KitchenAid W10515677C manual Location Requirements, Electrical Requirements

Page 4

Location Requirements

■To ensure proper ventilation for your ice maker, the front side must be completely unobstructed. The ice maker may be closed-in on the top and three sides, but the installation should allow the ice maker to be pulled forward for servicing if necessary.

■Installation of the ice maker requires a cold water supply inlet of ¹⁄₄" (6.35 mm) OD soft copper tubing with a shutoff valve or a Whirlpool supply line Part Number 8212547RB, and a Whirlpool approved drain pump, Part Number 1901A, only to carry the water to an existing drain.

■Choose a well ventilated area with temperatures above 55°F (13°C) and below 100°F (38°C). Best results are obtained between 70°F and 90°F (21ºC and 32°C).

■This ice maker must be installed in an area sheltered from the elements, such as wind, rain, water spray or drips.

■When installing the ice maker under a counter, follow the recommended opening dimensions shown. Place electrical and plumbing fixtures in the recommended location as shown.

NOTES:

■Check that the power supply cord is not damaged, or pinched or kinked between the ice maker and the cabinet.

■Check that the water supply line is not damaged, or pinched or kinked between the ice maker and the cabinet.

■Check that the drain line (on some models) is not damaged, or pinched or kinked between the ice maker and the cabinet.

 

 

14¹⁄₂"

A

 

 

(36.8 cm)

34"

 

 

 

(86.4 cm)

 

 

 

Min.

 

 

28¹⁄₂"

34¹⁄₂"

 

 

 

 

(72.4 cm)

(87.6 cm)

 

9"

3¹⁄₂"

 

Max.

 

 

 

 

(8.9 cm)(22.9 cm)

 

 

24"

 

B

 

 

 

 

(60.1 cm)

 

 

 

18"

 

 

(45.7 cm)

 

A. Recommended location for electrical and plumbing fixtures B. Floor level

■Choose a location where the floor is even. It is important for the ice maker to be level in order to work properly. If needed, you can adjust the height of the ice maker by changing the height of the leveling legs. See the “Leveling” section.

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your ice maker into its final location, it is important to make sure you have the proper electrical connection:

A 115 volt, 60 Hz., AC only, 15- or 20-amp electrical supply, properly grounded in accordance with the National Electrical Code and local codes and ordinances, is required.

It is recommended that a separate circuit, serving only your ice maker, be provided. Use a receptacle which cannot be turned off by a switch or pull chain.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter) equipped outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Ice quality may be affected. If nuisance tripping has occurred, and if the condition of the ice appears poor, dispose of it.

