GE ZIR36N RH, ZIR36N LH, ZIF36N RH, ZIF36N LH Custom Door Panel Dimensions Using Standard Trim

Page 10

Custom Panel Dimensions

36″ Refrigerators, Freezers

Custom Door Panel Dimensions Using Standard Trim

Using Trim Kit ZKTR36LH or ZKTR36RH 3/4″ thick panel with custom handle

35 1/4 "

3/4" Thick

Custom Panel

With Custom

Handle

68-15/16"

Custom Grille Panel

35 1/4"

A	3/4" Thick Panel

Grille Panel height can vary to fill installation height.

Installation Height	Dimension A
83-1/2″	7-3/4″
84″	8-1/4″
84-1/2″	8-3/4″

IMPORTANT: Maintain 1-1/2″min. gap between top of door and bottom of grille panel.

Unified Custom Grille Panel

71-3/8"

ZIR36N Refrigerator

ZIF36N Freezer

•The ZKTR36LH (or ZKTR36RH) trim kit installed together with a ZKHTR1 custom handle kit provides for the installation of 3/4″ thick custom door and grille panels with a custom handle of your choice. Order ZKHTRSS1 for a tubular stainless steel handle. Cut panels to size, rout the handle side of the panel as shown below and install.

IMPORTANT: Maximum door panel weight is 67 lbs., maximum grille panel weight is 9 lbs.

Rout back side of panel as shown

on the handle side 1-13/16"

1/4"
max	Appearance Side

A

3/4" Thick Panel

10

Image 10

Contents Installation Instructions Contents INGDesign Information 36″ Refrigerators, FreezersWhen Installed into a corner Side By Side Installation Freezer RefrigeratorAdvance planning exterior appearance options Installation Between Base Wall CabinetsInstallation At End-of-Run ″ thick custom panels-Without trim kitsTrim kit ModelsAvailable DescriptionsCustom Panel Dimensions Clearances″ Panel Cut panels to size 35-1/16 Handles35 -1/16 Custom Door Panel DimensionsDimension a Unified Custom Grille Panel 71-3/8 Thick PanelCustom Door Panel Dimensions Using Standard Trim Trim ″ Side Panels Insert end23 5/16 Flooring InstallationMaterials Required Grounding the RefrigeratorStep Remove Packaging Water Line InstallStep Shut off the main water supplyIllustration B Step Install Side PanelsIllustration a ″ to 3/4″ Side Panels Leading edge of sideStep Secure LevelOr Freezer To SidesDoor panels Install 1/4″Power Step CheckAlignment Adjust DoorTemperature Controls Arrange InteriorTo change grille panel size Grille Panel Frame AdjustmentZGC2 Trim Kit PiecesSupport for Custom Handles Parts ListZKHR1 Trim Kit For 1/4 ″ Panels Tools and materials requiredZKHR1 Trim Kit For 1/4″ Panels Door using at least 2 screwsReinstall original screws into the door extrusion Locate handle positionZKTR36LH/ZKTR36RH Trim Kit ″ Custom PanelsInstall panels Back Side Custom PanelGrille Install Handles StepAdjust Panel heightTop of the screws are 1/16″ from the surface Install four of the six larger undercut screws so thatGrille panel Part List ZKHTR1 Trim Kit For 3/4″ PanelsTools and materials required BeforePosition Temporarily mount door panelLocate AssembleMount assembled panel ZKHRSS1 Trim Kit For 1/4″ Panels Tubular Stainless Steel HandlesOn the back side of the panel-at the handle side If you are installing handle onto a Stainless Steel PanelStep Match handle extrusions to handle Measure and mark 1/4″ below the top edgeStep Install handles and panels Step Install standoffs onto handlesDecorator Raised Panel on 1/4″ Thick Backing Before you ZKHTRSS1 For 3/4″ PanelsKit BeginTo Panel Using the Allen wrench provided. The standoffMatch Handle Should be tight against the handleZUG75 Trim Kit Step Install Spacer PadsUnified 3/4″ Custom Grille Panel Kit Refrigerator and freezer must be secured to prevent tipping Roll Both Products into OpeningStep Level Both Products Step Remove Wire Fence and Switch Cover Install CenterTrim Strip Step Install Grille Base Cover Remove Grille Frame Unified Base CoverStep Install Soffit Vent Top Secure Custom Panel To Support Removing side screws. Discard top piece, retainStep Adjust Door Alignment