Black & Decker BDH1760SM To access the Lift Reach Head, To re-fit the Lift and Reach Head

Page 6

The Lift and Reach Head - Fig. G G

This Steam Mop incorporates a built in Lift

and Reach Head which enables you to access

tight corners and narrow gaps. CAUTION: Always wear suitable shoes

when accessing the Lift and Reach Head on your steam mop. Do not wear slippers or

open-toed footwear.

To access the Lift and

Reach Head:

• Return the handle to the upright position and turn the steam mop ‘OFF’.

• Place the steam mop on the resting mat and wait until it cools down. (approximately five minutes)

• Place the front of your shoe onto the steam head removal tab (15) and press down gently.

• Lift the Lift and Reach Head up off the steam head (5).

• Place the Lift and Reach Head cleaning pad (9) on the floor with the ‘hook & loop’ side facing up.

• Raise the Lift and Reach Head off the resting mat (7) and press it down onto the cleaning pad (9). You are now ready to steam clean and sanitize your floor.

To re-fit the Lift and Reach Head:

• Return the handle tube (4) to the upright position and turn the steam mop ‘OFF’.

• Place the steam mop on the resting mat and wait until it cools down. (approximately five minutes)

• Place the front of your shoe onto the Lift and Reach Head cleaning pad removal tab and press down firmly.

• Lift the Lift and Reach Head (16) up off the cleaning pad.

• Place the tip of the Lift and Reach Head into the steam head (5) and push downward. Ensure it is locked into place by gently pulling upwards on the handle.

NOTICE: Always place the steam mop on the resting mat (7) with the handle tube (4) in the upright position when stationary and make sure the steam mop is turned off when not in use.

Filling the water tank - Fig. H & I

This Steam Mop incorporates an anti-calcium system to help prolong the life of the system.

NOTICE: The water tank is conveniently removable for easier use.

NOTICE: Fill the water tank with regular tap water.

NOTICE: In areas of very hard water, the use of de-ionized water is recommended.

WARNING: Do not overfill the tank. Only fill to bottom of hole with water tank in vertical position.

• Ensure that the appliance is switched off and the power cord is disconnected from the power supply.

• Place the steam mop on the resting mat (7) with the handle tube (4) in the upright position.

• Remove the water tank (3) by pulling it upwards.

• Open the filler cap (18) by lifting it up.

• Fill the water tank (3) with water to the bottom of the hole with tank in vertical position.

• Close the filler cap.

• Re-install the water tank onto the steam mop body (11) and ensure it is firmly seated.

NOTICE: Always empty the water tank after use.

H

I

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Steam MOP Using your appliance Safety instructionsIntended use Residual risks Safety of othersInspection and repairs After useFunctional Description AssemblyAttaching the water tank Attaching the handle Fig. B & LAttaching the carpet glider Fig. F Attaching a cleaning pad Fig. DRemoving a cleaning pad Fig. E Removing the carpet gliderFilling the water tank Fig. H To access the Lift Reach HeadTo re-fit the Lift and Reach Head Lift and Reach Head Fig. G GSmartSelectTM Dial Fig. K Switching On and Off Fig. JOperation Steam Burst button Fig. KGeneral USE Steam cleaningAlways vacuum or sweep the floor before using the steam mop Carpet refreshingAccessories Maintenance and cleaningCare of the cleaning pads After use Fig. LTroubleshooting Problem Possible CausePossible Solution Service Information Limited Two-Year Home Use Warranty Balai à vapeur Avertissements DE Sécurité ET Directives Fiches Utilisation PrévueDirectives de sécurité PolariséesInspection et réparations Utilisation de l’appareilAprès usage Sécurité d’autruiDescription fonctionnelle MARCHE/ARRÊTAssemblage Fixation D’UN Tampon Nettoyant Fixation de la tête à vapeur Fig. CFixation DU Reservoir D’EAU Retrait D’UN Tampon Nettoyant Fig. EPour Acceder a LA Tête Lift and Reach Depose DU Patin a TapisLA Tête Lift and Reach Fig. G Pour Remettre LA Tête Lift and Reach EN PlaceFonctionnement Allumer ET Eteindre L’APPAREIL Fig. JCadran Smart SelectMC Fig. K Bouton DE JET DE Vapeur Fig. K Conseils Pour UNE Utilisation Optimale Usage GeneralNettoyage a LA Vapeur Rafraichir LES Tapis Apres Usage Fig. LEntretien ET Nettoyage Entretien DES Tampons Nettoyants AccessoiresCause possible Solution possible DépannageInformation sur les réparations Trapeador de vapor Advertencias E Instrucciones DE Seguridad Enchufes USO PrevistoInstrucciones de seguridad PolarizadosUso del artefacto Después del usoInspección y reparaciones Descripción de las funciones ENCENDIDO/ ApagadoEnsamblaje Extracción DE UNA Almohadilla DE Limpieza FIG. E Instalación DEL Tanque DE AguaInstalación DE UNA Almohadilla DE Limpieza FIG. D Instalación DEL Deslizador Para Alfombras FIG. FPara Acceder AL Cabezal Extracción DEL Deslizador Para AlfombrasEL Cabezal LIFT&REACH FIG. G LIFT&REACHEncendido Y Apagado FIG. J Llenado DEL Tanque DE Agua FIG. HOperación Dial SmartSelectTM Fig. KBotón DE Ráfaga DE Vapor FIG. K Consejos Para UN USO ÓptimoUSO General Limpieza CON Vapor Renovación DE AlfombrasCuidado DE LAS Almohadillas DE Limpieza Después DEL USO FIG. LMantenimiento Y Limpieza AccesoriosCausa posible Solución posible Detección de problemasProblema Solamente para Propósitos de MéxicoPage Años DE Garantia Esta Garantia no Aplica CuandoFernando González Armenta Htas. Portátiles de ChihuahuaFerre Pat de Puebla, S.A. de C.V Perfiles y Herramientas de Morelia
Top Page Image Contents