DeWalt DWE4011 Mounting and Using Cutting Type 1 Wheels, Using Wire CUP Brushes and Wire Wheels

Page 17

NOTICE: Failure to properly seat the wheel hub before turning the tool on may result in damage to tool or wheel.

USING WIRE CUP BRUSHES AND WIRE WHEELS (FIG 14, 15)

Wire wheels and brushes can be used forremoving rust, scale and paint, and for smoothing irregular surfaces.

1.

Allow the tool to reach full speed before

FIG. 14

 

touching the tool to the work surface.

 

2.

Apply minimum pressure to work surface,

 

 

allowing the tool to operate at high

5˚–10˚

 

speed. Material removal rate is greatest

WARNING: A closed, 2-sided cutting wheel guard is not included with this tool but is required when using cutting wheels. Failure to use proper flange and guard can result in injury resulting from wheel breakage and wheel contact. See page 9 for more information.

MOUNTING CLOSED (TYPE 1) GUARD (FIG. 16 –18)

WARNING: If present, the ONE TOUCH™ guard screw, lever and spring must be removed before attempting to mount the closed (Type 1) guard. The removed parts must be retained and reinstalled to use the ONE TOUCH™ guard. Noting the position of these parts before disassembly will aid in reassembly.

English

when the tool operates at high speed.

3.Maintain a 5˚ to 10˚ angle between the tool and work surface for wire cup brushes.

4.Maintain contact between the edge of the wheel and the work surface with wire wheels.

5. Continuously move the tool in a forward and FIG. 15

back motion to avoid creating gouges in the work surface. Allowing the tool to rest on the work surface without moving, or moving the

tool in a circular motion causes burning and swirling marks on the work surface.

1.Open the guard latch (N). Align the lugs (I) on the guard with the slots

(J) on the gear case.

2.Push the guard down until the guard lug engages and rotates freely in the groove on the gear case hub.

3.Rotate guard (F) into desired working position. The guard body should be positioned between the spindle and the operator to provide maximum operator protection.

FIG. 16

J

K

N

6.Remove the tool from the work surface before turning the tool off. Allow the tool to stop rotating before setting it down.

CAUTION: Use extra care when working over an edge, as a sudden sharp movement of grinder may be experienced.

Mounting and Using Cutting

(Type 1) Wheels

Cutting wheels include diamond wheels and abrasive discs. Abrasive cutting wheels for metal and concrete use are available. Diamond blades for concrete cutting can also be used.

15

4.Close the guard latch to secure the FIG. 17 guard on the gear case cover. You

should be unable to rotate the guard by

 

hand when the latch is in closed

 

position. If rotation is possible, tighten

 

the adjusting screw (O) with clamp lever

F

in the closed position. Do not operate

grinder with a loose guard or clamp

 

lever in open position.

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Guide D’UTILISATION Manual DE Instrucciones Page General Power Tool Safety Warnings Definitions Safety GuidelinesWork Area Safety Electrical SafetyService Personal SafetyPower Tool USE and Care Safety Instructions for ALL Operations Causes and Operator Prevention of Kickback Safety Warnings Specific for Sanding Operations Additional Safety Rules for Grinders Safety Warnings Specific for Polishing OperationsSafety Warnings Specific for Wire Brushing Operations Components Fig Save These Instructions for Future USEMotor Intended USE Assembly and AdjustmentsRotating the Gear Case Fig 2 114.3 mm Grinding Wheels Wire Wheels Mounting Guard Accessories and AttachmentsMounting and Removing Type 27 ONE-TOUCHGUARD Guards and Flanges SwitchesOperation Mounting and Removing Hubbed Wheels Spindle Lock FIGMounting NON-HUBBED Wheels FIG WheelsEdge Grinding with Grinding Wheels FIG Surface Grinding with Grinding Wheels FIGSurface Finishing with Sanding Flap Discs FIG Mounting Sanding Backing Pads FIGMounting Wire CUP Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsUsing Sanding Backing Pads FIG Mounting Closed Type 1 Guard Mounting and Using Cutting Type 1 WheelsUsing Wire CUP Brushes and Wire Wheels Cleaning MaintenanceUsing Cutting Wheels FIG Mounting Cutting WheelsThree Year Limited Warranty Accessories RepairsYear Free Service DAY Money Back GuaranteeSécurité EN Matière D’ÉLECTRICITÉ Définitions lignes directrices en Matière de sécuritéSécurité DU Lieu DE Travail Sécurité Personnelle Réparation Consignes DE Sécurité Pour Toutes LES OpérationsUtilisation ET Entretien D’UN Outil Électrique Français Causes de l’effet de rebond et prévention par l’opérateur Français Règles additionnelles de sécurité propres aux meuleuses Calibres minimaux des rallonges Volts Description Fig Conserver CES Consignes Pour Utilisation UltérieureMoteur Rotation du carter d’engrenage Fig Assemblage ET RéglagesFixation DE LA Poignée Latérale FIG Usage PrévuInstalación del protector Accessoires et raccordsPonçage Dispositifs de protection et brides FonctionnementMontage ET Démontage DE Meules À Moyeu InterrupteursInterrupteur À Glissière FIG Meulage DE Finition Avec DES Meules FIG Montage DE Meules Sans Moyeu FIGMontage DES Patins D’APPUI ET DE Ponçage FIG Meulage DE Bordure Avec DES Meules FIGUtilisation DES Patins DE Ponçage ET D’APPUI FIG Montage et utilisation de meules de coupe type Montage DE Meules DE Coupe Montage D’UN Dispositif DE Protection Fermé Type 1Nettoyage AccessoiresRéparations Utilisation DES Meules DE Coupe FIGGarantie DE Remboursement DE 90 Jours Garantie limitée de trois ansContrat D’ENTRETIEN Gratuit D’UN AN Seguridad Eléctrica Definiciones Normas de seguridadSeguridad EN EL Área DE Trabajo USO Y Mantenimiento DE LA Herramienta Eléctrica Seguridad PersonalMantenimiento Instrucciones DE Seguridad Para Todas LAS OperacionesEspañol Causas del retroceso y su prevención por parte del operador Español Normas de seguridad adicionales para esmeriladoras Calibre mínimo para juegos de cables Capacidad Voltios Guarde Estas Instrucciones Para Futuras Consultas Componentes FigRotación de la caja de engranajes Fig Ensamblado Y AjustesAccesorios y dispositivos USO DebidoTipo 27 Montaje Y Extracción DEL Protector ONE-TOUCHDe liberación del protector Protectores y bridas FuncionamientoInterruptores Interruptor Deslizador FIGBloqueo DEL EJE FIG Ensamblado DE Discos SIN Cubo FIGMontaje Y Remoción DE Discos CON Cubo Discos DE 1/4Esmerilado DE Bordes CON Discos Para Esmerilar FIG Esmerilado DE Superficies CON Discos Para Esmerilar FIGUSO DE Almohadillas DE Respaldo Para Lijar FIG Acabado DE Superficies CON Discos Para Lijar FIGMontaje DE LAS Almohadillas DE Respaldo Para Lijar FIG Montaje y uso de cepillos de alambre y discos de alambre Montaje DEL Protector Cerrado Tipo 1 Montaje y uso de los discos de corte TipoLimpieza MantenimientoAccesorios Montaje DE LOS Discos DE CortePara Otras Localidades ReparacionesPóliza de Garantía Excepciones Garantía limitada por tres añosAÑO DE Servicio Gratuito Garantía DE Reembolso DE SU Dinero POR 90 DíasDWE4011 Especificaciones
Top Page Image Contents