Delta DP300L Adjusting Spindle Return Spring, Adjusting Lasers, Making Lasers Parallel

Page 17

ADJUSTING SPINDLE RETURN SPRING

The spindle will automatically return slowly to its upper position when the handle is released. The spindle return spring was properly adjusted at the factory. However, to adjust, if necessary:

Disconnect machine from power source.

1.Loosen the nuts (B) and (E) Fig. 31. Make sure that the spring housing (A) remains engaged with head casting (C).

2.While firmly holding the spring housing (A) Fig. 32, pull out the housing and rotate it (counter-clockwise to increase or clockwise to decrease the spring tension) until the boss (D) is engaged with the next notch on the housing. Turn the nut (E) until it contacts the spring housing (A), then back the nut (E) out 1/4 turn from the spring housing (A). Tighten the nut (B) against the nut (E) to hold the housing in place.

IMPORTANT: The inside nut (E) should not contact spring housing (A) when tightened.

A C

B E

Fig. 31

E

D

B

A

Fig. 32

ADJUSTING LASERS

Disconnect machine from power source.

Laser Light. Do not stare into the beam, aperture, or into a reflection from a

mirror-like surface.

MAKING LASERS PARALLEL

1.Install alignment pin (A) into chuck (B). Make sure that the pointed end (C) of the alignment pin is down, as shown in Fig. L1. The black scribed line on the pin should face towards the left laser.

2.Turn on lasers using switch (D) on the front of the laser housing.

3.With a Phillips head screwdriver, remove the two screws (F) Fig. L2 and cap (G) above the left side of laser housing.

4.Loosen the laser retainer screw (H) Fig. L3.

5.Move the laser lever (I) Fig. L3 so the laser is shining on the alignment pin. Adjust the lever (I) until the laser is parallel with the black line.

NOTE: It may be necessary to move the laser holder (J) Fig. L1 to get the laser to shine on the alignment pin. Once the light is on the pin, adjust the laser with the lever (I).

6.When laser is set, tighten the laser retainer screw (H) Fig. L3. Then, replace the cap (G) Fig L2 and loosely tighten the two screws (F).

7.Repeat for the right side.

MAKING LASERS INTERSECT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B

 

 

 

 

 

J

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. L1

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

I

 

 

 

 

 

 

 

 

 

H

 

 

 

 

 

 

 

 

 

F

 

 

 

G

 

 

 

 

 

 

 

 

 

 

 

Fig. L2

 

Fig. L3

17

Image 17
Contents Bench Drill Press Laser Guides Important Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsTool Warning Labels Important Safety Instructions General Safety RulesFailure to Follow These Rules MAY Result in Serious Injury Additional Specific Safety RulesEYE Injury Laser Light Additional Safety Rules for the LaserGrounding Instructions Power ConnectionsMotor Specifications Foreword Functional DescriptionExtension Cords Carton Contents Assembly Time Estimate AssemblyAssembly Tools Required Page Screw front laser housing a to the rear Fastening Drill Press to Supporting Surface Locking Switch in the OFF Position Operational Controls and AdjustmentsOperation Starting and Stopping the Drill PressTable Adjustments Spindle Speeds Changing Speeds and Adjusting Belt TensionDrilling Holes to Depth Spindle MotorAdjusting Lasers Adjusting Spindle Return SpringMaking Lasers Parallel Making Lasers IntersectFig. L4 Machine USECorrect Drilling Speeds Installing and Removing Drill BitsDrilling Wood Drilling MetalService MaintenanceAccessories WarrantyPrensa para Taladro de Banco de 305 mm Con Guías de Láser Pautas DE SEGURIDAD/DEFINICIONES Instrucciones DE Seguridad ImportantesProposición DE California Guarde Estas InstruccionesNormas Generales DE Seguridad Normas Específicas Adicionales DE Seguridad Lesiones Oculares LUZ Láser Instrucciones DE Conexión a Tierra Conexiones a LA Fuente DE AlimentaciónEspecificaciones DEL Motor Instrucciones DE Funcionamiento Cordones DE ExtensiónCordones DE Extensión PrefacioDesempaquetado Y Limpieza Contenido DE CartonEstimación DEL Tiempo DE Ensamblaje EnsamblajeHerramientas DE Ensamblaje Requeridas Page Ensamblado DEL Láser Afianzando LA Taladradora DE Banco a LA Superficie DE Apoyo Controles Y Ajustes Operacionales OperaciónCambio DE Velocidades Y Ajuste DEL Tensionamiento DE Correa Velocidades DE ArbolArbol Motor Desconecte LA Máquina DE Fuente DE EnergíaAjuste DEL Resorte DE Retorno DEL Arbol Perforacion DE Agujeros a ProfundidadCómo Intersectar LOS Láseres Ajuste DEL LáserCómo Colocar LOS Láseres EN Paralelo Velocidades QUE Perforan Correctas Utilizar LA MaquinaInstalacion Y Extraccion DE Brocas Perforacion DE Metales Perforacion DE MaderasAccesorios Localizacion DE Fallas MantenimientoServicio Garantía limitada de dos años para productos nuevos GarantiaManuel D’UTILISATION LA Proposition DE Californie LES Instructions Importantes DE SureteMesures DE Sécurité Définitions Lutilisation DE CET Outil Règles DE Sécurité GénéralesRègles Spécifiques Additionnelles DE Sûreté Blessure AUX Yeux Rayonnement Laser Instructions DE Mise À LA Terre Raccordements ÉlectriquesSpécifications DU Moteur AVANT-PROPOS Description FonctionnelleCordon DE Rallonge Désemballage ET Nettoyage Contenus DE BoitePage Page Encart compris dans l’emballage du laser Fixation DE LA Perceuse À Colonne À UNE Surface Portante Loperation Controle DE LE ET LES Ajustements FonctionnementMise EN Marche ET Arrêt DE LA Perceuse À Colonne Verrouillage DE L’INTERRUPTEUR EN Position «OFF» ArrêtRéglages DU Table Perçage À UNE Profondeur Particulière Vitesses DE LA BrocheLA Broche Moteur Débranchez LA MachineAlignement Parallèle DES Lasers Réglage DES LasersRéglage DU Ressort DE Retour DE LA Broche Réglage DU Point D’INTERSECTION DES Lasers Utilisation DE LA MachineBonnes Vitesses DE Perçage Installation ET Enlèvement DES ForetsPerçage DU Bois Perçage DES MétauxDepannage Entretien Garantie Accessoiries