Operator’s Manual FS 700EX
Trouble shooting
NOTE
Before rectifying a fault, check that all electrical connections are disconnected to prevent the machine from starting during the course of the work.
If a fault occurs, first check whether it coincides with any of the possible faults in the trouble shooting guide below.
If the fault coincides with one of the fault possibilities in the trouble shooting guide, contact your dealer for further information.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Fault | Cause | Action | ||||||
|
|
|
|
|
|
| |||
| The blade rotates in the wrong direction. | The starter knob is defective. | Turn the starter knob in the direction | ||||||
|
|
|
|
|
|
|
|
| indicated by the lit lamp. |
|
|
|
|
|
|
| |||
| The blade jams. | Drive belt slips. | Tension the drive belt. | ||||||
|
| Drive belt dirty. | Clean the drive belt. | ||||||
|
| Drive belt worn. | Replace the drive belt. | ||||||
|
|
|
|
|
|
|
| ||
| No water is produced or too little water | The blade flange is | dirty | Clean the blade flange. | |||||
| reaches the blade. |
|
|
|
|
|
|
| Increase the water pressure by opening |
|
|
|
|
|
|
|
|
| the water tap a little more. |
|
|
|
|
|
|
|
| ||
| The blade jams. | The blade is worn. |
|
|
| Replace the blade. | |||
|
| The saw blade is | clamped. | Support the saw block with braces or a | |||||
|
|
|
|
|
|
|
|
| jack. |
|
| The saw has been | fed too hard. | Run with either a lower feed rate or | |||||
|
|
|
|
|
|
|
|
| shallower cutting depth. |
|
|
|
|
|
|
|
| ||
| The motor does not start. | The emergency stop has been switched | Reset the emergency stop. | ||||||
|
| on. | Contact your dealer. | ||||||
|
| Electrical fault. |
| ||||||
|
|
|
|
|
|
| |||
| There is no trolley feed. | The drive shaft is not engaged. | Change the foot lever for propulsion so | ||||||
|
|
|
|
|
|
|
|
| that the drive shaft is engaged. |
|
|
|
|
|
|
| |||
| There is no trolley feed/blade feed. | The feed levers were not reset when the | Reset the machine by turning off the | ||||||
|
| power was connected. | blade rotation, pressing down the | ||||||
|
|
|
|
|
|
|
|
| emergency stop and turning the levers to |
|
|
|
|
|
|
|
|
| the neutral position. Wait 3 seconds and |
|
|
|
|
|
|
|
|
| then reset the emergency stop button. |
|
|
|
|
|
|
| |||
| There is no blade feed up or down. | The feeder nut has jammed at the end | Remove the rear cover and carefully | ||||||
|
| position. | loosen the feed nut by turning the nut at | ||||||
|
|
|
|
|
|
|
|
| the bottom of the feed screw. |
|
|
|
|
|
|
|
|
| Grease the feed axle. |
|
| The feed nut is dry. |
| ||||||
|
|
|
|
|
|
|
|
| |
| The machine cuts out / does not start | The thermal | Wait until the motor has cooled. Once the | ||||||
| blade rotation. | tripped. | temperature of the motor has dropped | ||||||
|
|
|
|
|
|
|
|
| the saw is started again as normal. |
|
|
|
|
|
|
| |||
| Both status lamps for blade rotation are | A phase is down. | Check the fuses and electrical power | ||||||
| on. |
|
|
|
|
|
|
| cable. |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
English - 17