KitchenAid W10515677C manual Vacation and Moving Care, To Shut Down the Ice Maker

Page 14

NOTE: Make sure the plastic spacer from the right-hand side of the cutter grid bracket stays with the cutter grid.

 

D

A

 

B

E

C

F

 

A. Cutter grid harness

D. Ice level sensor harness

B. Screw

E. Plastic spacer

C. Cutter grid

F. Screw

8.Remove the mounting screw that holds the water pan in place. Pull out on the front of the water pan.

9.Disconnect the pump bracket from the water pan and unplug the water pan drain pump.

A

 

B

D

C

 

A. Water pan

C. Drain cap

B. Water pan screw

D. Drain pump cover

10.Remove, clean and replace the ice scoop and ice scoop holder.

NOTE: On some models, the ice scoop holder is located in the upper left of the unit, and on other models, the ice scoop holder is located in the lower left of the unit.

After removing the ice scoop, remove the holder by removing the 2 screws.

NOTE: On some models, remove the holder by lifting up on the ice scoop holder and then out.

Wash the ice scoop holder along with the other interior components using the following instructions.

Replace the ice scoop holder by replacing the screws or on some models, pushing in on the holder and then down.

A

A. Ice scoop holder

11.Wash the interior components (cutter grid, exterior of hoses, and water pan) and the storage bin, door gasket, ice scoop, and ice scoop holder with mild soap or detergent and warm water. Rinse in clean water. Then clean the same parts with a solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L) warm water. Rinse again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts in dishwasher. They cannot withstand temperatures above 145°F (63°C).

12.To replace the water pan, set the water pan inside the ice bin. Hook up the water pan pump. Snap the pump bracket back onto the water pan and place back into position. Secure the water pan by replacing the mounting screw.

13.Check the following:

Drain cap from the water pan is securely in place. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

Hose from water pan is inserted into storage bin drain opening.

14.Slide the cutter grid back into place and secure it by replacing the right-hand screw and plastic spacer. Then tighten the left-hand screw. Reconnect the cutter grid harness and the ice level sensor harness.

15.Replace the cutter grid cover using the screw that was removed earlier.

16.Gently wipe the control panel with a soft, clean dishcloth using warm water and a mild liquid dish detergent.

17.Plug in ice maker or reconnect power.

18.After cleaning, make sure that all controls are set properly and that no control indicators are flashing.

Vacation and Moving Care

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

To Shut Down the Ice Maker:

1.Unplug ice maker or disconnect power.

2.Remove all ice from storage bin.

3.Shut off the water supply.

4.Remove the 2 screws in the lower access panel and the

2 screws from the base grille area of the front panel support. Pull forward to remove the lower access panel.

A

A

B

B

A. Lower access panel screws

B. Base grille screws

5.Disconnect the inlet and outlet lines to water valve. Allow these lines to drain and then reconnect to the valve.

6.Replace lower access panel and screws.

7.Drain water from water pan by removing the drain cap.

8.If the room temperature will drop below 32°F (0°C), water must be removed from the drain line.

For Ice Makers with a Drain Pump Installed:

Plug in ice maker or reconnect power.

Turn ice maker off and remove all remaining ice from ice bin.

