DeWalt DWE4011 Assembly and Adjustments, Rotating the Gear Case Fig, Intended USE

Page 10

English

FIG. 1

A

C

G

H

D

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An

	accidental start-up can cause injury.	FIG. 2
	ATTACHING SIDE HANDLE (FIG. 2)	FIG. 2	C
			C

The side handle (C) can be fitted to either side of the gear case in the threaded holes, as shown. Before using the tool, check that the handle is tightened securely. Use a wrench to firmly tighten the side handle.

	B		F
							E



A. Spindle lock button				E. Threaded clamp nut
B. Spindle				F. Guard
C. Side handle				G. Slider switch
D. Backing flange				H. Guard release lever

INTENDED USE

This grinder is designed for professional grinder, sander, wire brush, polisher or cut-off applications.

DO NOT use under wet conditions or in presence of flammable liquids or gases.

This grinder is a professional power tool. DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool.

8

Rotating the Gear Case (Fig. 3)

1.Removethefourcornerscrewsattaching FIG. 3 the gear case to motor housing.

	2. Without separating the gear case from
	motor housing, rotate the gear case
	head to desired position.
	NOTE: If the gear case and motor housing	90˚	90˚
	become separated by more than 1/8"	90˚	90˚
	become separated by more than 1/8"

(3.17 mm), the tool must be serviced and re-assembled by a DEWALT service center. Failure to have the tool serviced may cause brush, motor and bearing failure.

3.Reinstall screws to attach the gear case to the motor housing. Tighten screws to 18 in.-lbs. torque. Overtightening could cause screws to strip.

Image 10

Contents Guide D’UTILISATION Manual DE Instrucciones Page Work Area Safety Deﬁnitions Safety GuidelinesGeneral Power Tool Safety Warnings Electrical SafetyPower Tool USE and Care Personal SafetyService Safety Instructions for ALL Operations Causes and Operator Prevention of Kickback Safety Warnings Speciﬁc for Sanding Operations Safety Warnings Speciﬁc for Wire Brushing Operations Safety Warnings Speciﬁc for Polishing OperationsAdditional Safety Rules for Grinders Motor Save These Instructions for Future USEComponents Fig Rotating the Gear Case Fig Assembly and AdjustmentsIntended USE Mounting Guard Accessories and Attachments 2 114.3 mm Grinding Wheels Wire WheelsMounting and Removing Type 27 ONE-TOUCHGUARD Operation SwitchesGuards and Flanges Mounting NON-HUBBED Wheels FIG Spindle Lock FIGMounting and Removing Hubbed Wheels WheelsSurface Finishing with Sanding Flap Discs FIG Surface Grinding with Grinding Wheels FIGEdge Grinding with Grinding Wheels FIG Mounting Sanding Backing Pads FIGUsing Sanding Backing Pads FIG Mounting and Using Wire Brushes and Wire WheelsMounting Wire CUP Brushes and Wire Wheels Using Wire CUP Brushes and Wire Wheels Mounting and Using Cutting Type 1 WheelsMounting Closed Type 1 Guard Using Cutting Wheels FIG MaintenanceCleaning Mounting Cutting WheelsYear Free Service Accessories RepairsThree Year Limited Warranty DAY Money Back GuaranteeSécurité DU Lieu DE Travail Déﬁnitions lignes directrices en Matière de sécuritéSécurité EN Matière D’ÉLECTRICITÉ Sécurité Personnelle Utilisation ET Entretien D’UN Outil Électrique Consignes DE Sécurité Pour Toutes LES OpérationsRéparation Français Causes de l’effet de rebond et prévention par l’opérateur Français Règles additionnelles de sécurité propres aux meuleuses Calibres minimaux des rallonges Volts Moteur Conserver CES Consignes Pour Utilisation UltérieureDescription Fig Fixation DE LA Poignée Latérale FIG Assemblage ET RéglagesRotation du carter d’engrenage Fig Usage PrévuAccessoires et raccords Instalación del protectorPonçage Fonctionnement Dispositifs de protection et bridesInterrupteur À Glissière FIG InterrupteursMontage ET Démontage DE Meules À Moyeu Montage DE Meules Sans Moyeu FIG Meulage DE Finition Avec DES Meules FIGMeulage DE Bordure Avec DES Meules FIG Montage DES Patins D’APPUI ET DE Ponçage FIGUtilisation DES Patins DE Ponçage ET D’APPUI FIG Montage et utilisation de meules de coupe type Montage D’UN Dispositif DE Protection Fermé Type 1 Montage DE Meules DE CoupeRéparations AccessoiresNettoyage Utilisation DES Meules DE Coupe FIGContrat D’ENTRETIEN Gratuit D’UN AN Garantie limitée de trois ansGarantie DE Remboursement DE 90 Jours Seguridad EN EL Área DE Trabajo Deﬁniciones Normas de seguridadSeguridad Eléctrica Seguridad Personal USO Y Mantenimiento DE LA Herramienta EléctricaInstrucciones DE Seguridad Para Todas LAS Operaciones MantenimientoEspañol Causas del retroceso y su prevención por parte del operador Español Normas de seguridad adicionales para esmeriladoras Calibre mínimo para juegos de cables Capacidad Voltios Componentes Fig Guarde Estas Instrucciones Para Futuras ConsultasAccesorios y dispositivos Ensamblado Y AjustesRotación de la caja de engranajes Fig USO DebidoMontaje Y Extracción DEL Protector ONE-TOUCH Tipo 27De liberación del protector Interruptores FuncionamientoProtectores y bridas Interruptor Deslizador FIGMontaje Y Remoción DE Discos CON Cubo Ensamblado DE Discos SIN Cubo FIGBloqueo DEL EJE FIG Discos DE 1/4Esmerilado DE Superficies CON Discos Para Esmerilar FIG Esmerilado DE Bordes CON Discos Para Esmerilar FIGMontaje DE LAS Almohadillas DE Respaldo Para Lijar FIG Acabado DE Superficies CON Discos Para Lijar FIGUSO DE Almohadillas DE Respaldo Para Lijar FIG Montaje y uso de cepillos de alambre y discos de alambre Montaje y uso de los discos de corte Tipo Montaje DEL Protector Cerrado Tipo 1Accesorios MantenimientoLimpieza Montaje DE LOS Discos DE CortePóliza de Garantía ReparacionesPara Otras Localidades AÑO DE Servicio Gratuito Garantía limitada por tres añosExcepciones Garantía DE Reembolso DE SU Dinero POR 90 DíasEspecificaciones DWE4011