KitchenAid W10515677C manual ICE Maker USE, How Your Ice Maker Works, Using the Controls

Page 11

Replace the Water Filter

To purchase a replacement water filter, see “Accessories.”

Replace the disposable water filter when indicated on the water filter status display or at least every 9 months. If the ice making rate decreases before the Replace Filter light illuminates, then replace the filter.

1.Locate the water filter compartment in the right-hand side of the control housing. See Step 3 in the “Install Water Filter” section.

2.Turn the water filter counterclockwise (to the left), and pull it straight out of the compartment.

NOTE: There may be some water in the filter. Some spilling may occur.

3.Install the replacement water filter by following steps 2 through 5 in the “Install the Water Filter” section.

ICE MAKER USE

How Your Ice Maker Works

When you first start your ice maker, the water pan will fill and the system will rinse itself before starting to make ice. The rinsing process takes about 5 minutes.

Under normal operating conditions, the ice maker will cycle at preset temperatures. The ice level sensor located in the ice storage bin will monitor the ice levels.

IMPORTANT: If the water supply to the ice maker is turned off, be sure to set the ice maker control to OFF.

5.Cubes fall into the storage bin. When the bin is full, the ice maker shuts off automatically and restarts when more ice is needed. The ice bin is not refrigerated, and some melting will occur. The amount of melting varies with room temperature.

The Ice Making Process

1.Water is constantly circulated over a freezing plate. As the water freezes into ice, the minerals in the water are rejected. This produces a sheet of ice with a low mineral content.

2.When the desired thickness is reached, the ice sheet is released and slides onto a cutter grid. The grid divides the sheet into individual cubes.

3.The water containing the rejected minerals is drained after each freezing cycle.

4.Fresh water enters the machine for the next ice making cycle.

NOTE: As the room and water temperatures vary, so will the amount of ice produced and stored. This means that higher operating temperatures result in reduced ice production.

Using the Controls

1.To start ice production, press ON/OFF.

2.To stop ice maker operation, press ON/OFF.

NOTES:

■Pressing the On/Off button does not shut off power to the ice maker.

