Jenn-Air W10136129C Drain Connection, Gravity Drain System, Drain Pump System on some models

Page 7

Drain Connection

Gravity Drain System

Connect the ice maker drain to your drain in accordance with all state and local codes and ordinances. If the ice maker is provided with a gravity drain system, follow these guidelines when installing drain lines. This will help keep water from flowing back into the ice maker storage bin and potentially flowing onto the floor causing water damage.

Drain lines must have a minimum of ⁵⁄₈" (15.88 mm) inside diameter.

Drain lines must have a 1" drop per 48" (2.54 cm drop per 122 cm) of run or ¹⁄₄" drop per 12" (6.35 mm per 30.48 cm) of run and must not have low points where water can settle.

The floor drains must be large enough to accommodate drainage from all drains.

The ideal installation has a standpipe with a 1¹⁄₂" (3.81 cm) to 2" (5.08 cm) PVC drain reducer installed directly below the outlet of the drain tube as shown. You must maintain a

1" (2.54 cm) air gap between the drain hose and the standpipe.

It may be desirable to insulate the drain line thoroughly up to the drain inlet.

SIDE VIEW

A

B

1⁷⁄₈"

(4.8 cm)

1" (2.54 cm)

23"

 

C

(58.4 cm)

D

2" - 1¹⁄₂"

(5 cm - 3.8 cm)

A. Drain hose

B. 1" (2.54 cm) air gap C. PVC drain reducer

D. Center of drain should be 23" (58.4 cm) from front of door, with or without the ³⁄₄" (1.91 cm) panel on the door. The drain should also be centered from left to right (7⁵⁄₁₆" [18.56 cm] from either side of the ice maker).

Drain Pump System (on some models)

Connect the ice maker drain to your drain in accordance with the International Plumbing Code and any local codes and ordinances.

NOTE: If the drain hose becomes twisted and water cannot drain, your ice maker will not work.

Connecting the Drain

After ensuring that the drain system is adequate, follow these steps to properly place the ice maker:

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1.Plug ice maker into a grounded 3 prong outlet.

WARNING

Excessive Weight Hazard

Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

2.Style 1 - For gravity drain system, push the ice maker into position so that the ice maker drain tube is positioned over the PVC drain reducer. See “Gravity Drain System” earlier in this section. Style 2 - For drain pump system connect the drain pump outlet hose to the drain. See “Drain Pump System” earlier in this section.

3.Recheck the ice maker to be sure that it is level. See “Leveling.”

4.If it is required by your local sanitation code, seal the cabinet to the floor with an approved caulking compound after all water and electrical connections have been made.

7

Image 7
Contents W10136129C USE & Care GuideManual DE USO Y Cuidado Guide D’UTILISATION ET D’ENTRETIENÍndice Table of ContentsTable DES Matières Tools and Parts ICE Maker SafetyInstallation Instructions Custom Panel DimensionsRemoving Packaging Materials Cleaning Before UseLocation Requirements Unpack the Ice MakerWater Supply Requirements Electrical RequirementsLeveling Connect Water Supply Connecting the Water LineRear View Drain Pump System on some models Connecting the DrainDrain Connection Gravity Drain SystemIce Maker Door Install Custom Overlay PanelRemove Door Top Hinge Reverse HingesReverse Door Catch Replace DoorHow Your Ice Maker Works Using the ControlsICE Maker USE Normal SoundsICE Maker Care CleaningInterior Components To shut down the ice maker TroubleshootingVacation and Moving Care Ice Maker OperationIce Production Plumbing ProblemsIce Quality U.S.A Assistance or ServiceCanada Disclaimer of Implied Warranties Limitation of Remedies JENN-AIRICE Maker WarrantyONE Year Limited Warranty Items JENN-AIR will not PAY forHerramientas y piezas Dimensiones del panel hecho a la medidaSeguridad DE LA Fábrica DE Hielo Instrucciones DE InstalaciónCómo quitar los materiales de empaque Desempaque la fábrica de hieloRequisitos de ubicación Limpieza antes del usoRequisitos del suministro de agua Requisitos eléctricosNivelación Conexión de la tubería de agua Conexión del suministro de aguaVista Posterior Conexión del desagüe Conexión del desagüeSistema de desagüe por gravedad Sistema de la bomba de desagüe en algunos modelosPuerta de la fábrica de hielo Instale el panel de revestimiento hecho a La medidaSacar la puerta Bisagra inferior Invertir las bisagrasVolver a colocar la puerta Bisagra superiorCómo funciona su fábrica de hielo Sonidos normalesProceso de elaboración de hielo Uso de los controles Cuidado DE LA Fábrica DE HieloLimpieza Piezas interiores CondensadorUn condensador sucio u obstruido Para apagar la fábrica de hielo Cuidado durante las vacaciones y MudanzasFuncionamiento de la fábrica de hielo Solución DE ProblemasSu fábrica de hielo no funciona Calidad del hielo Producción de hieloEn Canadá Problemas de plomeríaAyuda O Servicio Técnico En los EE.UUExclusión DE Garantías Implícitas Limitación DE Recursos Garantía DE LA Fábrica DE Hielo DE JENN-AIRGarantía Limitada DE UN AÑO JENN-AIR no Pagará POR LOS Siguientes ArtículosOutillage et pièces Instructions D’INSTALLATIONDimensions du panneau personnalisé Sécurité DE LA Machine À GlaçonsEnlèvement des matériaux d’emballage Exigences demplacementDéballage de la machine à glaçons Nettoyage avant l’utilisationSpécifications de l’alimentation en eau Spécifications électriquesNivellement Raccordement du tuyau d’eau Raccordement à la canalisation d’eauVUE Latérale Raccordement au conduit dévacuationVidange par gravité VUE ArrièreSystème avec pompe de vidange sur certains modèles Installation du panneau décoratif PersonnaliséRaccordement du conduit dévacuation Inversion des charnières Réinstallation de la portePorte de la machine à glaçons Dépose de la porteCharnière inférieure Sons normauxInversion du loquet de porte Fonctionnement de la machine à glaçons Utilisation des commandesControl Lock verrouillage des commandes Utilisation DE LA Machine À GlaçonsSurfaces extérieures Service Clean/Reset nettoyage/réinitialisationEntretien DE LA Machine À Glaçons NettoyageComposants intérieurs CondenseurUn condenseur sale ou obstrué Arrêt de la machine à glaçons Précautions à prendre avant les vacances Ou un déménagementLa machine à glaçons semble bruyante DépannageProduction de glaçons La machine à glaçons ne fonctionne pasGoût, odeur ou couleur grise des glaçons Qualité des glaçonsProblèmes de plomberie La grille ne découpe pas les plaques de glaceAux États-Unis Assistance OU ServiceAu Canada Garantie Limitée DE UN AN Garantie DE LA Machine À Glaçons JENN-AIRJENN-AIR NE Prendra PAS EN Charge 2008 All rights reserved W10136129C