GE ZIF36N RH, ZIR36N LH ZKHRSS1 Trim Kit For 1/4″ Panels, Tubular Stainless Steel Handles

Page 29

ZKHRSS1 Trim Kit (For 1/4″ Panels)

 

Tubular Stainless Steel Handles

 

 

Right hand door swing models are illustrated in these

This kit provides for the installation of a Tubular

instructions. Follow these instructions for left hand

Stainless Steel handle on 1/4" thick decorator door

models.

panel. The door extrusions allow the handle to be

 

secured to the door structure, rather than to the

NOTE: It is best that 2 people install this kit.

custom panel.

 

•Select extrusion for your model, discard other

Tools and materials required:

extrusion.

•#2 Phillips screwdriver

•Drill and appropriate bits

• Custom door panel

A

 

• Safety glasses

B

• Center punch

• Masking tape

C

• Hammer

 

•Pencil

•1/2″ thick 12″ x 12″ min. piece of plywood to

protect floor when drilling

D

• For stainless steel panel, wear gloves to protect

E

against sharp edges.

Parts List:

F

 

A. Handle extrusion (for left hand models)

G

B. Handle extrusion (for right hand models)

H

C. Door handle

 

D. 6 Spacer rings (for Stainless Panels ONLY)

 

(4 required, 2 extra)

 

E. 4 Handle standoffs

 

F.6 Screws for mounting handle standoffs (4 required, 2 extra)

G.6 Set screws (4 required, 2 extra)

H.3/32″ Allen wrench for set screws

Step 1

• Open fresh food door to 90°. Remove the screws

Remove

from the full-length handle.

handle

• Retain screws, discard handle.

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Installation Instructions ING Contents36″ Refrigerators, Freezers Design InformationSide By Side Installation Freezer Refrigerator When Installed into a cornerInstallation At End-of-Run Installation Between Base Wall CabinetsAdvance planning exterior appearance options ″ thick custom panels-Without trim kitsAvailable ModelsTrim kit DescriptionsClearances Custom Panel Dimensions35-1/16 Handles ″ Panel Cut panels to sizeDimension a Custom Door Panel Dimensions35 -1/16 Unified Custom Grille Panel 71-3/8 Thick PanelCustom Door Panel Dimensions Using Standard Trim 23 5/16 ″ Side Panels Insert endTrim Materials Required InstallationFlooring Grounding the RefrigeratorStep Remove Packaging Step InstallWater Line Shut off the main water supplyIllustration a Step Install Side PanelsIllustration B ″ to 3/4″ Side Panels Leading edge of sideOr Freezer LevelStep Secure To SidesPower Step Install 1/4″Door panels CheckTemperature Controls Adjust DoorAlignment Arrange InteriorZGC2 Trim Kit Grille Panel Frame AdjustmentTo change grille panel size PiecesZKHR1 Trim Kit For 1/4 ″ Panels Parts ListSupport for Custom Handles Tools and materials requiredReinstall original screws into the door extrusion Door using at least 2 screwsZKHR1 Trim Kit For 1/4″ Panels Locate handle position″ Custom Panels ZKTR36LH/ZKTR36RH Trim KitBack Side Custom Panel Install panelsAdjust Install Handles StepGrille Panel heightGrille panel Install four of the six larger undercut screws so thatTop of the screws are 1/16″ from the surface Tools and materials required ZKHTR1 Trim Kit For 3/4″ PanelsPart List BeforeLocate Temporarily mount door panelPosition AssembleMount assembled panel Tubular Stainless Steel Handles ZKHRSS1 Trim Kit For 1/4″ PanelsStep Match handle extrusions to handle If you are installing handle onto a Stainless Steel PanelOn the back side of the panel-at the handle side Measure and mark 1/4″ below the top edgeDecorator Step Install standoffs onto handlesStep Install handles and panels Raised Panel on 1/4″ Thick Backing Kit ZKHTRSS1 For 3/4″ PanelsBefore you BeginMatch Handle Using the Allen wrench provided. The standoffTo Panel Should be tight against the handleUnified 3/4″ Custom Grille Panel Kit Step Install Spacer PadsZUG75 Trim Kit Step Level Both Products Roll Both Products into OpeningRefrigerator and freezer must be secured to prevent tipping Trim Strip Install CenterStep Remove Wire Fence and Switch Cover Unified Base Cover Step Install Grille Base Cover Remove Grille FrameRemoving side screws. Discard top piece, retain Step Install Soffit Vent Top Secure Custom Panel To SupportStep Adjust Door Alignment
Top Page Image Contents