Husqvarna FS 700 EX manual Stop cutting

Page 14

Operator’s Manual FS 700EX

Start blade rotation by turning the switch towards the lamp that is on. If the switch is turned in the opposite direction the blade will rotate in the wrong direction.

0

11

Feed the saw blade by turning the blade feed lever towards you, so that a cutting depth adapted to the floor material, however at least 20 mm, is realized.

Make a pilot cut at an even speed at this depth along the pre-drawn line. When the complete pilot cut has been made, raise the blade, shut off the water coolant and stop the blade rotating. Reverse the machine to the starting point.

Align the machine with the pilot cut again and start the machine as above.

Lower the saw blade to a suitable cutting depth (5-10 cm). A suitable cutting depth varies depending on the floor material and the speed.

A simple rule is if the machine tends to “climb up” out of the pilot cut the cutting depth is too large and/or the speed too high.

The machine must not be driven faster than that it cuts without “climbing” i.e. that the machine's front wheels lift off from the ground. If the machine “climbs”, decrease the trolley feed by turning the lever for the travel feed anticlockwise or raise the blade by turning the blade feed lever clockwise

NOTE!

The operator must always be behind the machine when cutting and within reach of the levers and stop.

WARNING!

Contact with the rotating saw blade can result in serious, physical injury or even death.

Stop cutting

Lift up the cutting bridge to its highest position.

Shut down blade rotation by turning the switch the neutral position.

Turn both the travel feed and blade feed to their neutral positions.

Shut off the water coolant.

NOTE!

The protective devices are for your own safety, consequently, it is extremely important to check all safety equipment regularly. Should a fault be discovered, please contact your dealer.

14 - English

Image 14
Contents Gebruiksaanwijzing p Operator´s manual p.3Bedienungsanweisung p Istruzioni per l’uso pPage Contents EnglishOperator’s Manual Protective equipment Key to symbolsManual Electrical WarningSafety Instructions Introduction What is what Hose holder Handle settingAdjuster screw Blade guardTechnical data Weight excl. blade 155 kgAssembling/Replacing the blade OperationBefore cutting Connecting the machine Sawing Stop cutting Transport Maintenance Trouble shooting Fault Cause ActionEnglish EU declaration of conformity Operator’s Manual FS 700EX Deutsch InhaltBedienungsanleitung FS 700EX Erklärung der Symbole Sicherheitsvorschriften WarnungEinleitung Was ist was? Spritzschutz SchlauchhalterTrennscheibenschutz TrennscheibenflanschTechnische Daten AchtungEinbau/Austausch der Trennscheibe BedienungVor dem Sägen Maschine anschließen Schneiden Schneiden beenden Transport Wartung Fehlersuche Fehler Ursache MaßnahmeDeutsch Bedienungsanleitung FS 700EX EU-Erklärung Inhoudsopgave InhoudsopgaveInhoudsopgave Verklaring van de symbolen Gebruiksaanwijzing FS 700EX Veiligheidsinstructies WaarschuwingGebruiksaanwijzing FS 700EX Inleiding Gebruiksaanwijzing FS 700EX Wat is wat Schijfbeschermer HandgreepinstellingSlanghouder SpatbeschermingTechnische gegevens Gewicht excl. schijf 155 kg Gewicht incl. schijf 150 kgGebruiksaanwijzing FS 700EX Monteren/Vervangen van schijf GebruikVoor het zagen De machine aansluiten Zagen Zagen beëindigen Transport Onderhoud Opsporen van storingen LET OPBedienungsanleitung FS 700EX EU-verklaring Bedienungsanleitung FS 700EX Contenuto ContenutoContenuto Avvertenza ManualeDispositivi di protezione individuale AttenzioneDisposizioni di sicurezza AvvertenzaIntroduzione Identificazione delle parti Paraspruzzi PortaflessibiliProtezione del disco Flangia del discoDati tecnici Peso escl. disco 155 kg Peso incl. disco 150 kgMontaggio/sostituzione del disco FunzionamentoPrima del taglio Collegamento della macchina Taglio Conclusione del taglio Trasporto Manutenzione Ricerca dei guasti Difetto Causa InterventoItaliano Dichiarazione di conformità CE Istruzioni per l’uso FS 700EX 115 04 2006-12-14