GE ZIF36N RH, ZIR36N LH, ZIR36N RH, ZIF36N LH ZKHTRSS1 For 3/4″ Panels, Kit, Before you, Begin

Page 33

ZKHTRSS1 (For 3/4″ Panels)

Tubular Stainless Steel Handles

Kit	Right hand door swing models are illustrated in these
Contents	instructions. Follow these instructions for left hand
	models.

This kit provides for the installation of a Tubular Stainless Steel handle on a 3/4″ thick decorator door panel. The door extrusions allow the custom handle to be secured to the door structure, rather than to the custom panel.

•Select the extrusion for your model, discard other extrusion.

Tools and materials required:

•#2 Phillips screwdriver

•Drill and 1/8″, 9/32″ bits

•Custom door panel

•Safety glasses

•Center punch

•Masking tape

•Hammer

•Pencil

Parts List:

A. Handle extrusion (for left hand models) B. Handle extrusion (for right hand models) C. Stainless tubular handle

D. 4 Handle standoffs

E. 6 Screws for handle standoffs (4 required, 2 extra)

F. 6 Set screws (4 required, 2 extra) G. 3/32″ Allen wrench for set screws

This kit must be used in combination with ZKTR36RH or ZKTR36LH trim kit.

NOTE: It is best that 2 people install this kit.

A

B

C

D

E

F

G

Before you	• The 3/4″ custom panel must be routed to
begin:	accommodate the handle extrusion. Rout the panel
	as illustrated, 1/4″ deep, and 1-13/16″wide, top to
	bottom on the handle side.
	• Follow the instructions in the ZKTR36RH
	(or ZKTR36LH) to install trim onto the door.
	Discard the handle supplied with that kit.
	• Continue the instructions in the ZKTR36RH
	(or ZKTR36LH) trim kit to install support brackets
	to the bottom of the panel.

Custom Panel

1-13/16"

1/4" Max.

Back Side

Handle Side

IMPORTANT: Optional final appearance depends on careful routing depth. Do not exceed 1/4″ routing depth.

33

Image 33

Contents Installation Instructions ING Contents36″ Refrigerators, Freezers Design InformationSide By Side Installation Freezer Refrigerator When Installed into a cornerInstallation At End-of-Run Installation Between Base Wall CabinetsAdvance planning exterior appearance options ″ thick custom panels-Without trim kitsAvailable ModelsTrim kit DescriptionsClearances Custom Panel Dimensions35-1/16 Handles ″ Panel Cut panels to sizeDimension a Custom Door Panel Dimensions35 -1/16 Unified Custom Grille Panel 71-3/8 Thick PanelCustom Door Panel Dimensions Using Standard Trim ″ Side Panels Insert end Trim23 5/16 Materials Required InstallationFlooring Grounding the RefrigeratorStep Remove Packaging Step InstallWater Line Shut off the main water supplyIllustration a Step Install Side PanelsIllustration B ″ to 3/4″ Side Panels Leading edge of sideOr Freezer LevelStep Secure To SidesPower Step Install 1/4″Door panels CheckTemperature Controls Adjust DoorAlignment Arrange InteriorZGC2 Trim Kit Grille Panel Frame AdjustmentTo change grille panel size PiecesZKHR1 Trim Kit For 1/4 ″ Panels Parts ListSupport for Custom Handles Tools and materials requiredReinstall original screws into the door extrusion Door using at least 2 screwsZKHR1 Trim Kit For 1/4″ Panels Locate handle position″ Custom Panels ZKTR36LH/ZKTR36RH Trim KitBack Side Custom Panel Install panelsAdjust Install Handles StepGrille Panel heightInstall four of the six larger undercut screws so that Top of the screws are 1/16″ from the surfaceGrille panel Tools and materials required ZKHTR1 Trim Kit For 3/4″ PanelsPart List BeforeLocate Temporarily mount door panelPosition AssembleMount assembled panel Tubular Stainless Steel Handles ZKHRSS1 Trim Kit For 1/4″ PanelsStep Match handle extrusions to handle If you are installing handle onto a Stainless Steel PanelOn the back side of the panel-at the handle side Measure and mark 1/4″ below the top edgeStep Install standoffs onto handles Step Install handles and panelsDecorator Raised Panel on 1/4″ Thick Backing Kit ZKHTRSS1 For 3/4″ PanelsBefore you BeginMatch Handle Using the Allen wrench provided. The standoffTo Panel Should be tight against the handleStep Install Spacer Pads ZUG75 Trim KitUnified 3/4″ Custom Grille Panel Kit Roll Both Products into Opening Refrigerator and freezer must be secured to prevent tippingStep Level Both Products Install Center Step Remove Wire Fence and Switch CoverTrim Strip Unified Base Cover Step Install Grille Base Cover Remove Grille FrameRemoving side screws. Discard top piece, retain Step Install Soffit Vent Top Secure Custom Panel To SupportStep Adjust Door Alignment