DeWalt DWE4011 Mounting and Using Wire Brushes and Wire Wheels, Using Sanding Backing Pads FIG

Page 16

English

1.Place or appropriately thread backing pad (L) on the spindle.

2.Place the sanding disc (M) on the backing pad.

3.While depressing spindle lock, thread the clamp nut (E) on spindle, piloting the raised hub on the clamp nut into the center of sanding disc and backing pad.

4.Tighten the clamp nut by hand. Then depress the spindle lock button while turning the sanding disc until the sanding disc and clamp nut are snug.

FIG. 12

M

E

L

2.

Apply minimum pressure to work FIG. 13

 

 

surface, allowing the tool to operate at

 

 

high speed. Sanding rate is greatest

 

 

when the tool operates at high speed.

 

3.

Maintain a 5˚ to 15˚ angle between the

5˚–15˚

 

tool and work surface. The sanding

 

 

 

disc should contact approximately

 

 

one inch of work surface.

 

4. Move the tool constantly in a straight line to prevent burning and

swirling of work surface. Allowing the tool to rest on the work

surface without moving, or moving the tool in a circular motion

causes burning and swirling marks on the work surface.

5. Remove the tool from work surface before turning tool off. Allow

the tool to stop rotating before laying it down.

5.To remove the wheel, grasp and turn the backing pad and sanding pad while depressing the spindle lock button.

USING SANDING BACKING PADS (FIG. 13)

Choose the proper grit sandpaper for your application. Sandpaper is available in various grits. Coarse grits yield faster material removal rates and a rougher finish. Finer grits yield slower material removal and a smoother finish.

Begin with coarse grit discs for fast, rough material removal. Move to a medium grit paper and finish with a fine grit disc for optimal finish.

Coarse

16 – 30 grit

Medium

36 – 80 grit

Fine Finishing

100 – 120 grit

Very Fine Finishing

150 – 180 grit

1.Allow the tool to reach full speed before touching tool to the work surface.

14

Mounting and Using Wire Brushes and Wire Wheels

Wire cup brushes or wire wheels screw directly on the grinder spindle without the use of flanges. Use only wire brushes or wheels provided with a 5/8"–11 threaded hub. A Type 27 guard is required when using wire brushes and wheels.

CAUTION: Wear work gloves when handling wire brushes and wheels. They can become sharp.

CAUTION: Wheel or brush must not touch guard when mounted or while in use. Undetectable damage could occur to the accessory, causing wires to fragment from accessory wheel or cup.

MOUNTING WIRE CUP BRUSHES AND WIRE WHEELS

1.Thread the wheel on the spindle by hand.

2.Depress spindle lock button and use a wrench on the hub of the wire wheel or brush to tighten the wheel.

3.To remove the wheel, reverse the above procedure.

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Guide D’UTILISATION Manual DE Instrucciones Page Definitions Safety Guidelines General Power Tool Safety WarningsWork Area Safety Electrical SafetyPower Tool USE and Care Personal SafetyService Safety Instructions for ALL Operations Causes and Operator Prevention of Kickback Safety Warnings Specific for Sanding Operations Safety Warnings Specific for Wire Brushing Operations Safety Warnings Specific for Polishing OperationsAdditional Safety Rules for Grinders Motor Save These Instructions for Future USEComponents Fig Rotating the Gear Case Fig Assembly and AdjustmentsIntended USE Mounting Guard Accessories and Attachments 2 114.3 mm Grinding Wheels Wire WheelsMounting and Removing Type 27 ONE-TOUCHGUARD Operation SwitchesGuards and Flanges Spindle Lock FIG Mounting and Removing Hubbed WheelsMounting NON-HUBBED Wheels FIG WheelsSurface Grinding with Grinding Wheels FIG Edge Grinding with Grinding Wheels FIGSurface Finishing with Sanding Flap Discs FIG Mounting Sanding Backing Pads FIGUsing Sanding Backing Pads FIG Mounting and Using Wire Brushes and Wire WheelsMounting Wire CUP Brushes and Wire Wheels Using Wire CUP Brushes and Wire Wheels Mounting and Using Cutting Type 1 WheelsMounting Closed Type 1 Guard Maintenance CleaningUsing Cutting Wheels FIG Mounting Cutting WheelsAccessories Repairs Three Year Limited WarrantyYear Free Service DAY Money Back GuaranteeSécurité DU Lieu DE Travail Définitions lignes directrices en Matière de sécuritéSécurité EN Matière D’ÉLECTRICITÉ Sécurité Personnelle Utilisation ET Entretien D’UN Outil Électrique Consignes DE Sécurité Pour Toutes LES OpérationsRéparation Français Causes de l’effet de rebond et prévention par l’opérateur Français Règles additionnelles de sécurité propres aux meuleuses Calibres minimaux des rallonges Volts Moteur Conserver CES Consignes Pour Utilisation UltérieureDescription Fig Assemblage ET Réglages Rotation du carter d’engrenage FigFixation DE LA Poignée Latérale FIG Usage PrévuAccessoires et raccords Instalación del protectorPonçage Fonctionnement Dispositifs de protection et bridesInterrupteur À Glissière FIG InterrupteursMontage ET Démontage DE Meules À Moyeu Montage DE Meules Sans Moyeu FIG Meulage DE Finition Avec DES Meules FIGMeulage DE Bordure Avec DES Meules FIG Montage DES Patins D’APPUI ET DE Ponçage FIGUtilisation DES Patins DE Ponçage ET D’APPUI FIG Montage et utilisation de meules de coupe type Montage D’UN Dispositif DE Protection Fermé Type 1 Montage DE Meules DE CoupeAccessoires NettoyageRéparations Utilisation DES Meules DE Coupe FIGContrat D’ENTRETIEN Gratuit D’UN AN Garantie limitée de trois ansGarantie DE Remboursement DE 90 Jours Seguridad EN EL Área DE Trabajo Definiciones Normas de seguridadSeguridad Eléctrica Seguridad Personal USO Y Mantenimiento DE LA Herramienta EléctricaInstrucciones DE Seguridad Para Todas LAS Operaciones MantenimientoEspañol Causas del retroceso y su prevención por parte del operador Español Normas de seguridad adicionales para esmeriladoras Calibre mínimo para juegos de cables Capacidad Voltios Componentes Fig Guarde Estas Instrucciones Para Futuras ConsultasEnsamblado Y Ajustes Rotación de la caja de engranajes FigAccesorios y dispositivos USO DebidoMontaje Y Extracción DEL Protector ONE-TOUCH Tipo 27De liberación del protector Funcionamiento Protectores y bridasInterruptores Interruptor Deslizador FIGEnsamblado DE Discos SIN Cubo FIG Bloqueo DEL EJE FIGMontaje Y Remoción DE Discos CON Cubo Discos DE 1/4Esmerilado DE Superficies CON Discos Para Esmerilar FIG Esmerilado DE Bordes CON Discos Para Esmerilar FIGMontaje DE LAS Almohadillas DE Respaldo Para Lijar FIG Acabado DE Superficies CON Discos Para Lijar FIGUSO DE Almohadillas DE Respaldo Para Lijar FIG Montaje y uso de cepillos de alambre y discos de alambre Montaje y uso de los discos de corte Tipo Montaje DEL Protector Cerrado Tipo 1Mantenimiento LimpiezaAccesorios Montaje DE LOS Discos DE CortePóliza de Garantía ReparacionesPara Otras Localidades Garantía limitada por tres años ExcepcionesAÑO DE Servicio Gratuito Garantía DE Reembolso DE SU Dinero POR 90 DíasEspecificaciones DWE4011
Top Page Image Contents