Delta DP300L Operational Controls and Adjustments, Starting and Stopping the Drill Press

Page 14

OPERATION

OPERATIONAL CONTROLS AND ADJUSTMENTS

STARTING AND STOPPING THE DRILL PRESS

1.The on/off switch (A) Fig. 20 is located on the front of the drill press head. To turn the machine "ON", move the switch up to the "ON" position.

2.To turn the machine "OFF", move the switch (A) down to the "OFF" position.

Make sure that the switch is in the "OFF" position before plugging in the power cord. In the event of a power failure, move the switch to the "OFF" position. An accidental start-up can cause injury.

LOCKING SWITCH IN THE "OFF" POSITION

IMPORTANT: When the tool is not in use, the switch should be locked in the "OFF" position to prevent unauthorized use. To lock the machine, grasp the switch toggle (B) Fig. 21 and pull it out of the switch. With the switch toggle (B) removed, the switch will not operate. However, should the switch toggle be removed while the saw is running, the machine can be turned "OFF," but cannot be restarted without re-inserting the switch toggle (B).

A

Fig. 20

FLEXIBLE LAMP

The flexible lamp operates independently of the drill press. To turn the lamp “ON” and “OFF”, rotate switch

(A) Fig. 22.

Fire Hazard. To reduce the risk of fire, use 40 watt or less, 120 volt, reflector track-type light bulb (not supplied). DO NOT use a standard household light bulb. The reflector track-type light bulb should not extend below the lamp shade.

B

Fig. 21

A

Fig. 22

14

Image 14

Contents Bench Drill Press Laser Guides Table of Contents Important Safety InstructionsCalifornia Proposition Safety Guidelines DefinitionsTool Warning Labels General Safety Rules Important Safety InstructionsAdditional Specific Safety Rules Failure to Follow These Rules MAY Result in Serious InjuryAdditional Safety Rules for the Laser EYE Injury Laser LightGrounding Instructions Power ConnectionsMotor Specifications Foreword Functional DescriptionExtension Cords Carton Contents Assembly Time Estimate AssemblyAssembly Tools Required Page Screw front laser housing a to the rear Fastening Drill Press to Supporting Surface Operation Operational Controls and AdjustmentsLocking Switch in the OFF Position Starting and Stopping the Drill PressTable Adjustments Drilling Holes to Depth Changing Speeds and Adjusting Belt TensionSpindle Speeds Spindle MotorMaking Lasers Parallel Adjusting Spindle Return SpringAdjusting Lasers Making Lasers IntersectMachine USE Fig. L4Drilling Wood Installing and Removing Drill BitsCorrect Drilling Speeds Drilling MetalAccessories MaintenanceService WarrantyPrensa para Taladro de Banco de 305 mm Con Guías de Láser Proposición DE California Instrucciones DE Seguridad ImportantesPautas DE SEGURIDAD/DEFINICIONES Guarde Estas InstruccionesNormas Generales DE Seguridad Normas Específicas Adicionales DE Seguridad Lesiones Oculares LUZ Láser Instrucciones DE Conexión a Tierra Conexiones a LA Fuente DE AlimentaciónEspecificaciones DEL Motor Cordones DE Extensión Cordones DE ExtensiónInstrucciones DE Funcionamiento PrefacioContenido DE Carton Desempaquetado Y LimpiezaEstimación DEL Tiempo DE Ensamblaje EnsamblajeHerramientas DE Ensamblaje Requeridas Page Ensamblado DEL Láser Afianzando LA Taladradora DE Banco a LA Superficie DE Apoyo Operación Controles Y Ajustes OperacionalesArbol Motor Velocidades DE ArbolCambio DE Velocidades Y Ajuste DEL Tensionamiento DE Correa Desconecte LA Máquina DE Fuente DE EnergíaPerforacion DE Agujeros a Profundidad Ajuste DEL Resorte DE Retorno DEL ArbolCómo Intersectar LOS Láseres Ajuste DEL LáserCómo Colocar LOS Láseres EN Paralelo Velocidades QUE Perforan Correctas Utilizar LA MaquinaInstalacion Y Extraccion DE Brocas Perforacion DE Maderas Perforacion DE MetalesAccesorios Localizacion DE Fallas MantenimientoServicio Garantia Garantía limitada de dos años para productos nuevosManuel D’UTILISATION LA Proposition DE Californie LES Instructions Importantes DE SureteMesures DE Sécurité Définitions Règles DE Sécurité Générales Lutilisation DE CET OutilRègles Spécifiques Additionnelles DE Sûreté Blessure AUX Yeux Rayonnement Laser Instructions DE Mise À LA Terre Raccordements ÉlectriquesSpécifications DU Moteur AVANT-PROPOS Description FonctionnelleCordon DE Rallonge Contenus DE Boite Désemballage ET NettoyagePage Page Encart compris dans l’emballage du laser Fixation DE LA Perceuse À Colonne À UNE Surface Portante Mise EN Marche ET Arrêt DE LA Perceuse À Colonne FonctionnementLoperation Controle DE LE ET LES Ajustements Verrouillage DE L’INTERRUPTEUR EN Position «OFF» ArrêtRéglages DU Table LA Broche Moteur Vitesses DE LA BrochePerçage À UNE Profondeur Particulière Débranchez LA MachineAlignement Parallèle DES Lasers Réglage DES LasersRéglage DU Ressort DE Retour DE LA Broche Utilisation DE LA Machine Réglage DU Point D’INTERSECTION DES LasersPerçage DU Bois Installation ET Enlèvement DES ForetsBonnes Vitesses DE Perçage Perçage DES MétauxDepannage Entretien Accessoiries Garantie