Nilfisk-Advance America 5200B Skirt Height and Operation Check, Battery Charging, Side skirt

Page 16

INSTRUCTIONS FOR USE

14.Reassemble all the components of the filter in the reverse order of disassembly.

15.If necessary, clean the filter compartment rubber seal (3, Fig. AB) along its perimeter and check its integrity. If necessary, replace it.

16.Reassemble all the components in the reverse order of disassembly.

SKIRT HEIGHT AND OPERATION CHECK

Side skirt

1.Drive the machine on a level ground that is suitable for checking the skirt height.

2.Engage the parking brake by means of the pedal and the lever (26 and 19, Fig. B).

3.Turn the ignition switch (18, Fig. B) to “0” position.

4.Disengage the retainers (8 and 6) and open the right and left doors (7 and 5, Fig. C).

5.Check the side skirt (2, Fig. F) integrity.

Replace the skirts when they have cuts (1, Fig. Q) larger than 0.79 in (20 mm) or cracks/tears (2) larger than 0.39 in (10 mm) (for skirt replacement, refer to the Service Manual).

6.Check that side skirt (2, Fig. F) height from ground is within 0 – 0.12 in (0 – 3 mm) (Fig. R).

After loosening the screws (3, Fig. F), if necessary, adjust the skirt position. Then tighten the screws (3).

Front and rear skirt

7.Remove the main broom, as described in the related paragraph.

8.Check the front and rear skirts (1 and 2, Fig. W) for integrity.

Replace the skirts when they have cuts (1, Fig. Q) larger than 0.79 in (20 mm) or cracks/tears (2) larger than 0.39 in (10 mm) (for skirt replacement, refer to the Service Manual).

9.Check that the front and rear skirts (1 and 2, Fig. W) rub lightly on the floor but are not completely lifted from the ground (see figure S).

After loosening the screws (3, Fig. W), if necessary, adjust the skirt position. Then tighten the screws (3).

10.Press the front (25, Fig. B) skirt lifting pedal completely, and check that the front skirt lifts 1.97 in (50 mm) approximately.

Release the pedal and check that the skirt returns to the initial position and not in an intermediate position. If necessary, adjust the skirt lifting cable (1, Fig. X) by using the adjuster (2) on the left front side of the skirt (for the front skirt control cable replacement, refer to the Service Manual).

11.Reassemble all the components in the reverse order of disassembly.

HOPPER LIFTING SYSTEM HYDRAULIC OIL LEVEL CHECK

CAUTION!

These operations must be performed with the hopper (4, Fig. C) in its original position (as shown in the figure).

1.Engage the parking brake by means of the pedal and the lever (26 and 19, Fig. B).

2.Open the hood (1, Fig. V) and hold it by using the related rod (16, Fig. V).

3.Check that the hydraulic oil level in the tank (14, Fig. V) is between the MIN and MAX indicators (as shown in Fig. Y).

4.If necessary add hydraulic oil - viscosity grade 32 cSt - through the plug (1, Fig. Y).

5.Disengage to lock rod (16, Fig. V) and close the hood (1, Fig. V).

BATTERY CHARGING

WARNING!

Battery charging produces explosive hydrogen gas. Charge the batteries only in well-ventilated areas and far from naked flames.

Do not smoke during battery charging. Keep the hood open while recharging the battery.

WARNING!

Be extremely careful when charging the batteries as there may be battery fluid leakages. The battery fluid is corrosive. If it comes in contact with the skin or the eyes, rinse thoroughly with water and consult a doctor.

1.Drive the machine on a level ground and engage the parking brake by means of the pedal and the lever (26 and 19, Fig. B).

2.Turn the ignition switch (18, Fig. B) to “0” position.

3.Open the hood (13, Fig. C) and hold it by using the related rod (16, Fig. V).

4.Check the correct level of electrolyte inside the batteries; if necessary, top up through the caps (3, Fig. V).

Leave the caps (3) open for the next recharging. Clean, if necessary, the upper surface of the batteries.

5.Check that the battery charger is appropriate, referring to the Battery Charger Operating Manual. The battery charger voltage rating is 24 V.

The battery charger must be appropriate for the battery installed on the machine.

