KitchenAid W10515677C manual Drain Pump Mounting Tab Slot, Drain Pump Installed, Vent Tube

Page 8

Drain Pump Mounting Tab Slot

A

A. Mounting tab slot

Drain Pump Installed

A

A. Drain pump installed

8.Align the 2 screw holes at the rear of the pump. Use two #8-32 x ³⁄₈" screws, supplied. See “Parts Locations” illustration.

9.Connect drain tube to ice maker bin outlet (⁵⁄₈" ID), using ⁷⁄₈" adjustable clamp, supplied. See “Drain Tube” illustration.

10.Coil ice maker power cord into a 4" (10.2 cm) diameter coil. Wrap electrical tape around the power cord in several places to keep the cord in a coil. Locate coiled power cord between the drain pump and side of enclosure and plug into the receptacle of the drain pump. See “Parts Locations” illustration.

11.Attach the drain pump power cord to ice maker unit base with clamp and screw (removed in Step 6) that was used to attach ice maker power cord. See “Parts Locations” illustration.

12.Place new rear panel (small one for 15" ice makers, large one for 18") against the back of the ice maker. Route the vent tube and drain pump discharge tube through cutouts in the rear panel.

13.Secure rear panel with original screws. See “Rear Panel” illustration.

14.Secure vent tube to back of ice maker using 3 clamps and three #8-32 x ³⁄₈" screws, supplied. See “Vent Tube” illustration.

Vent Tube

NOTE: Do not pinch, kink or damage the vent tube. Check that it is not damaged, or pinched or kinked between the cabinet and the ice maker.

A

B

A. Vent tube

B. Clamps and screws

15.Attach ¹⁄₂" ID x 10 ft (3 m) drain tube to pump discharge tube. See “Parts Locations” illustration.

16.Connect ice maker to water supply and install ice maker as specified by the product installation instructions.

17.Check all connections for leaks.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

18.Plug in ice maker or reconnect power.

19.Turn on ice maker.

