DeWalt DWE4011 instruction manual Safety Warnings Specific for Sanding Operations

Page 7

Safety Warnings Specific for Grinding and Abrasive Cutting-Off Operations

a)Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe.

b)The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator. The guard helps to protect operator from broken wheel fragments and accidental contact with wheel.

c)Wheels must be used only for recommended applications. For example: do not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter.

d)Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.

e)Do not use worn down wheels from larger power tools. Wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst.

Additional Safety Warnings Specific for Abrasive Cutting-Off Operations

a)Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.

b)Do not position your body in line with and behind the rotating wheel. When the wheel, at the point of operation, is moving away from your body, the possible kickback may propel the spinning wheel and the power tool directly at you.

c)When wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may occur. Investigate and take corrective action to eliminate the cause of wheel binding.

d)Do not restart the cutting operation in the workpiece. Let the wheel reach full speed and carefully reenter the cut. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece.

e)Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel.

f)Use extra caution when making a "pocket cut" into existing walls or other blind areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.

Safety Warnings Specific for Sanding Operations

a)Do not use excessively oversized sanding disc paper. Follow manufacturers recommendations, when selecting sanding paper. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback.

English

5

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Guide D’UTILISATION Manual DE Instrucciones Page Electrical Safety Definitions Safety GuidelinesGeneral Power Tool Safety Warnings Work Area Safety Power Tool USE and Care Personal Safety Service Safety Instructions for ALL Operations Causes and Operator Prevention of Kickback Safety Warnings Specific for Sanding Operations Safety Warnings Specific for Wire Brushing Operations Safety Warnings Specific for Polishing OperationsAdditional Safety Rules for Grinders Motor Save These Instructions for Future USEComponents Fig Rotating the Gear Case Fig Assembly and AdjustmentsIntended USE 2 114.3 mm Grinding Wheels Wire Wheels Mounting Guard Accessories and AttachmentsMounting and Removing Type 27 ONE-TOUCHGUARD Operation SwitchesGuards and Flanges Wheels Spindle Lock FIGMounting and Removing Hubbed Wheels Mounting NON-HUBBED Wheels FIGMounting Sanding Backing Pads FIG Surface Grinding with Grinding Wheels FIGEdge Grinding with Grinding Wheels FIG Surface Finishing with Sanding Flap Discs FIGUsing Sanding Backing Pads FIG Mounting and Using Wire Brushes and Wire WheelsMounting Wire CUP Brushes and Wire Wheels Using Wire CUP Brushes and Wire Wheels Mounting and Using Cutting Type 1 WheelsMounting Closed Type 1 Guard Mounting Cutting Wheels MaintenanceCleaning Using Cutting Wheels FIGDAY Money Back Guarantee Accessories RepairsThree Year Limited Warranty Year Free ServiceSécurité DU Lieu DE Travail Définitions lignes directrices en Matière de sécuritéSécurité EN Matière D’ÉLECTRICITÉ Sécurité Personnelle Utilisation ET Entretien D’UN Outil Électrique Consignes DE Sécurité Pour Toutes LES OpérationsRéparation Français Causes de l’effet de rebond et prévention par l’opérateur Français Règles additionnelles de sécurité propres aux meuleuses Calibres minimaux des rallonges Volts Moteur Conserver CES Consignes Pour Utilisation UltérieureDescription Fig Usage Prévu Assemblage ET RéglagesRotation du carter d’engrenage Fig Fixation DE LA Poignée Latérale FIGInstalación del protector Accessoires et raccordsPonçage Dispositifs de protection et brides FonctionnementInterrupteur À Glissière FIG InterrupteursMontage ET Démontage DE Meules À Moyeu Meulage DE Finition Avec DES Meules FIG Montage DE Meules Sans Moyeu FIGMontage DES Patins D’APPUI ET DE Ponçage FIG Meulage DE Bordure Avec DES Meules FIGUtilisation DES Patins DE Ponçage ET D’APPUI FIG Montage et utilisation de meules de coupe type Montage DE Meules DE Coupe Montage D’UN Dispositif DE Protection Fermé Type 1Utilisation DES Meules DE Coupe FIG AccessoiresNettoyage RéparationsContrat D’ENTRETIEN Gratuit D’UN AN Garantie limitée de trois ansGarantie DE Remboursement DE 90 Jours Seguridad EN EL Área DE Trabajo Definiciones Normas de seguridadSeguridad Eléctrica USO Y Mantenimiento DE LA Herramienta Eléctrica Seguridad PersonalMantenimiento Instrucciones DE Seguridad Para Todas LAS OperacionesEspañol Causas del retroceso y su prevención por parte del operador Español Normas de seguridad adicionales para esmeriladoras Calibre mínimo para juegos de cables Capacidad Voltios Guarde Estas Instrucciones Para Futuras Consultas Componentes FigUSO Debido Ensamblado Y AjustesRotación de la caja de engranajes Fig Accesorios y dispositivosTipo 27 Montaje Y Extracción DEL Protector ONE-TOUCHDe liberación del protector Interruptor Deslizador FIG FuncionamientoProtectores y bridas InterruptoresDiscos DE 1/4 Ensamblado DE Discos SIN Cubo FIGBloqueo DEL EJE FIG Montaje Y Remoción DE Discos CON CuboEsmerilado DE Bordes CON Discos Para Esmerilar FIG Esmerilado DE Superficies CON Discos Para Esmerilar FIGMontaje DE LAS Almohadillas DE Respaldo Para Lijar FIG Acabado DE Superficies CON Discos Para Lijar FIGUSO DE Almohadillas DE Respaldo Para Lijar FIG Montaje y uso de cepillos de alambre y discos de alambre Montaje DEL Protector Cerrado Tipo 1 Montaje y uso de los discos de corte TipoMontaje DE LOS Discos DE Corte MantenimientoLimpieza AccesoriosPóliza de Garantía ReparacionesPara Otras Localidades Garantía DE Reembolso DE SU Dinero POR 90 Días Garantía limitada por tres añosExcepciones AÑO DE Servicio GratuitoDWE4011 Especificaciones
Top Page Image Contents