14

Image 14
Contents Guide d’utilisation et d’entretien Use & Care GuideManual de uso y cuidado Table DES Matières Table of ContentsÍndice Cleaning Before Use ICE Maker SafetyInstallation Instructions Unpack the Ice MakerRecommended Grounding Method Location RequirementsElectrical Requirements Connect Water Supply Water Supply RequirementsVacation or Extended Time Without Use Rear View Drain Pump InstallationIf Ice Maker Is Currently Installed Kit ContainsRear Panel Drain Pump InstallationWater Supply Line Drain TubeVent Tube Drain Pump InstalledDrain Pump Mounting Tab Slot Drain Connection LevelingWater Filter Status Light Install the Water FilterWater Filtration System How Your Ice Maker Works Using the ControlsICE Maker USE Replace the Water FilterNormal Sounds CleaningICE Maker Care Condenser Dirty or Clogged Condenser Interior ComponentsTo Shut Down the Ice Maker For Ice Makers with a Drain Pump InstalledVacation and Moving Care Ice Maker Seems Noisy TroubleshootingIce Maker Operation Produces No Ice Ice ProductionIce Maker Runs But Canada If you need replacement partsU.S.A Our Consultants Provide Assistance WithPerformance Data Sheet AccessoriesItems Excluded from Warranty Kitchenaid ICE Maker WarrantyThree Year Limited Warranty Parts and Labor Disclaimer of Representations Outside of WarrantyPage Seguridad DE LA Fábrica DE Hielo Su seguridad y la seguridad de los demás es muy importanteRequisitos de ubicación Instrucciones DE InstalaciónDesempaque la fábrica de hielo Requisitos eléctricosConexión del suministro de agua Requisitos del suministro de aguaVacaciones o tiempo prolongado sin uso El juego contiene Instalación de la bomba de desagüeVista posterior Línea de suministro de agua Si la fábrica de hielo ya está instaladaTapa de desagüe Instalación de la bomba de desagüeRanura de la lengüeta de montaje de la bomba de desagüe Tubo de desagüeUbicaciones de las piezas Bomba de desagüe instaladaSistema de desagüe por gravedad Conexión del desagüeTubo de ventilación Vista lateralConexión del desagüe NivelaciónSistema de la bomba de desagüe en algunos modelos Luz de estado del filtro de agua Sistema de filtración de aguaInstalación del filtro de agua Uso de los controles USO DE LA Fábrica DE HieloCómo funciona su fábrica de hielo Reemplazo del filtro de aguaLimpieza Cuidado DE LA Fábrica DE HieloSonidos normales Condensador Un condensador sucio u obstruido Bandeja de agua Tapón de desagüeComponentes interiores Tornillo Espaciador de plástico Rejilla de corteCuidado durante las vacaciones y mudanzas Para apagar la fábrica de hieloLa fábrica de hielo no Solución DE ProblemasFuncionamiento de la fábrica de hielo FuncionaProducción de hielo Calidad del hieloEn los EE.UU Problemas de plomeríaAyuda O Servicio Técnico Si necesita piezas de repuestoFiltro de agua Hoja DE Datos DEL RendimientoAccesorios LimpiadorEsta garantía limitada no cubre Garantía DE LA Fábrica DE Hielo DE KitchenaidExclusiones DE LA Garantía Exclusión DE Garantías ImplícitasPage Sécurité DE LA Machine À Glaçons Votre sécurité et celle des autres est très importanteDéballage de la machine à glaçons Instructions D’INSTALLATIONExigences d’installation Spécifications électriquesRaccordement à la canalisation d’eau Spécifications de l’alimentation en eauVacances ou longue période d’inutilisation Contenu de l’ensemble Installation de la pompe de vidangeVue arrière Bouchon de vidange Si la machine à glaçons est installéeInstallation de la pompe de vidange Canalisation d’alimentation en eauPompe de vidange installée Tube de vidangeSystème de vidange par gravité Raccordement au conduit vidangeTube de ventilation Vue latéraleRaccordement du conduit dévacuation NivellementSystème avec pompe de vidange sur certains modèles Témoin lumineux de l’état du filtre à eau Installer le filtre à eauSystème de filtration d’eau Utilisation DE LA Machine À Glaçons Utilisation des commandesRemplacement du filtre à eau Fonctionnement de la machine à glaçonsNettoyage Entretien DE LA Machine À GlaçonsBruits normaux Condenseur Un condenseur sale ou obstrué Composants intérieurs Machine à glaçons avec pompe de vidange Précautions à prendre pour les vacances ou le déménagementArrêt de la machine à glaçons Dépannage Production de glaçons Qualité des glaçonsAux États-Unis Assistance OU ServiceProblèmes de plomberie Au CanadaFiltre à eau AccessoiresFeuille DE Données SUR LA Performance NettoyantÉléments Exclus DE LA Garantie Garantie DE LA Machine À Glaçons KitchenaidGarantie Limitée DE Trois ANS Pièces ET MAIN-D’ŒUVRE La présente garantie limitée ne couvre pasW10515677C

W10515677C specifications

The KitchenAid W10515677C is a versatile and essential component for any home chef who prioritizes both quality and performance in their kitchen tools. This food processor attachment, designed for use with KitchenAid stand mixers, enhances the functionality of the mixer by providing a reliable and efficient method for food preparation.

One of the standout features of the W10515677C is its powerful chopping and slicing capability. With sharp stainless-steel blades, this attachment allows for precise and consistent cuts, whether you're dicing vegetables, grating cheese, or slicing meats. The adjustable slicing disc provides multiple thickness options, making it easy to achieve the desired texture for your ingredients.

The design of the W10515677C is user-friendly, featuring an easy-to-assemble construction that ensures quick setup and minimal hassle. Once attached to the stand mixer, it operates seamlessly, allowing users to focus on their culinary creativity without worrying about the intricacies of food prep.

Another significant characteristic of this attachment is its generous capacity. It can handle large quantities of ingredients, making it perfect for meal preps or when cooking for a crowd. This efficiency saves time and simplifies the cooking process, allowing you to enjoy more time with family and friends.

Safety is also a key consideration in the design of the W10515677C. The attachment features a safety latch that keeps it securely attached to the stand mixer during operation. Additionally, the component comes with a push tool that ensures your hands are kept safely away from the blades while processing food.

Cleaning and maintenance are made straightforward, as most parts of the W10515677C are dishwasher safe, facilitating an easy cleanup after use. This attachment exemplifies KitchenAid’s commitment to durability and quality, built to withstand frequent use in busy kitchens.

In summary, the KitchenAid W10515677C food processor attachment elevates the experience of cooking at home. With its sharp stainless-steel blades, adjustable slicing capabilities, ease of use, and safety features, it stands as a reliable ally in meal preparation. Expanding the capabilities of your KitchenAid stand mixer, this attachment is a practical investment for anyone looking to enhance their culinary skills.