GE ZIR36N LH, ZIF36N RH, ZIR36N RH, ZIF36N LH Step Adjust Door Alignment, Bushing

Page 40

Step 11

Adjust

Door

Alignment

ZUG75 Trim Kit

Unified 3/4″ Custom Grille Panel Kit

Bushing

Door Hinge

Case Hinge

Raise

Pin Shoulder

5/16" Wrench

Check door alignment. The top of the door should be parallel with the grille panel. If the door appears to be too high or too low on the handle side, adjustments can be made.

•Use a 5/16″ wrench to turn the hinge.

•To raise the door, turn adjustable hinge pin towards the right.

•To lower the door, turn hinge pin towards the left.

NOTE: While performing installations described in this book, safety glasses or goggles should be worn.

For Monogram® local service in your area, call 1.800.444.1845.

NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice.

Pub. No. 49-60055-4

Dwg. No. 197D2785P001

GE Consumer & Industrial

Appliances

General Electric Company Louisville, KY 40225 ge.com

08-07 JR

Image 40

Contents Installation Instructions Contents INGDesign Information 36″ Refrigerators, FreezersWhen Installed into a corner Side By Side Installation Freezer RefrigeratorInstallation Between Base Wall Cabinets Installation At End-of-RunAdvance planning exterior appearance options ″ thick custom panels-Without trim kitsModels AvailableTrim kit DescriptionsCustom Panel Dimensions Clearances″ Panel Cut panels to size 35-1/16 HandlesCustom Door Panel Dimensions Dimension a35 -1/16 Unified Custom Grille Panel 71-3/8 Thick PanelCustom Door Panel Dimensions Using Standard Trim Trim ″ Side Panels Insert end23 5/16 Installation Materials RequiredFlooring Grounding the RefrigeratorStep Remove Packaging Install StepWater Line Shut off the main water supplyStep Install Side Panels Illustration aIllustration B ″ to 3/4″ Side Panels Leading edge of sideLevel Or FreezerStep Secure To SidesInstall 1/4″ Power StepDoor panels CheckAdjust Door Temperature ControlsAlignment Arrange InteriorGrille Panel Frame Adjustment ZGC2 Trim KitTo change grille panel size PiecesParts List ZKHR1 Trim Kit For 1/4 ″ PanelsSupport for Custom Handles Tools and materials requiredDoor using at least 2 screws Reinstall original screws into the door extrusionZKHR1 Trim Kit For 1/4″ Panels Locate handle positionZKTR36LH/ZKTR36RH Trim Kit ″ Custom PanelsInstall panels Back Side Custom PanelInstall Handles Step AdjustGrille Panel heightTop of the screws are 1/16″ from the surface Install four of the six larger undercut screws so thatGrille panel ZKHTR1 Trim Kit For 3/4″ Panels Tools and materials requiredPart List BeforeTemporarily mount door panel LocatePosition AssembleMount assembled panel ZKHRSS1 Trim Kit For 1/4″ Panels Tubular Stainless Steel HandlesIf you are installing handle onto a Stainless Steel Panel Step Match handle extrusions to handleOn the back side of the panel-at the handle side Measure and mark 1/4″ below the top edgeStep Install handles and panels Step Install standoffs onto handlesDecorator Raised Panel on 1/4″ Thick Backing ZKHTRSS1 For 3/4″ Panels KitBefore you BeginUsing the Allen wrench provided. The standoff Match HandleTo Panel Should be tight against the handleZUG75 Trim Kit Step Install Spacer PadsUnified 3/4″ Custom Grille Panel Kit Refrigerator and freezer must be secured to prevent tipping Roll Both Products into OpeningStep Level Both Products Step Remove Wire Fence and Switch Cover Install CenterTrim Strip Step Install Grille Base Cover Remove Grille Frame Unified Base CoverStep Install Soffit Vent Top Secure Custom Panel To Support Removing side screws. Discard top piece, retainStep Adjust Door Alignment