blade is not square to fence.	2.Check and adjust.
3.Blade is not perpendicular to table.	3.Check and adjust fence.
4.Workpiece moving.	4.Clamp workpiece to
	fence or glue 120 grit
	sandpaper to fence with
	rubber cement.
TROUBLE! MATERIAL PINCHES BLADE
WHAT’S WRONG?	WHAT TO DO…
1.Cutting bowed material.	1. Position bowed material
	with concave or hollow side down.
2.Rip fence not parallel to blade.	2. Realign rip fence.
TROUBLE! CANNOT LOCK BLADE INTO BEVEL POSITION
WHAT’S WRONG?	WHAT TO DO…
1.Blade tilting lock handle too loose.	1.Remove blade raising and lowering with
	handwheel.
	2. Remove flat head screw from lock handle.
	3. Tighten blade tilting lock handle. The lock

handle (A) is spring-loaded and can be repositioned by pulling out on the handle (A) and repositioning it on the serrated stud located underneath the handle. NOTE: After tightening, place the handle at the one o’clock position.

4. Replace the flat head screw.

27

Image 27

Contents FS210LS 10 Table SAW Safety Guidelines Definitions General Safety RulesImportant Safety Instructions Stay ALERT, Watch What YOU are DOING, Failure to Follow These Rules MAY Result in Serious InjuryAdditional Safety Rules for Table Saws Power Connections Motor SpecificationsGrounding Instructions Extension Cords Functional DescriptionForeword Assembly Time Estimate Unpacking and CleaningAssembly Assembly Tools RequiredMiter Gage Holder Parts 19,20,21,22,23,24,25 RIP Fence Parts 11,12Stand Parts Miter Gage Holder Disconnect Machine from Power SourceEB D Stand AssemblyAttaching Dust BAG SAW to StandAssembling Blade Raising and Lowering Handwheel At this time Blade Guard Splitter AssemblyPage Guide Rail to SAW Extension WingsMiter Gage RIP FenceOutfeed Support Blade Raising Lowering Control Operating Controls and AdjustmentsLocking Switch in the OFF Position Starting and Stopping SAWBlade Tilting Control Adjusting 90 and 45 Degree Positive StopsTo Adjust Positive Stop AT 90 Degrees To Adjust Positive Stop AT 45 DegreesRIP Fence Operation Adjustments Miter Gage Operation and AdjustmentsC BD Changing the Blade Adjusting Blade Parallel to Miter Gage SlotsNever USE the Fence AS a CUT-OFF Gage When CROSS-CUTTING Common Sawing OperationsCROSS-CUTTING Constructing a Push Stick RippingAccessory Dado Cutterhead Using Auxiliary Woodfacing on RIP FenceAttach the dado head set D , to the saw arbor Constructing a Featherboard WHAT’S WRONG? What to DO… Troubleshooting GuideConstructing a Push Stick Push StickAccessories Scie À Table DE 254 MM Lignes Directrices EN Matière DE Sécurité Définitions Règles Générales DE SécuritéDirectives DE Sécurité Importantes Retirer LES Clés ET LES Clés DE Réglage Pour Éviter L’EFFET DE Rebond Règles DE Sécurité Supplémentaires Pour LES Scies DE TableConnexions Électriques Caractéristiques Techniques DU MoteurDirectives DE Mise À LA Terre Rallonges Description FonctionnelleAVANT-PROPOS Durée Estimée Pour L’ASSEMBLAGE Désemballage ET NettoyageAssemblage Outils Nécessaires Pour L’ASSEMBLAGEPièces DES Barres DE Guidage DU Guide Pièce DU Guide Longitudinal 11,12Pièces DU Volant DE Relèvement DE LA Lame Pièces DU PORTE-GUIDE D’ONGLETPièces DU Socle Fixation DE LA Scie SUR LE Socle PORTE-GUIDE D’ONGLETAssemblage DU Socle Raccord DU SAC À PoussièreRallonges Ensemble DE PROTÈGE-LAME ET Couteau SéparateurUtilisation DES Commandes ET Réglages Réglages DES Butées Positives À 90 ET 45 Degrés Commande D’ABAISSEMENT ET DE Relèvement DE LA LameCommande D’INCLINAISON DE LA Lame Verrouiller L’INTERRUPTEUR EN Position D’ARRÊTRéglage D’UNE Butée Fixe À 45 Degrés Utilisation ET Réglage DU Guide LongitudinalUtilisation ET Réglages DU Guide D’ONGLET Débrancher L’APPAREIL DE LA Source D’ALIMENTATION Opérations Courantes DE SciageChangement DE LA Lame TronçonnageSciage EN Long Fraise Accessoire À RainurerConstruction D’UNE Planche EN Éventail Suivre LES Règles ET Consignes DE Sécurité Guide DE Dépannage« Fabrication DUN Poussoir » Accessoires Conserve Este Manual Para Futuras Consultas Sierra DE Mesa FS210LSDefiniciones DE LAS Normas DE Seguridad Normas Generales DE SeguridadInstrucciones Importantes Sobre Seguridad Normas Generales DE Seguridad Guarde Estas Instrucciones Normas DE Seguridad Adicionales Para LAS Sierras DE MesaConexiones Eléctricas Cables Prolongadores Descripción DE LAS FuncionesIntroducción Tiempo Aproximado Para EL Ensamblaje Desembalaje Y LimpiezaEnsamblaje Herramientas Necesarias Para EL EnsamblajePartes DEL Soporte DE Avance DE Salida Partes DE LA Guía DE Corte LongitudinalPartes DEL Volante Para Elevar LA Hoja Partes DEL Sujetador DEL Calibrador DEPartes DE LA Base Sujetador DEL Calibrador DE IngleteDesconecte LA Máquina DE LA Fuente DE Energía Ensamblado DE LA Hoja Volante Para Elevar Y Bajar Ensamblaje DE LA BaseInserción DE LA Bolsa Recolectora DE Polvo Sierra a LA BaseRiel DE Guía a LA Sierra Bases DE ExtensiónControles DE Operación Y Ajustes Ajustar UN Tope Positivo a 90 Grados Control DE Elevación Y Descenso DE LA HojaControl DE Inclinación DE LA Hoja Ajuste DE Topes Positivos a 90 Y 45 GradosCambio DE LA Hoja Ajustes Y Operación DEL Calibrador DE IngleteEmpujar Operaciones MÁS Comunes DE Corte CON SierraCorte Transversal Corte LongitudinalCabezal Portacuchilla Accesorio Para Ranuras Construcción DE UNA Tabla DE Canto Biselado Guía DE Detección DE ProblemasConstrucción DE UNA Vara Para Empujar Vara DE EmpujeAccesorios