Remington 498 Tool Assembly, Attaching Liner to Tool Body, Attaching Firing PIN Assembly

Page 21

Tool Disassembly and

Assembly

TOOL ASSEMBLY

A. ATTACHING LINER TO TOOL BODY

1.Replace two ball bearings and springs into end of liner (see Figure 9, page 20).

2.Slide tool body onto liner.

3.Insert two screws into front of tool body just under liner. Tighten screws ﬁrmly.

B. ATTACHING TRIGGER ASSEMBLY TO TOOL BODY

1.Insert trigger assembly into tool body at rear of body (see Figure 8, page 20).

2.Replace trigger pin. Do this by inserting trigger pin through tool body and trigger assembly. After pin is inserted, tighten pin ﬁrmly using a standard screw driver.

C. ATTACHING FIRING PIN ASSEMBLY

1.Insert push pin into tool body (see item 11, page 17, for push pin location). Hole for push pin is located in cylinder at rear of tool. The hole for the push pin is located beside center hole in cylinder. Insert narrow end of pin ﬁrst.

2.Insert sear assembly into cylinder at rear of tool body. Sear assembly consists of sear, spring, and sear holder (see items 20, 21, & 22, page 17). Insert sear as- sembly sear-end ﬁrst (see Figure 10). Make sure sear is pointing towards bottom of tool. Note: Use screw driver to depress sear so sear assembly can pass into cylinder. Press sear assembly into cylinder until it stops. Note: Sear can be seen through slot in bottom of cylinder. Use screw driver to depress sear through slot. Move sear assembly further into cylinder until sear is located at center of slot.

Sear Assembly

Sear

Sear

Slot

Figure 10 - Inserting Sear Assembly Into Cylinder As

Viewed From Bottom Of Tool

3.Insert ﬁring pin (point-ﬁrst) into sear assembly. Make sure notched side of ﬁring pin is pointing towards top of tool body. Do not force ﬁring pin assembly into place. Use screw driver to depress sear through slot in cylinder. With free hand, gently press ﬁring pin until it drops into place.

4.Place smaller diameter spring into sear assembly. Make sure spring is over top of ﬁring pin (see Figure 7, page 20).

5.Place large diameter spring over top of smaller spring (see Figure 7, page 20).

6.Place plug over end of both springs.

7.Press plug to tool body. This will compress the springs into the tool body. After plug enters tool body, turn plug 90° to lock plug.

