DeWalt DWE4011 Mounting Guard Accessories and Attachments, 2 114.3 mm Grinding Wheels Wire Wheels

Page 11

4-1/2" (114.3 mm) Grinding Wheels

Wire Wheels

Type 27 guard

backing flange

Type 27 depressed

Type 27 guard

Type 27 hubbed wheel

Type 27 guard

3" (76.2 mm)

wire cup brush

Type 27 guard

4" (101.6 mm) wire wheel

English

center wheel

threaded clamp nut

Use only the accessories shown on pages 9–10 of this manual. Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate.

Mounting Guard

Accessories and Attachments

It is important to choose the correct guards, backing pads and flanges to use with grinder accessories. See pages 9–10 for information on choosing the correct accessories.

WARNING: Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated accessory speed may burst and cause injury. Threaded accessories must have a 5/8"–11 hub. Every unthreaded accessory must have a 7/8" arbor hole. If it does not, it may have been designed for a circular saw and should not be used.

9

CAUTION: Guards must be used with all grinding wheels, cutting wheels, sanding flap discs, wire brushes, and wire wheels. The tool may be used without a guard only when sanding with conventional sanding discs. A Type 27 guard (intended for use with depressed center grinding wheels [Type 27 and Type 29], sanding flap discs, wire wheels and wire cup brushes) is available at extra cost from your local dealer or authorized service center. Grinding and cutting with wheels other than Type 27 and 29 require different accessory guards not included with tool. A Type 1 guard is provided for use with the Type 1 wheel. Mounting instructions for accessory guards are shown below and are also included in the accessory package.

Image 11

Contents Guide D’UTILISATION Manual DE Instrucciones Page Electrical Safety Deﬁnitions Safety GuidelinesGeneral Power Tool Safety Warnings Work Area SafetyService Personal SafetyPower Tool USE and Care Safety Instructions for ALL Operations Causes and Operator Prevention of Kickback Safety Warnings Speciﬁc for Sanding Operations Additional Safety Rules for Grinders Safety Warnings Speciﬁc for Polishing OperationsSafety Warnings Speciﬁc for Wire Brushing Operations Components Fig Save These Instructions for Future USEMotor Intended USE Assembly and AdjustmentsRotating the Gear Case Fig 2 114.3 mm Grinding Wheels Wire Wheels Mounting Guard Accessories and AttachmentsMounting and Removing Type 27 ONE-TOUCHGUARD Guards and Flanges SwitchesOperation Wheels Spindle Lock FIGMounting and Removing Hubbed Wheels Mounting NON-HUBBED Wheels FIGMounting Sanding Backing Pads FIG Surface Grinding with Grinding Wheels FIGEdge Grinding with Grinding Wheels FIG Surface Finishing with Sanding Flap Discs FIGMounting Wire CUP Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsUsing Sanding Backing Pads FIG Mounting Closed Type 1 Guard Mounting and Using Cutting Type 1 WheelsUsing Wire CUP Brushes and Wire Wheels Mounting Cutting Wheels MaintenanceCleaning Using Cutting Wheels FIGDAY Money Back Guarantee Accessories RepairsThree Year Limited Warranty Year Free ServiceSécurité EN Matière D’ÉLECTRICITÉ Déﬁnitions lignes directrices en Matière de sécuritéSécurité DU Lieu DE Travail Sécurité Personnelle Réparation Consignes DE Sécurité Pour Toutes LES OpérationsUtilisation ET Entretien D’UN Outil Électrique Français Causes de l’effet de rebond et prévention par l’opérateur Français Règles additionnelles de sécurité propres aux meuleuses Calibres minimaux des rallonges Volts Description Fig Conserver CES Consignes Pour Utilisation UltérieureMoteur Usage Prévu Assemblage ET RéglagesRotation du carter d’engrenage Fig Fixation DE LA Poignée Latérale FIGInstalación del protector Accessoires et raccordsPonçage Dispositifs de protection et brides FonctionnementMontage ET Démontage DE Meules À Moyeu InterrupteursInterrupteur À Glissière FIG Meulage DE Finition Avec DES Meules FIG Montage DE Meules Sans Moyeu FIGMontage DES Patins D’APPUI ET DE Ponçage FIG Meulage DE Bordure Avec DES Meules FIGUtilisation DES Patins DE Ponçage ET D’APPUI FIG Montage et utilisation de meules de coupe type Montage DE Meules DE Coupe Montage D’UN Dispositif DE Protection Fermé Type 1Utilisation DES Meules DE Coupe FIG AccessoiresNettoyage RéparationsGarantie DE Remboursement DE 90 Jours Garantie limitée de trois ansContrat D’ENTRETIEN Gratuit D’UN AN Seguridad Eléctrica Deﬁniciones Normas de seguridadSeguridad EN EL Área DE Trabajo USO Y Mantenimiento DE LA Herramienta Eléctrica Seguridad PersonalMantenimiento Instrucciones DE Seguridad Para Todas LAS OperacionesEspañol Causas del retroceso y su prevención por parte del operador Español Normas de seguridad adicionales para esmeriladoras Calibre mínimo para juegos de cables Capacidad Voltios Guarde Estas Instrucciones Para Futuras Consultas Componentes FigUSO Debido Ensamblado Y AjustesRotación de la caja de engranajes Fig Accesorios y dispositivosTipo 27 Montaje Y Extracción DEL Protector ONE-TOUCHDe liberación del protector Interruptor Deslizador FIG FuncionamientoProtectores y bridas InterruptoresDiscos DE 1/4 Ensamblado DE Discos SIN Cubo FIGBloqueo DEL EJE FIG Montaje Y Remoción DE Discos CON CuboEsmerilado DE Bordes CON Discos Para Esmerilar FIG Esmerilado DE Superficies CON Discos Para Esmerilar FIGUSO DE Almohadillas DE Respaldo Para Lijar FIG Acabado DE Superficies CON Discos Para Lijar FIGMontaje DE LAS Almohadillas DE Respaldo Para Lijar FIG Montaje y uso de cepillos de alambre y discos de alambre Montaje DEL Protector Cerrado Tipo 1 Montaje y uso de los discos de corte TipoMontaje DE LOS Discos DE Corte MantenimientoLimpieza AccesoriosPara Otras Localidades ReparacionesPóliza de Garantía Garantía DE Reembolso DE SU Dinero POR 90 Días Garantía limitada por tres añosExcepciones AÑO DE Servicio GratuitoDWE4011 Especificaciones