14

Terra™ 5200B – 146 1996 000(2)2004-08

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Mode D’EMPLOI ET D’ENTRETIEN Instructions for USEInstrucciones DE USO Instruções DE USO14 15 Terra 5200B 146 1996Maintenance Safety FunctionsTroubleshooting Scrapping Instructions for USE IntroductionIntroduction Instructions for USE General Instructions UnpackingMachine Description Terra 5200B Sweeper OperationConventions DescriptionInstructions for USE Technical Data Wiring diagram See Fig. AFACCESSORIES/OPTIONS Battery CHECK/SETTING on a NEW MachineUSE FusesBattery Installation and WET or GEL Battery Setting Battery installationWET or GEL battery setting Before Machine START-UPInstructions for USE Starting and Stopping the Machine Machine OperationStarting the machine Stopping the machineWorking Light Adjustment Instructions for USE Hopper DumpingMachine Long Inactivity First Period of USEMaintenance Scheduled Maintenance TableBrooms of various hardness are available This procedure is applicable to all types BroomsTighten the locknut 2, Fig. E Brooms of various hardness are available Remove the internal pocket separator 7, Fig. AC Battery Charging Skirt Height and Operation CheckHopper Lifting System Hydraulic OIL Level Check Side skirtSafety Functions TroubleshootingScrapping Instrucciones DE USO Introducción Descripción DE LA MáquinaUSO MantenimientoIntroducción Instrucciones DE USO Instrucciones Generales DesembalajeConvenciones Descripción DE LA MáquinaDescripción Esquema eléctrico Véase Fig. AF Instrucciones DE USO Datos TécnicosCódigos colores BK Negro BU Azul BN Marrón GN Verde GY Gris USO FusiblesACCESORIOS/OPCIONES CONTROL/PREPARACIÓN Baterías EN LA Máquina NuevaAntes DE LA Puesta EN Marcha DE LA Máquina Sin bateríasInstalación de las baterías Regulación de batería WET o GELPuesta en marcha Máquina EN FunciónParada de la máquina Máquina Ajuste DE LA LUZ DE TrabajoPeriodo DE Larga Inactividad DE LA Primer Periodo DE UtilizaciónMantenimiento Esquema DE Mantenimiento ProgramadoHay cepillos con cerdas más o menos Mm 0,79 1,57Instrucciones DE USO Control Y Ajuste DE LA Altura DEL Cepillo Lateral LateralesLos filtros de bolsas de fibra de poliéster Necesitan una limpieza mucho másAdemás del filtro de papel estándar, hay Estos tipos Procedimiento siguienteCarga DE LAS Baterías Control Altura Y Funcionamiento DE LAS Puertas AbatiblesPuerta abatible lateral Funciones DE Seguridad Búsqueda AveríasInterruptor DE Asenso Marcha Pulsador DE EmergenciaEliminación Mode D’EMPLOI ET D’ENTRETIEN Introduction Description DE LA MachineUtilisation EntretienMode D’EMPLOI ET D’ENTRETIEN Symboles UtilisesBut ET Contenu DU Manuel DestinatairesMode Demploi ET Dentretien Instructions Generales Description DE LA Machine Mode D’EMPLOI ET D’ENTRETIEN DeballageCapacites Operationnelles DE Terra 5200B Mode Demploi ET Dentretien Caracteristiques Techniques Schéma électrique Voir Fig. AFBE1 Feu clignotant optionnel BZ1 ArrièreACCESSOIRES/OPTIONS UtilisationCONTROLE/PREPARATION DES Batteries SUR UNE Machine Nouvelle Avertissement ConsultationMode Demploi ET Dentretien Installation des batteriesAvant LA Mise EN Marche DE LA Machine Sans batteriesMachine AU Travail Mise en marcheDébloquer le volant 10, Fig. B au moyen du bouton Arrêt de la machineInactivite Prolongee DE LA Machine Reglage DU Phare DE TravailPremiere Periode Dutilisation Entretien Plan Recapitulatif Dentretien ProgrammeSerrer le contre-écrou 2, Fig. E Remplacement DES Brosses Laterales Controle ET Reglage DE LA Hauteur DES Brosses LateralesContrôler que le corps du filtre n’a pas de déchirures 12. Déposer le séparateur intérieur poches 7, Fig. ACControle DE LA Hauteur ET DU Fonctionnement DES Volets Chargement DES BatteriesVolets latéraux Volets avant et arrièreFonctions DE Securite Depistage DES PannesInterrupteur DE Marche BOUTON-POUSSOIR DurgenceMise EN Decharge Instruções DE USO Introdução Descrição DA MáquinaManutenção Funções DE SegurançaIntrodução Instruções DE USO Instruções Gerais DesempacotamentoDescrição DA Máquina Funcionamento DA Máquina DE Varrer Terra 5200BConvenções DescriçãoInstruções DE USO Dados Técnicos Esquema elétrico Ver a fig. AFTrás Códigos de coresVERIFICAÇÃO/CONFIGURAÇÃO DE Bateria EM UMA Máquina Nova FusíveisACESSÓRIOS/OPÇÕES Perigo Atenção Advertência ConsultaConfiguração das baterias WET ou GEL Instalação E Definição DE Bateria WET OU GELAntes DA Partida DA Máquina Baterias não fornecidasInstruções DE USO Partida E Parada DA Máquina Máquina EM FuncionamentoPartida da máquina Parada da máquinaAjuste DA LUZ DE Trabalho Desativação Prolongada DA MáquinaPeríodo Inicial DE USO Máquina está pronta para retomar o trabalhoManutenção Tabela DE Manutenção ProgramadaVerificação E Regulação DA Altura DA Vassoura CentralSão fornecidas vassouras com vários tipos Aperte a porca de aperto 2, fig. EInstruções DE USO Verificação E Regulação DA Altura DAS Vassouras LateraisOs filtros de bolsa em poliéster Ser aplicado a qualquer tipo Procedimento indicado a seguirQuando as superfícies de filtragem já não Forem adequadas, será necessárioCarregamento DA Bateria Verificação DA Altura E do Funcionamento DAS AbasAba lateral Funções DE Segurança Localização DE DefeitosInterruptor DE Consentimento DE Funcionamento Interruptor DE EmergênciaDescarte S310215 200 BAR Terra 5200B 146 1996 Nilfisk-Advance, Inc

