GE ZIF36N LH Step Install standoffs onto handles, Step Install handles and panels, Decorator

Page 31

Step 3

Install standoffs onto handles

ZKHRSS1 Trim Kit (For 1/4″ Panels)

Tubular Stainless Steel Handles

•Place a handle standoff onto each attachment post along the handle. Position the set screw hole on the

standoff to point to the floor.
• Install set screws into the bottom of each standoff,	Screw
using the Allen wrench provided. The standoff	Screw
should be tight against the handle.	Allen Wrench
	Allen Wrench

Step 4

Install handles and panels

FOR CUSTOM

WOOD

PANELS

See Step 4A for stainless steel panels

•Slide panel into the door trim. Leave about 4″ of the panel exposed to allow room to install the handle extrusion.

•Place extrusion onto the back side of the panel, install mounting screws through the extrusion and just through the panel.

•Drive screw part way through the top standoff, then part way through the bottom standoff. Install remaining standoffs part way.

•Drive all screws until the handle is tight against the panel.

•Remove tape.

•Slide the assembled panel into the door trim until the extrusion fits firmly against the steel door. Reinstall original screws into the extrusion.

Screw

Decorator

Door Panel

Handle

31

Image 31

Contents Installation Instructions ING Contents36″ Refrigerators, Freezers Design InformationSide By Side Installation Freezer Refrigerator When Installed into a corner″ thick custom panels-Without trim kits Installation Between Base Wall CabinetsInstallation At End-of-Run Advance planning exterior appearance optionsDescriptions ModelsAvailable Trim kitClearances Custom Panel Dimensions35-1/16 Handles ″ Panel Cut panels to sizeUnified Custom Grille Panel 71-3/8 Thick Panel Custom Door Panel DimensionsDimension a 35 -1/16Custom Door Panel Dimensions Using Standard Trim Trim ″ Side Panels Insert end23 5/16 Grounding the Refrigerator InstallationMaterials Required FlooringStep Remove Packaging Shut off the main water supply InstallStep Water Line″ to 3/4″ Side Panels Leading edge of side Step Install Side PanelsIllustration a Illustration BTo Sides LevelOr Freezer Step SecureCheck Install 1/4″Power Step Door panelsArrange Interior Adjust DoorTemperature Controls AlignmentPieces Grille Panel Frame AdjustmentZGC2 Trim Kit To change grille panel sizeTools and materials required Parts ListZKHR1 Trim Kit For 1/4 ″ Panels Support for Custom HandlesLocate handle position Door using at least 2 screwsReinstall original screws into the door extrusion ZKHR1 Trim Kit For 1/4″ Panels″ Custom Panels ZKTR36LH/ZKTR36RH Trim KitBack Side Custom Panel Install panelsPanel height Install Handles StepAdjust GrilleTop of the screws are 1/16″ from the surface Install four of the six larger undercut screws so thatGrille panel Before ZKHTR1 Trim Kit For 3/4″ PanelsTools and materials required Part ListAssemble Temporarily mount door panelLocate PositionMount assembled panel Tubular Stainless Steel Handles ZKHRSS1 Trim Kit For 1/4″ PanelsMeasure and mark 1/4″ below the top edge If you are installing handle onto a Stainless Steel PanelStep Match handle extrusions to handle On the back side of the panel-at the handle sideStep Install handles and panels Step Install standoffs onto handlesDecorator Raised Panel on 1/4″ Thick Backing Begin ZKHTRSS1 For 3/4″ PanelsKit Before youShould be tight against the handle Using the Allen wrench provided. The standoffMatch Handle To PanelZUG75 Trim Kit Step Install Spacer PadsUnified 3/4″ Custom Grille Panel Kit Refrigerator and freezer must be secured to prevent tipping Roll Both Products into OpeningStep Level Both Products Step Remove Wire Fence and Switch Cover Install CenterTrim Strip Unified Base Cover Step Install Grille Base Cover Remove Grille FrameRemoving side screws. Discard top piece, retain Step Install Soffit Vent Top Secure Custom Panel To SupportStep Adjust Door Alignment