GE ZIF36N RH ZKHR1 Trim Kit For 1/4″ Panels, Locate handle position, Door using at least 2 screws

Page 21

Step 2 Locate handle position

ZKHR1 Trim Kit (For 1/4″ Panels)

Support for Custom Handles

3/4" Min.

1-1/2" Max.

• Slide custom panel into the door trim.	• Determine the desired location of the custom
• Temporarily secure the new handle extrusion to the	handle and mark centerlines of the screw holes.
door using at least 2 screws.	• Drill 1/16″ pilot hole through the panel until it starts
• The custom handles must be located 3/4″ to 1-1/2″	into the aluminum extrusion. This will mark the
from the edge of the extrusion.	matching location for drilling the clearance hole
	when assembling the handle, panel and extrusion.

Step 3 Assemble panel, extrusion and handle

Decorator

Door Panel

Handle

Screw

Decorator

ExtrusionDoor

Panel

3/4" Min.

1-1/2" Max.

•Remove the handle extrusion and custom panel.

•Drill 1/16″ pilot hole through extrusion.

•Drill clearance holes through the panel and extrusion.

•Assemble the door panel, extrusion and custom handle.

•Install screw(s) long enough to pass through the extrusion, door panel and into the handle.

•Slide the assembly into the door frame until the new extrusion fits firmly against the steel door.

•Reinstall original screws into the door extrusion.

21

Image 21

Contents Installation Instructions ING Contents36″ Refrigerators, Freezers Design InformationSide By Side Installation Freezer Refrigerator When Installed into a cornerInstallation At End-of-Run Installation Between Base Wall CabinetsAdvance planning exterior appearance options ″ thick custom panels-Without trim kitsAvailable ModelsTrim kit DescriptionsClearances Custom Panel Dimensions35-1/16 Handles ″ Panel Cut panels to sizeDimension a Custom Door Panel Dimensions35 -1/16 Unified Custom Grille Panel 71-3/8 Thick PanelCustom Door Panel Dimensions Using Standard Trim ″ Side Panels Insert end Trim23 5/16 Materials Required InstallationFlooring Grounding the RefrigeratorStep Remove Packaging Step InstallWater Line Shut off the main water supplyIllustration a Step Install Side PanelsIllustration B ″ to 3/4″ Side Panels Leading edge of sideOr Freezer LevelStep Secure To SidesPower Step Install 1/4″Door panels CheckTemperature Controls Adjust DoorAlignment Arrange InteriorZGC2 Trim Kit Grille Panel Frame AdjustmentTo change grille panel size PiecesZKHR1 Trim Kit For 1/4 ″ Panels Parts ListSupport for Custom Handles Tools and materials requiredReinstall original screws into the door extrusion Door using at least 2 screwsZKHR1 Trim Kit For 1/4″ Panels Locate handle position″ Custom Panels ZKTR36LH/ZKTR36RH Trim KitBack Side Custom Panel Install panelsAdjust Install Handles StepGrille Panel heightInstall four of the six larger undercut screws so that Top of the screws are 1/16″ from the surfaceGrille panel Tools and materials required ZKHTR1 Trim Kit For 3/4″ PanelsPart List BeforeLocate Temporarily mount door panelPosition AssembleMount assembled panel Tubular Stainless Steel Handles ZKHRSS1 Trim Kit For 1/4″ PanelsStep Match handle extrusions to handle If you are installing handle onto a Stainless Steel PanelOn the back side of the panel-at the handle side Measure and mark 1/4″ below the top edgeStep Install standoffs onto handles Step Install handles and panelsDecorator Raised Panel on 1/4″ Thick Backing Kit ZKHTRSS1 For 3/4″ PanelsBefore you BeginMatch Handle Using the Allen wrench provided. The standoffTo Panel Should be tight against the handleStep Install Spacer Pads ZUG75 Trim KitUnified 3/4″ Custom Grille Panel Kit Roll Both Products into Opening Refrigerator and freezer must be secured to prevent tippingStep Level Both Products Install Center Step Remove Wire Fence and Switch CoverTrim Strip Unified Base Cover Step Install Grille Base Cover Remove Grille FrameRemoving side screws. Discard top piece, retain Step Install Soffit Vent Top Secure Custom Panel To SupportStep Adjust Door Alignment