■Allow 24 hours to produce the first batch of ice. Discard the first 2 batches produced.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Guide d’utilisation et d’entretien Use & Care GuideManual de uso y cuidado Table DES Matières Table of ContentsÍndice Unpack the Ice Maker ICE Maker SafetyInstallation Instructions Cleaning Before UseRecommended Grounding Method Location RequirementsElectrical Requirements Connect Water Supply Water Supply RequirementsVacation or Extended Time Without Use Kit Contains Drain Pump InstallationIf Ice Maker Is Currently Installed Rear ViewDrain Tube Drain Pump InstallationWater Supply Line Rear PanelVent Tube Drain Pump InstalledDrain Pump Mounting Tab Slot Leveling Drain ConnectionWater Filter Status Light Install the Water FilterWater Filtration System Replace the Water Filter Using the ControlsICE Maker USE How Your Ice Maker WorksNormal Sounds CleaningICE Maker Care Interior Components Condenser Dirty or Clogged CondenserTo Shut Down the Ice Maker For Ice Makers with a Drain Pump InstalledVacation and Moving Care Ice Maker Seems Noisy TroubleshootingIce Maker Operation Produces No Ice Ice ProductionIce Maker Runs But Our Consultants Provide Assistance With If you need replacement partsU.S.A CanadaAccessories Performance Data SheetDisclaimer of Representations Outside of Warranty Kitchenaid ICE Maker WarrantyThree Year Limited Warranty Parts and Labor Items Excluded from WarrantyPage Su seguridad y la seguridad de los demás es muy importante Seguridad DE LA Fábrica DE HieloRequisitos eléctricos Instrucciones DE InstalaciónDesempaque la fábrica de hielo Requisitos de ubicaciónConexión del suministro de agua Requisitos del suministro de aguaVacaciones o tiempo prolongado sin uso El juego contiene Instalación de la bomba de desagüeVista posterior Instalación de la bomba de desagüe Si la fábrica de hielo ya está instaladaTapa de desagüe Línea de suministro de aguaBomba de desagüe instalada Tubo de desagüeUbicaciones de las piezas Ranura de la lengüeta de montaje de la bomba de desagüeVista lateral Conexión del desagüeTubo de ventilación Sistema de desagüe por gravedadConexión del desagüe NivelaciónSistema de la bomba de desagüe en algunos modelos Luz de estado del filtro de agua Sistema de filtración de aguaInstalación del filtro de agua Reemplazo del filtro de agua USO DE LA Fábrica DE HieloCómo funciona su fábrica de hielo Uso de los controlesLimpieza Cuidado DE LA Fábrica DE HieloSonidos normales Bandeja de agua Tapón de desagüe Condensador Un condensador sucio u obstruidoTornillo Espaciador de plástico Rejilla de corte Componentes interioresPara apagar la fábrica de hielo Cuidado durante las vacaciones y mudanzasFunciona Solución DE ProblemasFuncionamiento de la fábrica de hielo La fábrica de hielo noCalidad del hielo Producción de hieloSi necesita piezas de repuesto Problemas de plomeríaAyuda O Servicio Técnico En los EE.UULimpiador Hoja DE Datos DEL RendimientoAccesorios Filtro de aguaExclusión DE Garantías Implícitas Garantía DE LA Fábrica DE Hielo DE KitchenaidExclusiones DE LA Garantía Esta garantía limitada no cubrePage Votre sécurité et celle des autres est très importante Sécurité DE LA Machine À GlaçonsSpécifications électriques Instructions D’INSTALLATIONExigences d’installation Déballage de la machine à glaçonsRaccordement à la canalisation d’eau Spécifications de l’alimentation en eauVacances ou longue période d’inutilisation Contenu de l’ensemble Installation de la pompe de vidangeVue arrière Canalisation d’alimentation en eau Si la machine à glaçons est installéeInstallation de la pompe de vidange Bouchon de vidangeTube de vidange Pompe de vidange installéeVue latérale Raccordement au conduit vidangeTube de ventilation Système de vidange par gravitéRaccordement du conduit dévacuation NivellementSystème avec pompe de vidange sur certains modèles Témoin lumineux de l’état du filtre à eau Installer le filtre à eauSystème de filtration d’eau Fonctionnement de la machine à glaçons Utilisation des commandesRemplacement du filtre à eau Utilisation DE LA Machine À GlaçonsNettoyage Entretien DE LA Machine À GlaçonsBruits normaux Condenseur Un condenseur sale ou obstrué Composants intérieurs Machine à glaçons avec pompe de vidange Précautions à prendre pour les vacances ou le déménagementArrêt de la machine à glaçons Dépannage Qualité des glaçons Production de glaçonsAu Canada Assistance OU ServiceProblèmes de plomberie Aux États-UnisNettoyant AccessoiresFeuille DE Données SUR LA Performance Filtre à eauLa présente garantie limitée ne couvre pas Garantie DE LA Machine À Glaçons KitchenaidGarantie Limitée DE Trois ANS Pièces ET MAIN-D’ŒUVRE Éléments Exclus DE LA GarantieW10515677C

W10515677C specifications

The KitchenAid W10515677C is a versatile and essential component for any home chef who prioritizes both quality and performance in their kitchen tools. This food processor attachment, designed for use with KitchenAid stand mixers, enhances the functionality of the mixer by providing a reliable and efficient method for food preparation.

One of the standout features of the W10515677C is its powerful chopping and slicing capability. With sharp stainless-steel blades, this attachment allows for precise and consistent cuts, whether you're dicing vegetables, grating cheese, or slicing meats. The adjustable slicing disc provides multiple thickness options, making it easy to achieve the desired texture for your ingredients.

The design of the W10515677C is user-friendly, featuring an easy-to-assemble construction that ensures quick setup and minimal hassle. Once attached to the stand mixer, it operates seamlessly, allowing users to focus on their culinary creativity without worrying about the intricacies of food prep.

Another significant characteristic of this attachment is its generous capacity. It can handle large quantities of ingredients, making it perfect for meal preps or when cooking for a crowd. This efficiency saves time and simplifies the cooking process, allowing you to enjoy more time with family and friends.

Safety is also a key consideration in the design of the W10515677C. The attachment features a safety latch that keeps it securely attached to the stand mixer during operation. Additionally, the component comes with a push tool that ensures your hands are kept safely away from the blades while processing food.

Cleaning and maintenance are made straightforward, as most parts of the W10515677C are dishwasher safe, facilitating an easy cleanup after use. This attachment exemplifies KitchenAid’s commitment to durability and quality, built to withstand frequent use in busy kitchens.

In summary, the KitchenAid W10515677C food processor attachment elevates the experience of cooking at home. With its sharp stainless-steel blades, adjustable slicing capabilities, ease of use, and safety features, it stands as a reliable ally in meal preparation. Expanding the capabilities of your KitchenAid stand mixer, this attachment is a practical investment for anyone looking to enhance their culinary skills.
Top Page Image Contents