DeWalt DWE4011 instruction manual Operation, Guards and Flanges, Switches

Page 13

5.For easy adjustment, the guard can be rotated in the clockwise direction. NOTE: The guard release lever should snap into one of the alignment holes (K) on the guard collar. This insures that the guard is secure. The guard can be repositioned the opposite direction by depressing the guard release lever.

6.To remove the guard, follow steps 1–3 of these instructions in reverse.

NOTE: Edge grinding and cutting can be performed with Type 27 wheels designed and specified for this purpose; 1/4" (6.35 mm) thick wheels are designed for surface grinding while 1/8" (3.17 mm) wheels are designed for edge grinding. Cutting can also be performed by using a Type 1 wheel and a Type 1 guard.

OPERATION

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury.

Guards and Flanges

It is important to choose the correct guards and flanges to use with the grinder accessories. See page 9–10 and this page for the correct accessories.

NOTE: Edge grinding and cutting can be performed with Type 27 wheels designed and specified for this purpose.

WARNING: Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated accessory speed may burst and cause injury. Every unthreaded accessory must have a 7/8" arbor hole. If it does not, it may have been designed for a circular saw and should not be used. Use only the accessories shown on pages 9–10. Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate.

11

Switches

CAUTION: Hold the side handle and body of the tool firmly to maintain control of the tool at start up and during use and until the wheel or accessory stops rotating. Make sure the wheel has come to a complete stop before laying the tool down.

NOTE: To reduce unexpected tool movement, do not switch the tool on or off while under load conditions. Allow the grinder to run up to full speed before touching the work surface. Lift the tool from the surface before turning the tool off. Allow the tool to stop rotating before putting it down.

SLIDER SWITCH (FIG. 6)

FIG. 6

WARNING: Before connecting the

 

 

 

tool to a power supply, be sure the

 

 

 

slider switch is in the off position by

 

 

 

pressing the rear part of the switch and

 

 

H

releasing. Ensure the slider switch is in

 

 

 

 

 

the off position as described above

 

 

 

 

 

 

after any interruption in power supply

 

 

 

 

 

 

to the tool, such as the activation of a ground fault interrupter, throwing of a circuit breaker, accidental unplugging, or power failure. If the slider switch is locked on when the power is connected, the tool will start unexpectedly.

To start the tool, slide the ON/OFF slider switch (H) toward the front of the tool. To stop the tool, release the ON/OFF slider switch.

For continuous operation, slide the switch toward the front of the tool and press the forward part of the switch inward. To stop the tool while operating in continuous mode, press the rear part of the slider switch and release.

English

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Guide D’UTILISATION Manual DE Instrucciones Page General Power Tool Safety Warnings Definitions Safety GuidelinesWork Area Safety Electrical SafetyPower Tool USE and Care Personal SafetyService Safety Instructions for ALL Operations Causes and Operator Prevention of Kickback Safety Warnings Specific for Sanding Operations Safety Warnings Specific for Wire Brushing Operations Safety Warnings Specific for Polishing OperationsAdditional Safety Rules for Grinders Motor Save These Instructions for Future USEComponents Fig Rotating the Gear Case Fig Assembly and AdjustmentsIntended USE 2 114.3 mm Grinding Wheels Wire Wheels Mounting Guard Accessories and AttachmentsMounting and Removing Type 27 ONE-TOUCHGUARD Operation SwitchesGuards and Flanges Mounting and Removing Hubbed Wheels Spindle Lock FIGMounting NON-HUBBED Wheels FIG WheelsEdge Grinding with Grinding Wheels FIG Surface Grinding with Grinding Wheels FIGSurface Finishing with Sanding Flap Discs FIG Mounting Sanding Backing Pads FIGUsing Sanding Backing Pads FIG Mounting and Using Wire Brushes and Wire WheelsMounting Wire CUP Brushes and Wire Wheels Using Wire CUP Brushes and Wire Wheels Mounting and Using Cutting Type 1 WheelsMounting Closed Type 1 Guard Cleaning MaintenanceUsing Cutting Wheels FIG Mounting Cutting WheelsThree Year Limited Warranty Accessories RepairsYear Free Service DAY Money Back GuaranteeSécurité DU Lieu DE Travail Définitions lignes directrices en Matière de sécuritéSécurité EN Matière D’ÉLECTRICITÉ Sécurité Personnelle Utilisation ET Entretien D’UN Outil Électrique Consignes DE Sécurité Pour Toutes LES OpérationsRéparation Français Causes de l’effet de rebond et prévention par l’opérateur Français Règles additionnelles de sécurité propres aux meuleuses Calibres minimaux des rallonges Volts Moteur Conserver CES Consignes Pour Utilisation UltérieureDescription Fig Rotation du carter d’engrenage Fig Assemblage ET RéglagesFixation DE LA Poignée Latérale FIG Usage PrévuInstalación del protector Accessoires et raccordsPonçage Dispositifs de protection et brides FonctionnementInterrupteur À Glissière FIG InterrupteursMontage ET Démontage DE Meules À Moyeu Meulage DE Finition Avec DES Meules FIG Montage DE Meules Sans Moyeu FIGMontage DES Patins D’APPUI ET DE Ponçage FIG Meulage DE Bordure Avec DES Meules FIGUtilisation DES Patins DE Ponçage ET D’APPUI FIG Montage et utilisation de meules de coupe type Montage DE Meules DE Coupe Montage D’UN Dispositif DE Protection Fermé Type 1Nettoyage AccessoiresRéparations Utilisation DES Meules DE Coupe FIGContrat D’ENTRETIEN Gratuit D’UN AN Garantie limitée de trois ansGarantie DE Remboursement DE 90 Jours Seguridad EN EL Área DE Trabajo Definiciones Normas de seguridadSeguridad Eléctrica USO Y Mantenimiento DE LA Herramienta Eléctrica Seguridad PersonalMantenimiento Instrucciones DE Seguridad Para Todas LAS OperacionesEspañol Causas del retroceso y su prevención por parte del operador Español Normas de seguridad adicionales para esmeriladoras Calibre mínimo para juegos de cables Capacidad Voltios Guarde Estas Instrucciones Para Futuras Consultas Componentes FigRotación de la caja de engranajes Fig Ensamblado Y AjustesAccesorios y dispositivos USO DebidoTipo 27 Montaje Y Extracción DEL Protector ONE-TOUCHDe liberación del protector Protectores y bridas FuncionamientoInterruptores Interruptor Deslizador FIGBloqueo DEL EJE FIG Ensamblado DE Discos SIN Cubo FIGMontaje Y Remoción DE Discos CON Cubo Discos DE 1/4Esmerilado DE Bordes CON Discos Para Esmerilar FIG Esmerilado DE Superficies CON Discos Para Esmerilar FIGMontaje DE LAS Almohadillas DE Respaldo Para Lijar FIG Acabado DE Superficies CON Discos Para Lijar FIGUSO DE Almohadillas DE Respaldo Para Lijar FIG Montaje y uso de cepillos de alambre y discos de alambre Montaje DEL Protector Cerrado Tipo 1 Montaje y uso de los discos de corte TipoLimpieza MantenimientoAccesorios Montaje DE LOS Discos DE CortePóliza de Garantía ReparacionesPara Otras Localidades Excepciones Garantía limitada por tres añosAÑO DE Servicio Gratuito Garantía DE Reembolso DE SU Dinero POR 90 DíasDWE4011 Especificaciones
Top Page Image Contents