Recommended Grounding Method

The ice maker must be grounded. The ice maker is equipped with a power supply cord having a 3 prong grounding plug. The cord must be plugged into a mating, 3 prong, grounding-type wall receptacle, grounded in accordance with the National Electrical Code and local codes and ordinances. If a mating wall receptacle is not available, it is the personal responsibility of the customer to have a properly grounded, 3 prong wall receptacle installed by a qualified electrician.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Manual de uso y cuidado Use & Care GuideGuide d’utilisation et d’entretien Índice Table of ContentsTable DES Matières ICE Maker Safety Installation InstructionsCleaning Before Use Unpack the Ice MakerElectrical Requirements Location RequirementsRecommended Grounding Method Vacation or Extended Time Without Use Water Supply RequirementsConnect Water Supply Drain Pump Installation If Ice Maker Is Currently InstalledRear View Kit ContainsDrain Pump Installation Water Supply LineRear Panel Drain TubeDrain Pump Mounting Tab Slot Drain Pump InstalledVent Tube Drain Connection LevelingWater Filtration System Install the Water FilterWater Filter Status Light Using the Controls ICE Maker USEHow Your Ice Maker Works Replace the Water FilterICE Maker Care CleaningNormal Sounds Condenser Dirty or Clogged Condenser Interior ComponentsVacation and Moving Care For Ice Makers with a Drain Pump InstalledTo Shut Down the Ice Maker Ice Maker Operation TroubleshootingIce Maker Seems Noisy Ice Maker Runs But Ice ProductionProduces No Ice If you need replacement parts U.S.ACanada Our Consultants Provide Assistance WithPerformance Data Sheet AccessoriesKitchenaid ICE Maker Warranty Three Year Limited Warranty Parts and LaborItems Excluded from Warranty Disclaimer of Representations Outside of WarrantyPage Seguridad DE LA Fábrica DE Hielo Su seguridad y la seguridad de los demás es muy importanteInstrucciones DE Instalación Desempaque la fábrica de hieloRequisitos de ubicación Requisitos eléctricosVacaciones o tiempo prolongado sin uso Requisitos del suministro de aguaConexión del suministro de agua Vista posterior Instalación de la bomba de desagüeEl juego contiene Si la fábrica de hielo ya está instalada Tapa de desagüeLínea de suministro de agua Instalación de la bomba de desagüeTubo de desagüe Ubicaciones de las piezasRanura de la lengüeta de montaje de la bomba de desagüe Bomba de desagüe instaladaConexión del desagüe Tubo de ventilaciónSistema de desagüe por gravedad Vista lateralSistema de la bomba de desagüe en algunos modelos NivelaciónConexión del desagüe Instalación del filtro de agua Sistema de filtración de aguaLuz de estado del filtro de agua USO DE LA Fábrica DE Hielo Cómo funciona su fábrica de hieloUso de los controles Reemplazo del filtro de aguaSonidos normales Cuidado DE LA Fábrica DE HieloLimpieza Condensador Un condensador sucio u obstruido Bandeja de agua Tapón de desagüeComponentes interiores Tornillo Espaciador de plástico Rejilla de corteCuidado durante las vacaciones y mudanzas Para apagar la fábrica de hieloSolución DE Problemas Funcionamiento de la fábrica de hieloLa fábrica de hielo no FuncionaProducción de hielo Calidad del hieloProblemas de plomería Ayuda O Servicio TécnicoEn los EE.UU Si necesita piezas de repuestoHoja DE Datos DEL Rendimiento AccesoriosFiltro de agua LimpiadorGarantía DE LA Fábrica DE Hielo DE Kitchenaid Exclusiones DE LA GarantíaEsta garantía limitada no cubre Exclusión DE Garantías ImplícitasPage Sécurité DE LA Machine À Glaçons Votre sécurité et celle des autres est très importanteInstructions D’INSTALLATION Exigences d’installationDéballage de la machine à glaçons Spécifications électriquesVacances ou longue période d’inutilisation Spécifications de l’alimentation en eauRaccordement à la canalisation d’eau Vue arrière Installation de la pompe de vidangeContenu de l’ensemble Si la machine à glaçons est installée Installation de la pompe de vidangeBouchon de vidange Canalisation d’alimentation en eauPompe de vidange installée Tube de vidangeRaccordement au conduit vidange Tube de ventilationSystème de vidange par gravité Vue latéraleSystème avec pompe de vidange sur certains modèles NivellementRaccordement du conduit dévacuation Système de filtration d’eau Installer le filtre à eauTémoin lumineux de l’état du filtre à eau Utilisation des commandes Remplacement du filtre à eauUtilisation DE LA Machine À Glaçons Fonctionnement de la machine à glaçonsBruits normaux Entretien DE LA Machine À GlaçonsNettoyage Condenseur Un condenseur sale ou obstrué Composants intérieurs Arrêt de la machine à glaçons Précautions à prendre pour les vacances ou le déménagementMachine à glaçons avec pompe de vidange Dépannage Production de glaçons Qualité des glaçonsAssistance OU Service Problèmes de plomberieAux États-Unis Au CanadaAccessoires Feuille DE Données SUR LA PerformanceFiltre à eau NettoyantGarantie DE LA Machine À Glaçons Kitchenaid Garantie Limitée DE Trois ANS Pièces ET MAIN-D’ŒUVREÉléments Exclus DE LA Garantie La présente garantie limitée ne couvre pasW10515677C

W10515677C specifications

The KitchenAid W10515677C is a versatile and essential component for any home chef who prioritizes both quality and performance in their kitchen tools. This food processor attachment, designed for use with KitchenAid stand mixers, enhances the functionality of the mixer by providing a reliable and efficient method for food preparation.

One of the standout features of the W10515677C is its powerful chopping and slicing capability. With sharp stainless-steel blades, this attachment allows for precise and consistent cuts, whether you're dicing vegetables, grating cheese, or slicing meats. The adjustable slicing disc provides multiple thickness options, making it easy to achieve the desired texture for your ingredients.

The design of the W10515677C is user-friendly, featuring an easy-to-assemble construction that ensures quick setup and minimal hassle. Once attached to the stand mixer, it operates seamlessly, allowing users to focus on their culinary creativity without worrying about the intricacies of food prep.

Another significant characteristic of this attachment is its generous capacity. It can handle large quantities of ingredients, making it perfect for meal preps or when cooking for a crowd. This efficiency saves time and simplifies the cooking process, allowing you to enjoy more time with family and friends.

Safety is also a key consideration in the design of the W10515677C. The attachment features a safety latch that keeps it securely attached to the stand mixer during operation. Additionally, the component comes with a push tool that ensures your hands are kept safely away from the blades while processing food.

Cleaning and maintenance are made straightforward, as most parts of the W10515677C are dishwasher safe, facilitating an easy cleanup after use. This attachment exemplifies KitchenAid’s commitment to durability and quality, built to withstand frequent use in busy kitchens.

In summary, the KitchenAid W10515677C food processor attachment elevates the experience of cooking at home. With its sharp stainless-steel blades, adjustable slicing capabilities, ease of use, and safety features, it stands as a reliable ally in meal preparation. Expanding the capabilities of your KitchenAid stand mixer, this attachment is a practical investment for anyone looking to enhance their culinary skills.
Top Page Image Contents