GE ZIR36N RH, ZIR36N LH Step Install Grille Base Cover Remove Grille Frame, Unified Base Cover

Page 38

Step 7

Install

Grille Base

Cover

Step 8

Remove

Grille Frame

ZUG75 Trim Kit

Unified 3/4″ Custom Grille Panel Kit

Unified Base Cover	Place
	Trim Over
	Hinges

•Open doors fully.

•Install the double width grille base cover by slipping the notched ends over the hinges.

Install	Install
3 Screws	3 Screws

•Place wire fence over the grille base cover (textured side out). Drive original wire fence screws through the fence, the grille base cover and into the frame.

Remove	Remove
Screws	Screws

•Back out 2 screws on each side of the top case trim.

•The top piece is secured to the unit with a rubber dust gasket. Roll the trim upwards to access and remove end screws as shown. Remove and discard inside pieces.

•Slide assembly out of the rubber gasket.

Remove

Screws

Dust

Gasket

Image 38

Contents Installation Instructions Contents INGDesign Information 36″ Refrigerators, FreezersWhen Installed into a corner Side By Side Installation Freezer RefrigeratorAdvance planning exterior appearance options Installation Between Base Wall CabinetsInstallation At End-of-Run ″ thick custom panels-Without trim kitsTrim kit ModelsAvailable DescriptionsCustom Panel Dimensions Clearances″ Panel Cut panels to size 35-1/16 Handles35 -1/16 Custom Door Panel DimensionsDimension a Unified Custom Grille Panel 71-3/8 Thick PanelCustom Door Panel Dimensions Using Standard Trim 23 5/16 ″ Side Panels Insert endTrim Flooring InstallationMaterials Required Grounding the RefrigeratorStep Remove Packaging Water Line InstallStep Shut off the main water supplyIllustration B Step Install Side PanelsIllustration a ″ to 3/4″ Side Panels Leading edge of sideStep Secure LevelOr Freezer To SidesDoor panels Install 1/4″Power Step CheckAlignment Adjust DoorTemperature Controls Arrange InteriorTo change grille panel size Grille Panel Frame AdjustmentZGC2 Trim Kit PiecesSupport for Custom Handles Parts ListZKHR1 Trim Kit For 1/4 ″ Panels Tools and materials requiredZKHR1 Trim Kit For 1/4″ Panels Door using at least 2 screwsReinstall original screws into the door extrusion Locate handle positionZKTR36LH/ZKTR36RH Trim Kit ″ Custom PanelsInstall panels Back Side Custom PanelGrille Install Handles StepAdjust Panel heightGrille panel Install four of the six larger undercut screws so thatTop of the screws are 1/16″ from the surface Part List ZKHTR1 Trim Kit For 3/4″ PanelsTools and materials required BeforePosition Temporarily mount door panelLocate AssembleMount assembled panel ZKHRSS1 Trim Kit For 1/4″ Panels Tubular Stainless Steel HandlesOn the back side of the panel-at the handle side If you are installing handle onto a Stainless Steel PanelStep Match handle extrusions to handle Measure and mark 1/4″ below the top edgeDecorator Step Install standoffs onto handlesStep Install handles and panels Raised Panel on 1/4″ Thick Backing Before you ZKHTRSS1 For 3/4″ PanelsKit BeginTo Panel Using the Allen wrench provided. The standoffMatch Handle Should be tight against the handleUnified 3/4″ Custom Grille Panel Kit Step Install Spacer PadsZUG75 Trim Kit Step Level Both Products Roll Both Products into OpeningRefrigerator and freezer must be secured to prevent tipping Trim Strip Install CenterStep Remove Wire Fence and Switch Cover Step Install Grille Base Cover Remove Grille Frame Unified Base CoverStep Install Soffit Vent Top Secure Custom Panel To Support Removing side screws. Discard top piece, retainStep Adjust Door Alignment