GE ZIF36N LH ZGC2 Trim Kit, Grille Panel Frame Adjustment, To change grille panel size, Pieces

Page 19

ZGC2 Trim Kit

Grille Panel Frame Adjustment

This kit provides optional side trim pieces for the original grille panel frame to fit 83-1/2″and 84-1/2″installation heights.

To change grille panel size:

•Determine the installation height by measuring the enclosure from the floor to the underside of soffit. When there is no soffit, measure to the top of the adjacent cabinets.

•Adjust refrigerator case trim to desired height. See Product Installation.

•Select the side trim pieces for your installation height.

A. Locate original grille panel frame supplied with the refrigerator.

•Remove 8 screws (two on each corner) and “L” brackets as illustrated.

B. Select correct set of side trim pieces (2 sets provided).

• Secure new side trim pieces to original bottom trim.

E. Mount the assembled panel by dropping into slots on the case trim.

1-1/2" min. gap

	Barrel	Discard
	Nuts	Discard
	Nuts	Side Trim
		Side Trim
		Pieces

C. Remove barrel nuts from original side trim pieces (2 each side).

•Reinstall the barrel nuts on the new side trim pieces you have selected. Discard original side trim.

IMPORTANT: Maintain 1-1/2″min. gap between top of door and bottom of grille panel.

D. Slide custom panel into front slots.

•Secure the top trim piece to the frame with “L” brackets and screws.

19

Image 19

Contents Installation Instructions ING Contents36″ Refrigerators, Freezers Design InformationSide By Side Installation Freezer Refrigerator When Installed into a corner″ thick custom panels-Without trim kits Installation Between Base Wall CabinetsInstallation At End-of-Run Advance planning exterior appearance optionsDescriptions ModelsAvailable Trim kitClearances Custom Panel Dimensions35-1/16 Handles ″ Panel Cut panels to sizeUnified Custom Grille Panel 71-3/8 Thick Panel Custom Door Panel DimensionsDimension a 35 -1/16Custom Door Panel Dimensions Using Standard Trim Trim ″ Side Panels Insert end23 5/16 Grounding the Refrigerator InstallationMaterials Required FlooringStep Remove Packaging Shut off the main water supply InstallStep Water Line″ to 3/4″ Side Panels Leading edge of side Step Install Side PanelsIllustration a Illustration BTo Sides LevelOr Freezer Step SecureCheck Install 1/4″Power Step Door panelsArrange Interior Adjust DoorTemperature Controls AlignmentPieces Grille Panel Frame AdjustmentZGC2 Trim Kit To change grille panel sizeTools and materials required Parts ListZKHR1 Trim Kit For 1/4 ″ Panels Support for Custom HandlesLocate handle position Door using at least 2 screwsReinstall original screws into the door extrusion ZKHR1 Trim Kit For 1/4″ Panels″ Custom Panels ZKTR36LH/ZKTR36RH Trim KitBack Side Custom Panel Install panelsPanel height Install Handles StepAdjust GrilleTop of the screws are 1/16″ from the surface Install four of the six larger undercut screws so thatGrille panel Before ZKHTR1 Trim Kit For 3/4″ PanelsTools and materials required Part ListAssemble Temporarily mount door panelLocate PositionMount assembled panel Tubular Stainless Steel Handles ZKHRSS1 Trim Kit For 1/4″ PanelsMeasure and mark 1/4″ below the top edge If you are installing handle onto a Stainless Steel PanelStep Match handle extrusions to handle On the back side of the panel-at the handle sideStep Install handles and panels Step Install standoffs onto handlesDecorator Raised Panel on 1/4″ Thick Backing Begin ZKHTRSS1 For 3/4″ PanelsKit Before youShould be tight against the handle Using the Allen wrench provided. The standoffMatch Handle To PanelZUG75 Trim Kit Step Install Spacer PadsUnified 3/4″ Custom Grille Panel Kit Refrigerator and freezer must be secured to prevent tipping Roll Both Products into OpeningStep Level Both Products Step Remove Wire Fence and Switch Cover Install CenterTrim Strip Unified Base Cover Step Install Grille Base Cover Remove Grille FrameRemoving side screws. Discard top piece, retain Step Install Soffit Vent Top Secure Custom Panel To SupportStep Adjust Door Alignment