114915

21

Image 21

Contents Operating Instructions Index Power Load14-16 18-22Before Using PrecautionsHandling the Tool Safety PrecautionsPowe Know Your Fastening Base Material CenterPunch Test Tile Brick Never make fastenings in spalled or cracked areasAlways hold tool perpendicular to work surface Operating the ToolPower Loads and Power Fasteners Never use power loads in ﬁrearms Failure to start withCondition and will re Sult in damage to tool See Unload Head Shank Plastic FluteWhy a Power Fastener Holds WHY a Power Fastener Holds in ConcreteWHY a Power Fastener Holds in Steel Overdriven Power Fasteners and Piston Power LoadsFastening Into Concrete Fastening Into SteelOperation Water Parts List MaintenancePiston Overdrive Key Part Description 493 498Accessories Tool Disassembly Tool Disassembly AssemblyRemoving Barrel Assembly Push stop towards rear of tool and remove see FigureTilt rear of base plate down. Guide will slide out Remove piston assembly from piston sleeve see FigureRemoving Rubber PAD Removing Rocker ARMRemoving Trigger Assembly Removing Firing PINRemoving Liner from Tool Body Attaching Trigger Assembly to Tool Body Tool AssemblyAttaching Firing PIN Assembly Attaching Liner to Tool BodyAssembling Barrel Assembly Attaching Rubber PADInsert guide into rear of base plate see Figure Problem Possible Cause Remedy Troubleshooting GuidePower load and power fastener application information Application ChartPlete tool see Mainte Age the toolStock Load Color CodeCase NumberTechnical Service Replacement Parts And AccessoriesRepair Service Warranty ServiceFBD Parts CentralsFax Limited WarrantyInstrucciones de operación El Índice RegletadecargasNo se provee con la herramienta Precauciones de Seguridad Antes DE UsarEn seguir las precauciones contenidas en este manual Manipulación DE LA Herramienta Carg Conozca EL Material DE LA Base DE Sujeción Prueba DELPunzón Baldosa Ladrillo Operación DE LA Herramienta Cargas Explosivas Y Sujetadores DE Potencia Nunca use las cargas explosivas en armas de fuego NotaDescarga ¿PORQUÉ UN Sujetador DE Potencia SE Sostiene EN EL ACERO? ¿Porque Un Sujetador De Potencia Sostiene?Sujeción EN Acero Sujeción EN ConcretoCargas Explosivas CorrectoOperación Agua Lista de partes MantenimientoImpulso Excesivo DEL Pistón ImportanteDe parte Descripción AccesoriosDesarmado y armado de la herramienta Desarmado DE LA HerramientaRetiro DEL Conjunto Cañón Retiro DEL Balancín Retiro DE LA Amohadilla DE CauchoRetiro DEL Conjunto Gatillo Retiro DE LA Espiga DE DisparoRetiro DEL Forro DEL Cuerpo DE LA Herramienta Armado DE LA HerramientaAcople EL Forro AL Cuerpo DE LA Herramienta Acople EL Conjunto Gatillo AL Cuerpo DE LA HerramientaAcople DEL Conjunto Espiga DE Disparo Ensamble DEL Conjunto Cañón Acople DE LA Almohadilla DE CauchoGuia de Investigacion de Averias Problema Causa Probable RemedioTabla de utilización Importante Número Código de DelArtículo Servicio Técnico Accesorios y piezas de repuestoServicio de Reparación Servicio CON GarantíaCentros de repuestos Impreso en Taiwan Garantía LimitadaMode ’emploi 60-68 Index71-73 75-79Avant L’UTILISATION Avertissement Mesures de précautionManipulation DE L’OUTIL Cartou Trop MOU Bien Connaître LE Matériau DE BaseCarreaux Brique Utilisation DE L’OUTIL Cartouches Explosives ET Goujons D’ANCRAGE Remarque Décharger Tige TêteAncrage d’un goujon d’ancrage Pourquoi LE Goujon D’ANCRAGE Tient Dans LE BétonPourquoi LE Goujon D’ANCRAGE Tient Dans L’ACIER Ancrage Dans L’ACIER Ancrage Dans LE BétonCartouches Explosives Surcharge DES Goujons ’ANCRAGE ET DU PistonUtilisation Utilisation Liste des pièces EntretienSurcharge DU Piston Clé Pièce Description 493 498Pièce Description AccessoiresDémontage et montage de l’outil Démontage DE L’OUTILDémontage DU Tube Retirer le piston du manchon du piston Figure Retrait DU Tampon DE CaoutchoucRetrait DU Culbuteur Retrait DU Percuteur Retrait DE L’ENSEMBLE DéclencheurRetrait DU Cylindre Extérieur DU Corps DE L’OUTIL Fixation DU Cylindre AU Corps DE L’OUTIL Montage DE L’OUTILFixation DE L’ENSEMBLE Déclencheur AU Corps DE L’OUTIL Fixation DE L’ENSEMBLE PercuteurFixation DE L’ENSEMBLE Tube Fixation DU Tampon DE CaoutchoucInsérer le guide à l’arrière de la plaque de base Insérer le piston dans le manchon du piston FigureGuide de Dépannage Problème Cause Possible SolutionTableau des applications Niveau NuméroDe stock Service Techique Pièces de rechange et accessoiresService de Réparation Service Sous GarantieCentres de pièces Maintenance Log/Diario de mantenimiento/Registre d’entretien Maintenance Log/Diario de mantenimiento/Registre d’entretien Maintenance Log/Diario de mantenimiento/Registre d’entretien Garantie Limitée 114915-01Imprimé à Taïwan 06/06