GE ZIR36N LH, ZIF36N RH, ZIR36N RH, ZIF36N LH Install Handles Step, Adjust, Grille, Panel height

Page 24

ZKTR36LH/ZKTR36RH Trim Kit

3/4″ Custom Panels

Step 5

• Install new door handle using original screws.

Install

 

handles

 

Step 6

• For shipping purposes, the top case trim is secured

 

Adjust

at the 84″ installation height.

Screws

grille

• Loosen 2 screws on both sides of the case trim

panel height

and raise or lower trim to meet soffit height, from

 

 

83-1/2″to 84-1/2″.

 

• Tighten all 4 screws.

Top Case Trim

IMPORTANT: Maintain 1-1/2″min. gap between top of

 

door and bottom of grille panel.

Raise To

 

Installation

 

Height

Step 7

• Secure the grille panel support to the back side of

Secure 3/4″

the 3/4″ custom panel with #6 screws.

panel to

• Be sure the lip of the support is over the top of the

grille panel

wood panel.

support

 

 

Panel Support

 

Overlaps Top

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Installation Instructions Contents INGDesign Information 36″ Refrigerators, FreezersWhen Installed into a corner Side By Side Installation Freezer RefrigeratorInstallation Between Base Wall Cabinets Installation At End-of-RunAdvance planning exterior appearance options ″ thick custom panels-Without trim kitsModels AvailableTrim kit DescriptionsCustom Panel Dimensions Clearances″ Panel Cut panels to size 35-1/16 HandlesCustom Door Panel Dimensions Dimension a35 -1/16 Unified Custom Grille Panel 71-3/8 Thick PanelCustom Door Panel Dimensions Using Standard Trim ″ Side Panels Insert end Trim23 5/16 Installation Materials RequiredFlooring Grounding the RefrigeratorStep Remove Packaging Install StepWater Line Shut off the main water supplyStep Install Side Panels Illustration aIllustration B ″ to 3/4″ Side Panels Leading edge of sideLevel Or FreezerStep Secure To SidesInstall 1/4″ Power StepDoor panels CheckAdjust Door Temperature ControlsAlignment Arrange InteriorGrille Panel Frame Adjustment ZGC2 Trim KitTo change grille panel size PiecesParts List ZKHR1 Trim Kit For 1/4 ″ PanelsSupport for Custom Handles Tools and materials requiredDoor using at least 2 screws Reinstall original screws into the door extrusionZKHR1 Trim Kit For 1/4″ Panels Locate handle positionZKTR36LH/ZKTR36RH Trim Kit ″ Custom PanelsInstall panels Back Side Custom PanelInstall Handles Step AdjustGrille Panel heightInstall four of the six larger undercut screws so that Top of the screws are 1/16″ from the surfaceGrille panel ZKHTR1 Trim Kit For 3/4″ Panels Tools and materials requiredPart List BeforeTemporarily mount door panel LocatePosition AssembleMount assembled panel ZKHRSS1 Trim Kit For 1/4″ Panels Tubular Stainless Steel HandlesIf you are installing handle onto a Stainless Steel Panel Step Match handle extrusions to handleOn the back side of the panel-at the handle side Measure and mark 1/4″ below the top edgeStep Install standoffs onto handles Step Install handles and panelsDecorator Raised Panel on 1/4″ Thick Backing ZKHTRSS1 For 3/4″ Panels KitBefore you BeginUsing the Allen wrench provided. The standoff Match HandleTo Panel Should be tight against the handleStep Install Spacer Pads ZUG75 Trim KitUnified 3/4″ Custom Grille Panel Kit Roll Both Products into Opening Refrigerator and freezer must be secured to prevent tippingStep Level Both Products Install Center Step Remove Wire Fence and Switch CoverTrim Strip Step Install Grille Base Cover Remove Grille Frame Unified Base CoverStep Install Soffit Vent Top Secure Custom Panel To Support Removing side screws. Discard top piece, retainStep Adjust Door Alignment
Top Page Image Contents