5200B specifications

The Nilfisk-Advance America 5200B is a powerful and reliable walk-behind scrubber designed for efficiency and performance in a variety of cleaning environments. This machine is particularly well-suited for medium-sized to large facilities such as schools, hospitals, retail spaces, and warehouses, where cleanliness is paramount.

One of the standout features of the Nilfisk 5200B is its robust design, which incorporates durable materials to withstand the rigors of constant use. It boasts a compact frame that allows for excellent maneuverability in tight spaces while still maintaining a generous cleaning path. The machine is equipped with a 20-inch scrubbing width, enabling it to cover significant ground in a single pass.

The 5200B uses advanced scrub technologies that enhance its cleaning capabilities. One notable innovation is its dual brush system, which delivers superior scrubbing power and provides effective cleaning on various floor surfaces, including tile, concrete, and vinyl. The adjustable brush pressure feature allows operators to customize the scrubbing intensity based on the specific needs of the flooring and environment.

Efficiency is a key concern for any cleaning operation, and the 5200B addresses this through its impressive water management system. The machine is designed to optimize water usage, reducing waste and promoting eco-friendly cleaning practices. Its solution control feature allows for precise dispensing of cleaning solution, ensuring that the right amount is used for every job, further enhancing both efficacy and cost savings.

In terms of user comfort, the Nilfisk 5200B is equipped with an ergonomic handle and easy-to-use controls that minimize operator fatigue during extended cleaning sessions. The intuitive dashboard provides real-time feedback and monitoring, making it simple for users to track maintenance needs and performance metrics.

Another significant characteristic of the 5200B is its low noise level, which makes it ideal for use in noise-sensitive areas. This means that cleaning can be performed during business hours without disrupting customers or staff.

With its blend of robust construction, advanced cleaning technologies, and user-focused features, the Nilfisk-Advance America 5200B is an outstanding choice for organizations seeking an efficient and effective cleaning solution. This machine not only enhances cleanliness but also contributes to a safer and more pleasant environment for all who inhabit the spaces it cleans.
Top Page Image Contents