20.Wait for rinsing cycle, approximately 5 minutes, to be sure the ice maker is operating properly.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Guide d’utilisation et d’entretien Use & Care GuideManual de uso y cuidado Table DES Matières Table of ContentsÍndice ICE Maker Safety Installation InstructionsCleaning Before Use Unpack the Ice MakerRecommended Grounding Method Location RequirementsElectrical Requirements Connect Water Supply Water Supply RequirementsVacation or Extended Time Without Use Drain Pump Installation If Ice Maker Is Currently InstalledRear View Kit ContainsDrain Pump Installation Water Supply LineRear Panel Drain TubeVent Tube Drain Pump InstalledDrain Pump Mounting Tab Slot Drain Connection LevelingWater Filter Status Light Install the Water FilterWater Filtration System Using the Controls ICE Maker USEHow Your Ice Maker Works Replace the Water FilterNormal Sounds CleaningICE Maker Care Condenser Dirty or Clogged Condenser Interior ComponentsTo Shut Down the Ice Maker For Ice Makers with a Drain Pump InstalledVacation and Moving Care Ice Maker Seems Noisy TroubleshootingIce Maker Operation Produces No Ice Ice ProductionIce Maker Runs But If you need replacement parts U.S.ACanada Our Consultants Provide Assistance WithPerformance Data Sheet AccessoriesKitchenaid ICE Maker Warranty Three Year Limited Warranty Parts and LaborItems Excluded from Warranty Disclaimer of Representations Outside of WarrantyPage Seguridad DE LA Fábrica DE Hielo Su seguridad y la seguridad de los demás es muy importanteInstrucciones DE Instalación Desempaque la fábrica de hieloRequisitos de ubicación Requisitos eléctricosConexión del suministro de agua Requisitos del suministro de aguaVacaciones o tiempo prolongado sin uso El juego contiene Instalación de la bomba de desagüeVista posterior Si la fábrica de hielo ya está instalada Tapa de desagüeLínea de suministro de agua Instalación de la bomba de desagüeTubo de desagüe Ubicaciones de las piezasRanura de la lengüeta de montaje de la bomba de desagüe Bomba de desagüe instaladaConexión del desagüe Tubo de ventilaciónSistema de desagüe por gravedad Vista lateralConexión del desagüe NivelaciónSistema de la bomba de desagüe en algunos modelos Luz de estado del filtro de agua Sistema de filtración de aguaInstalación del filtro de agua USO DE LA Fábrica DE Hielo Cómo funciona su fábrica de hieloUso de los controles Reemplazo del filtro de aguaLimpieza Cuidado DE LA Fábrica DE HieloSonidos normales Condensador Un condensador sucio u obstruido Bandeja de agua Tapón de desagüeComponentes interiores Tornillo Espaciador de plástico Rejilla de corteCuidado durante las vacaciones y mudanzas Para apagar la fábrica de hieloSolución DE Problemas Funcionamiento de la fábrica de hieloLa fábrica de hielo no FuncionaProducción de hielo Calidad del hieloProblemas de plomería Ayuda O Servicio TécnicoEn los EE.UU Si necesita piezas de repuestoHoja DE Datos DEL Rendimiento AccesoriosFiltro de agua LimpiadorGarantía DE LA Fábrica DE Hielo DE Kitchenaid Exclusiones DE LA GarantíaEsta garantía limitada no cubre Exclusión DE Garantías ImplícitasPage Sécurité DE LA Machine À Glaçons Votre sécurité et celle des autres est très importanteInstructions D’INSTALLATION Exigences d’installationDéballage de la machine à glaçons Spécifications électriquesRaccordement à la canalisation d’eau Spécifications de l’alimentation en eauVacances ou longue période d’inutilisation Contenu de l’ensemble Installation de la pompe de vidangeVue arrière Si la machine à glaçons est installée Installation de la pompe de vidangeBouchon de vidange Canalisation d’alimentation en eauPompe de vidange installée Tube de vidangeRaccordement au conduit vidange Tube de ventilationSystème de vidange par gravité Vue latéraleRaccordement du conduit dévacuation NivellementSystème avec pompe de vidange sur certains modèles Témoin lumineux de l’état du filtre à eau Installer le filtre à eauSystème de filtration d’eau Utilisation des commandes Remplacement du filtre à eauUtilisation DE LA Machine À Glaçons Fonctionnement de la machine à glaçonsNettoyage Entretien DE LA Machine À GlaçonsBruits normaux Condenseur Un condenseur sale ou obstrué Composants intérieurs Machine à glaçons avec pompe de vidange Précautions à prendre pour les vacances ou le déménagementArrêt de la machine à glaçons Dépannage Production de glaçons Qualité des glaçonsAssistance OU Service Problèmes de plomberieAux États-Unis Au CanadaAccessoires Feuille DE Données SUR LA PerformanceFiltre à eau NettoyantGarantie DE LA Machine À Glaçons Kitchenaid Garantie Limitée DE Trois ANS Pièces ET MAIN-D’ŒUVREÉléments Exclus DE LA Garantie La présente garantie limitée ne couvre pasW10515677C

W10515677C specifications

The KitchenAid W10515677C is a versatile and essential component for any home chef who prioritizes both quality and performance in their kitchen tools. This food processor attachment, designed for use with KitchenAid stand mixers, enhances the functionality of the mixer by providing a reliable and efficient method for food preparation.

One of the standout features of the W10515677C is its powerful chopping and slicing capability. With sharp stainless-steel blades, this attachment allows for precise and consistent cuts, whether you're dicing vegetables, grating cheese, or slicing meats. The adjustable slicing disc provides multiple thickness options, making it easy to achieve the desired texture for your ingredients.

The design of the W10515677C is user-friendly, featuring an easy-to-assemble construction that ensures quick setup and minimal hassle. Once attached to the stand mixer, it operates seamlessly, allowing users to focus on their culinary creativity without worrying about the intricacies of food prep.

Another significant characteristic of this attachment is its generous capacity. It can handle large quantities of ingredients, making it perfect for meal preps or when cooking for a crowd. This efficiency saves time and simplifies the cooking process, allowing you to enjoy more time with family and friends.

Safety is also a key consideration in the design of the W10515677C. The attachment features a safety latch that keeps it securely attached to the stand mixer during operation. Additionally, the component comes with a push tool that ensures your hands are kept safely away from the blades while processing food.

Cleaning and maintenance are made straightforward, as most parts of the W10515677C are dishwasher safe, facilitating an easy cleanup after use. This attachment exemplifies KitchenAid’s commitment to durability and quality, built to withstand frequent use in busy kitchens.

In summary, the KitchenAid W10515677C food processor attachment elevates the experience of cooking at home. With its sharp stainless-steel blades, adjustable slicing capabilities, ease of use, and safety features, it stands as a reliable ally in meal preparation. Expanding the capabilities of your KitchenAid stand mixer, this attachment is a practical investment for anyone looking to enhance their culinary skills.
Top Page Image Contents