GE ZIR36N LH, ZIF36N RH, ZIR36N RH, ZIF36N LH Raised Panel on 1/4″ Thick Backing

Page 32

Step 4A

Install handles and panels

FOR

STAINLESS

STEEL

PANELS

ZKHRSS1 Trim Kit (For 1/4″ Panels)

Tubular Stainless Steel Handles

 

 

 

 

 

 

 

 

 

 

 

 

Screw

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Extrusion

 

 

 

 

 

 

Corrugated

Spacer

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ring

 

 

 

 

 

 

 

Stainless

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Panel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Handle

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Slide panel into the door trim. Leave about 4″

 

 

 

 

 

 

 

 

• Crimp top and bottom edges of corrugated.

• Slide corrugated into door trim. Leave about 1/4″

 

of the panel exposed to allow room to install

gap between edge of corrugated and hinge side

 

the handle extrusion.

 

trim of the door.

• Place a spacer ring over each screw hole on the

 

 

 

 

 

 

 

 

 

extrusion. Use tape to hold in place.

NOTE: Panels have a protective plastic covering. Peel

• Place extrusion onto panel. Use a pencil to punch

away just enough to allow panel to slide into trim and to

 

hole in tape covering spacer rings and align with

clear handle mounting screws. The plastic covering will

 

screw holes.

 

keep the panel clean during the installation process.

• Install mounting screws through the extrusion and

Be sure to maintain 1/4″ gap between corrugated

 

panel.

 

 

 

 

 

 

 

• Drive screw part way through the top standoff,

and hinge side trim.

 

then part way through the bottom standoff. Install

 

 

 

 

 

 

 

 

 

remaining standoffs part way.

 

 

 

 

 

 

 

 

 

• Drive screws until the handles are tight against

the panel.

• Slide the assembly into the door trim until the extrusion fits firmly against the steel door.

• Reinstall original screws into the door extrusion.

Raised Panel on 1/4″ Thick Backing:

A raised panel design secured to a 1/4″ thick backing (screwed or glued) can be used with this handle kit.

•Cut the 1/4″ thick panels to size.

•Fabricate the raised panel to allow 1-1/4″clearance from the hinge side of the panel to avoid striking adjacent cabinetry.

•Allow 5/16″ clearance at the other edges to allow for the trim flange.

•Total panel thickness should not exceed 3/4″.

•Countertops adjacent to the refrigerator installation should be mitered 45°.

NOTE: Longer Screws, obtained locally, will be required

 

Raised Panel on 1/4" Thick Backing

1/4"

Appearance

5/16" Clearance

 

Thick

Panel

Custom Panel

Backing

 

5/16"

1-1/4"

Clearance

Clearance

handle Side

hinge side

 

 

5/16" Clearance

to accommodate panel thickness. Use stainless steel

5/16" Clearance

#10-32x1-1/4″truss Phillips head screws.

 

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Installation Instructions Contents INGDesign Information 36″ Refrigerators, FreezersWhen Installed into a corner Side By Side Installation Freezer RefrigeratorInstallation Between Base Wall Cabinets Installation At End-of-RunAdvance planning exterior appearance options ″ thick custom panels-Without trim kitsModels AvailableTrim kit DescriptionsCustom Panel Dimensions Clearances″ Panel Cut panels to size 35-1/16 HandlesCustom Door Panel Dimensions Dimension a35 -1/16 Unified Custom Grille Panel 71-3/8 Thick PanelCustom Door Panel Dimensions Using Standard Trim 23 5/16 ″ Side Panels Insert endTrim Installation Materials RequiredFlooring Grounding the RefrigeratorStep Remove Packaging Install StepWater Line Shut off the main water supplyStep Install Side Panels Illustration aIllustration B ″ to 3/4″ Side Panels Leading edge of sideLevel Or FreezerStep Secure To SidesInstall 1/4″ Power StepDoor panels CheckAdjust Door Temperature ControlsAlignment Arrange InteriorGrille Panel Frame Adjustment ZGC2 Trim KitTo change grille panel size PiecesParts List ZKHR1 Trim Kit For 1/4 ″ PanelsSupport for Custom Handles Tools and materials requiredDoor using at least 2 screws Reinstall original screws into the door extrusionZKHR1 Trim Kit For 1/4″ Panels Locate handle positionZKTR36LH/ZKTR36RH Trim Kit ″ Custom PanelsInstall panels Back Side Custom PanelInstall Handles Step AdjustGrille Panel heightGrille panel Install four of the six larger undercut screws so thatTop of the screws are 1/16″ from the surface ZKHTR1 Trim Kit For 3/4″ Panels Tools and materials requiredPart List BeforeTemporarily mount door panel LocatePosition AssembleMount assembled panel ZKHRSS1 Trim Kit For 1/4″ Panels Tubular Stainless Steel HandlesIf you are installing handle onto a Stainless Steel Panel Step Match handle extrusions to handleOn the back side of the panel-at the handle side Measure and mark 1/4″ below the top edgeDecorator Step Install standoffs onto handlesStep Install handles and panels Raised Panel on 1/4″ Thick Backing ZKHTRSS1 For 3/4″ Panels KitBefore you BeginUsing the Allen wrench provided. The standoff Match HandleTo Panel Should be tight against the handleUnified 3/4″ Custom Grille Panel Kit Step Install Spacer PadsZUG75 Trim Kit Step Level Both Products Roll Both Products into OpeningRefrigerator and freezer must be secured to prevent tipping Trim Strip Install CenterStep Remove Wire Fence and Switch Cover Step Install Grille Base Cover Remove Grille Frame Unified Base CoverStep Install Soffit Vent Top Secure Custom Panel To Support Removing side screws. Discard top piece, retainStep Adjust Door Alignment
Top Page Image Contents