GE ZIF36N RH, ZIR36N LH, ZIR36N RH, ZIF36N LH Custom Door Panel Dimensions, 35 -1/16, Dimension a

Page 9

Custom Panel Dimensions

36″ Refrigerators, Freezers

Custom Door Panel Dimensions

Using Trim Kits ZKTR36LH or ZKTR36RH 3/4″ thick panel with kit supplied handle

35 -1/16"

ZIR36N Refrigerator

ZIF36N Freezer

•The ZKTR36LH (or ZKTR36RH) trim kit provides for the installation of 3/4″ thick custom door and grille panels, using the supplied handle. Cut panel to size and install.

IMPORTANT: Maximum door panel weight is 67 lbs., maximum grille panel weight is 9 lbs.

3/4" Thick

Custom Panel

68-15/16"

A

Custom Grille Panel

35 1/4"

3/4" Thick Panel

Grille Panel height can vary to fill installation height.

Installation Height

Dimension A

83-1/2″

7-3/4″

84″

8-1/4″

84-1/2″

8-3/4″

 

 

IMPORTANT: Maintain 1-1/2″min. gap between top of door and bottom of grille panel.

Unified Custom Grille Panel

71-3/8"

A

3/4" Thick Panel

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Installation Instructions ING Contents36″ Refrigerators, Freezers Design InformationSide By Side Installation Freezer Refrigerator When Installed into a cornerInstallation At End-of-Run Installation Between Base Wall CabinetsAdvance planning exterior appearance options ″ thick custom panels-Without trim kitsAvailable ModelsTrim kit DescriptionsClearances Custom Panel Dimensions35-1/16 Handles ″ Panel Cut panels to sizeDimension a Custom Door Panel Dimensions35 -1/16 Unified Custom Grille Panel 71-3/8 Thick PanelCustom Door Panel Dimensions Using Standard Trim ″ Side Panels Insert end Trim23 5/16 Materials Required InstallationFlooring Grounding the RefrigeratorStep Remove Packaging Step InstallWater Line Shut off the main water supplyIllustration a Step Install Side PanelsIllustration B ″ to 3/4″ Side Panels Leading edge of sideOr Freezer LevelStep Secure To SidesPower Step Install 1/4″Door panels CheckTemperature Controls Adjust DoorAlignment Arrange InteriorZGC2 Trim Kit Grille Panel Frame AdjustmentTo change grille panel size PiecesZKHR1 Trim Kit For 1/4 ″ Panels Parts ListSupport for Custom Handles Tools and materials requiredReinstall original screws into the door extrusion Door using at least 2 screwsZKHR1 Trim Kit For 1/4″ Panels Locate handle position″ Custom Panels ZKTR36LH/ZKTR36RH Trim KitBack Side Custom Panel Install panelsAdjust Install Handles StepGrille Panel heightInstall four of the six larger undercut screws so that Top of the screws are 1/16″ from the surfaceGrille panel Tools and materials required ZKHTR1 Trim Kit For 3/4″ PanelsPart List BeforeLocate Temporarily mount door panelPosition AssembleMount assembled panel Tubular Stainless Steel Handles ZKHRSS1 Trim Kit For 1/4″ PanelsStep Match handle extrusions to handle If you are installing handle onto a Stainless Steel PanelOn the back side of the panel-at the handle side Measure and mark 1/4″ below the top edgeStep Install standoffs onto handles Step Install handles and panelsDecorator Raised Panel on 1/4″ Thick Backing Kit ZKHTRSS1 For 3/4″ PanelsBefore you BeginMatch Handle Using the Allen wrench provided. The standoffTo Panel Should be tight against the handleStep Install Spacer Pads ZUG75 Trim KitUnified 3/4″ Custom Grille Panel Kit Roll Both Products into Opening Refrigerator and freezer must be secured to prevent tippingStep Level Both Products Install Center Step Remove Wire Fence and Switch CoverTrim Strip Unified Base Cover Step Install Grille Base Cover Remove Grille FrameRemoving side screws. Discard top piece, retain Step Install Soffit Vent Top Secure Custom Panel To SupportStep Adjust Door Alignment
Top Page Image Contents