GE ZIR36N RH Match Handle, To Panel, Using the Allen wrench provided. The standoff, Mounting

Page 34

ZKHTRSS1 (For 3/4″ Panels)

Tubular Stainless Steel Handles

Step 1	•Cut a piece of corrugated to use as a pad to protect
Match Handle	the panel finish. Additional material may be
Extrusion	required to protect flooring when drilling.
to Panel	•Place custom panel on the pad, appearance side
	down.
	•Select handle extrusion for your model, left or right
	side extrusion.
	•Place extrusion against the handle side of the panel.
	•Align the extrusion evenly with the top and bottom
	of the panel.
	•Tape the extrusion to the panel to prevent
	movement.
	•Center punch and drill 1/8″ pilot holes through the
	holes in the extrusion and into the panel.
	•Turn panel over. On the appearance side, use 9/32″
	bit to enlarge clearance hole.

Align Extrusion Even

With Panel

Back Side

Custom Panel

NOTE: Hole locations must be exact to accept handle standoff and handle assembly.

Step 2	•Place a handle standoff on each attachment post
Install	on the handle. Position the screw hole on the
Standoffs	standoff to point to the floor.
onto Handles	•Install set screws into the bottom of each standoff,
	using the Allen wrench provided. The standoff
	should be tight against the handle.

Step 3	•Start mounting screws through the extrusion and
Install	just through the custom panel.
Mounting	•Stand panel up on the hinge side and hold to
Screws	access the appearance side. Place handle against
and Handles	mounting screws on the appearance side, drive top
	screw from the back of the extrusion partially into
	the standoff.
	•Drive bottom screw partially into the standoff,
	and then drive remaining screws partially into
	standoffs. Alternate back to the top, driving screws
	until the handle is tight against the door.

Screw

Allen Wrench

Step 4	It is best that 2 people perform this step.
Install	•Place assembled panel onto the bottom door trim
Assembled	with support bracket tabs inserted into slots.
Panels	•Push and hold the panel back against the steel
	door with door handle extrusion flush to the
	handle side of the door.
	•Reinstall original screws into the door extrusion.
	•Open the door fully to stop.
	•Install screws at the top and hinge side.

34

Image 34

Contents Installation Instructions Contents INGDesign Information 36″ Refrigerators, FreezersWhen Installed into a corner Side By Side Installation Freezer RefrigeratorAdvance planning exterior appearance options Installation Between Base Wall CabinetsInstallation At End-of-Run ″ thick custom panels-Without trim kitsTrim kit ModelsAvailable DescriptionsCustom Panel Dimensions Clearances″ Panel Cut panels to size 35-1/16 Handles35 -1/16 Custom Door Panel DimensionsDimension a Unified Custom Grille Panel 71-3/8 Thick PanelCustom Door Panel Dimensions Using Standard Trim Trim ″ Side Panels Insert end23 5/16 Flooring InstallationMaterials Required Grounding the RefrigeratorStep Remove Packaging Water Line InstallStep Shut off the main water supplyIllustration B Step Install Side PanelsIllustration a ″ to 3/4″ Side Panels Leading edge of sideStep Secure LevelOr Freezer To SidesDoor panels Install 1/4″Power Step CheckAlignment Adjust DoorTemperature Controls Arrange InteriorTo change grille panel size Grille Panel Frame AdjustmentZGC2 Trim Kit PiecesSupport for Custom Handles Parts ListZKHR1 Trim Kit For 1/4 ″ Panels Tools and materials requiredZKHR1 Trim Kit For 1/4″ Panels Door using at least 2 screwsReinstall original screws into the door extrusion Locate handle positionZKTR36LH/ZKTR36RH Trim Kit ″ Custom PanelsInstall panels Back Side Custom PanelGrille Install Handles StepAdjust Panel heightTop of the screws are 1/16″ from the surface Install four of the six larger undercut screws so thatGrille panel Part List ZKHTR1 Trim Kit For 3/4″ PanelsTools and materials required BeforePosition Temporarily mount door panelLocate AssembleMount assembled panel ZKHRSS1 Trim Kit For 1/4″ Panels Tubular Stainless Steel HandlesOn the back side of the panel-at the handle side If you are installing handle onto a Stainless Steel PanelStep Match handle extrusions to handle Measure and mark 1/4″ below the top edgeStep Install handles and panels Step Install standoffs onto handlesDecorator Raised Panel on 1/4″ Thick Backing Before you ZKHTRSS1 For 3/4″ PanelsKit BeginTo Panel Using the Allen wrench provided. The standoffMatch Handle Should be tight against the handleZUG75 Trim Kit Step Install Spacer PadsUnified 3/4″ Custom Grille Panel Kit Refrigerator and freezer must be secured to prevent tipping Roll Both Products into OpeningStep Level Both Products Step Remove Wire Fence and Switch Cover Install CenterTrim Strip Step Install Grille Base Cover Remove Grille Frame Unified Base CoverStep Install Soffit Vent Top Secure Custom Panel To Support Removing side screws. Discard top piece, retainStep Adjust Door Alignment