GE ZIR36N RH Adjust Door, Alignment, Arrange Interior, Set, Temperature Controls, Start, Icemaker

Page 18

Installation

36″ Refrigerators, Freezers

Step 11	Check door alignment. The top of the door should
Adjust Door	be parallel with the grille panel. If the door appears
Alignment	to be too high or too low on the handle side,
	adjustments can be made by turning the hinge.
	• To raise the door, turn adjustable hinge pin
	towards the right.
	• To lower the door, turn hinge pin towards the left.
	Turn the hinge pin with a 5/16″ wrench or, on some
	models, use the 3/16″ Allen wrench taped to the
	hinge.

Step 12	• Remove internal packing materials.
Arrange Interior	• Remove tape from all shelves.
and Set	• Set control at “5”.
Temperature
Controls	IMPORTANT: Allow 24 hours for temperatures to
	stabilize before making adjustments.
Step 13	• Start the switch to I (on). The green light will come
Start	on and the icemaker will begin operation
Icemaker	automatically.
	• Be sure nothing interferes with the sweep of the
	feeler arm.
	• Discard the first few batches of ice cubes.
	• To turn the icemaker off, set the switch to O (off).
	Allow 45 minutes for the icemaker to resume
	operation.

Door Should be Parallel

With Grille Panel

Bushing

Door Hinge

Case Hinge

Raise

Pin Shoulder

5/16" Wrench

Power Switch

Feeler Arm

Green Power Light

Step 14	• A standard toekick is supplied. Install with 2 screws
Install	provided, adjust to desired height and tighten
Toekick	screws.
	IMPORTANT: The vented toekick must remain
	unobstructed for proper air circulation and operation.

18

Image 18

Contents Installation Instructions Contents INGDesign Information 36″ Refrigerators, FreezersWhen Installed into a corner Side By Side Installation Freezer RefrigeratorAdvance planning exterior appearance options Installation Between Base Wall CabinetsInstallation At End-of-Run ″ thick custom panels-Without trim kitsTrim kit ModelsAvailable DescriptionsCustom Panel Dimensions Clearances″ Panel Cut panels to size 35-1/16 Handles35 -1/16 Custom Door Panel DimensionsDimension a Unified Custom Grille Panel 71-3/8 Thick PanelCustom Door Panel Dimensions Using Standard Trim ″ Side Panels Insert end Trim23 5/16 Flooring InstallationMaterials Required Grounding the RefrigeratorStep Remove Packaging Water Line InstallStep Shut off the main water supplyIllustration B Step Install Side PanelsIllustration a ″ to 3/4″ Side Panels Leading edge of sideStep Secure LevelOr Freezer To SidesDoor panels Install 1/4″Power Step CheckAlignment Adjust DoorTemperature Controls Arrange InteriorTo change grille panel size Grille Panel Frame AdjustmentZGC2 Trim Kit PiecesSupport for Custom Handles Parts ListZKHR1 Trim Kit For 1/4 ″ Panels Tools and materials requiredZKHR1 Trim Kit For 1/4″ Panels Door using at least 2 screwsReinstall original screws into the door extrusion Locate handle positionZKTR36LH/ZKTR36RH Trim Kit ″ Custom PanelsInstall panels Back Side Custom PanelGrille Install Handles StepAdjust Panel heightInstall four of the six larger undercut screws so that Top of the screws are 1/16″ from the surfaceGrille panel Part List ZKHTR1 Trim Kit For 3/4″ PanelsTools and materials required BeforePosition Temporarily mount door panelLocate AssembleMount assembled panel ZKHRSS1 Trim Kit For 1/4″ Panels Tubular Stainless Steel HandlesOn the back side of the panel-at the handle side If you are installing handle onto a Stainless Steel PanelStep Match handle extrusions to handle Measure and mark 1/4″ below the top edgeStep Install standoffs onto handles Step Install handles and panelsDecorator Raised Panel on 1/4″ Thick Backing Before you ZKHTRSS1 For 3/4″ PanelsKit BeginTo Panel Using the Allen wrench provided. The standoffMatch Handle Should be tight against the handleStep Install Spacer Pads ZUG75 Trim KitUnified 3/4″ Custom Grille Panel Kit Roll Both Products into Opening Refrigerator and freezer must be secured to prevent tippingStep Level Both Products Install Center Step Remove Wire Fence and Switch CoverTrim Strip Step Install Grille Base Cover Remove Grille Frame Unified Base CoverStep Install Soffit Vent Top Secure Custom Panel To Support Removing side screws. Discard top piece, retainStep Adjust Door Alignment