GE ZIF36N LH, ZIR36N LH, ZIF36N RH, ZIR36N RH ″ Side Panels Insert end, Trim, 23 5/16

Page 11

Custom Panel Dimensions

36″ Refrigerators, Freezers

Side Panel or Filler Options

(Not to scale)

Side panels must be used whenever the sides of the

refrigerator or freezer will be exposed.

CUSTOM

1/4″ Side Panels

Insert end of

side panel into trim. Use stick-on hook and loop fastener strips to secure the panel to the refrigerator.

Top View

23 9/16"	1/2″ to 3/4″ Side Panels	24 3/4"
23 9/16"	Leading Edge	24 3/4"
	Leading Edge
	Flush with Cabinet
	Front. The front or
	leading edge must be
	finished to match
	cabinetry.
	Top View

PANEL DIMENSIONS

84"

Trim

2 9/16"

Standard 4″ high toekick or trim to fit.

Height may vary depending on application.

23 5/16"

1/2″ to 3/4″ Side Panels

Recessed front edge.

84"

3 3/4"

Standard 4″ high toekick or trim to fit.

Height may vary depending on application.

Top View

84"

2 5/16"

Standard 4″ high toekick or trim to fit.

Height may vary depending on application.

Image 11

Contents Installation Instructions ING Contents36″ Refrigerators, Freezers Design InformationSide By Side Installation Freezer Refrigerator When Installed into a corner″ thick custom panels-Without trim kits Installation Between Base Wall CabinetsInstallation At End-of-Run Advance planning exterior appearance optionsDescriptions ModelsAvailable Trim kitClearances Custom Panel Dimensions35-1/16 Handles ″ Panel Cut panels to sizeUnified Custom Grille Panel 71-3/8 Thick Panel Custom Door Panel DimensionsDimension a 35 -1/16Custom Door Panel Dimensions Using Standard Trim 23 5/16 ″ Side Panels Insert endTrim Grounding the Refrigerator InstallationMaterials Required FlooringStep Remove Packaging Shut off the main water supply InstallStep Water Line″ to 3/4″ Side Panels Leading edge of side Step Install Side PanelsIllustration a Illustration BTo Sides LevelOr Freezer Step SecureCheck Install 1/4″Power Step Door panelsArrange Interior Adjust DoorTemperature Controls AlignmentPieces Grille Panel Frame AdjustmentZGC2 Trim Kit To change grille panel sizeTools and materials required Parts ListZKHR1 Trim Kit For 1/4 ″ Panels Support for Custom HandlesLocate handle position Door using at least 2 screwsReinstall original screws into the door extrusion ZKHR1 Trim Kit For 1/4″ Panels″ Custom Panels ZKTR36LH/ZKTR36RH Trim KitBack Side Custom Panel Install panelsPanel height Install Handles StepAdjust GrilleGrille panel Install four of the six larger undercut screws so thatTop of the screws are 1/16″ from the surface Before ZKHTR1 Trim Kit For 3/4″ PanelsTools and materials required Part ListAssemble Temporarily mount door panelLocate PositionMount assembled panel Tubular Stainless Steel Handles ZKHRSS1 Trim Kit For 1/4″ PanelsMeasure and mark 1/4″ below the top edge If you are installing handle onto a Stainless Steel PanelStep Match handle extrusions to handle On the back side of the panel-at the handle sideDecorator Step Install standoffs onto handlesStep Install handles and panels Raised Panel on 1/4″ Thick Backing Begin ZKHTRSS1 For 3/4″ PanelsKit Before youShould be tight against the handle Using the Allen wrench provided. The standoffMatch Handle To PanelUnified 3/4″ Custom Grille Panel Kit Step Install Spacer PadsZUG75 Trim Kit Step Level Both Products Roll Both Products into OpeningRefrigerator and freezer must be secured to prevent tipping Trim Strip Install CenterStep Remove Wire Fence and Switch Cover Unified Base Cover Step Install Grille Base Cover Remove Grille FrameRemoving side screws. Discard top piece, retain Step Install Soffit Vent Top Secure Custom Panel To SupportStep Adjust Door Alignment