GE ZIF36N LH, ZIR36N LH, ZIF36N RH Step Install Soffit Vent Top Secure Custom Panel To Support

Page 39

Step 9

Install

Soffit

Vent Top

Step 10

Secure

Custom Panel

To Support

ZUG75 Trim Kit

Unified 3/4″ Custom Grille Panel Kit

Slip Dust Gasket

Into Trim On One EndSlip Second Dust

Gasket Into Trim

• Separate the top and hinge side trim pieces by	Reinstall
removing side screws. Discard top piece, retain	Screws
screws.
• Install one end piece to unified top piece with
2 original screws.

•Slip end of rubber dust gasket into end of top unified piece and slide trim towards the center.

Engage the second piece of gasket and continue sliding trim until even with opposite ends.

•Reinstall end pieces to case trims. Push top piece up against soffit or to installation height. Tighten screws on both sides.

•Whenever possible, place a level on the top trim. Adjust side trims until entire grille frame is level.

•Secure the grille panel support to the back side of the 3/4″ thick custom panel with #6 screws. Be sure the lip of the support is over the top of the wood panel.

Panel Support

Overlaps Top

Back View

Grille Panel Support

•Install four of the six larger undercut screws so that the top of the screws are 1/16″ from the surface of the support.

1/16"

• Attach the assembled panel to the grille opening by inserting the four protruding screws into the brackets on each side.

NOTE: Use screws supplied with ZKTR36 Trim Kits.

39

Image 39

Contents Installation Instructions ING Contents36″ Refrigerators, Freezers Design InformationSide By Side Installation Freezer Refrigerator When Installed into a corner″ thick custom panels-Without trim kits Installation Between Base Wall CabinetsInstallation At End-of-Run Advance planning exterior appearance optionsDescriptions ModelsAvailable Trim kitClearances Custom Panel Dimensions35-1/16 Handles ″ Panel Cut panels to sizeUnified Custom Grille Panel 71-3/8 Thick Panel Custom Door Panel DimensionsDimension a 35 -1/16Custom Door Panel Dimensions Using Standard Trim ″ Side Panels Insert end Trim23 5/16 Grounding the Refrigerator InstallationMaterials Required FlooringStep Remove Packaging Shut off the main water supply InstallStep Water Line″ to 3/4″ Side Panels Leading edge of side Step Install Side PanelsIllustration a Illustration BTo Sides LevelOr Freezer Step SecureCheck Install 1/4″Power Step Door panelsArrange Interior Adjust DoorTemperature Controls AlignmentPieces Grille Panel Frame AdjustmentZGC2 Trim Kit To change grille panel sizeTools and materials required Parts ListZKHR1 Trim Kit For 1/4 ″ Panels Support for Custom HandlesLocate handle position Door using at least 2 screwsReinstall original screws into the door extrusion ZKHR1 Trim Kit For 1/4″ Panels″ Custom Panels ZKTR36LH/ZKTR36RH Trim KitBack Side Custom Panel Install panelsPanel height Install Handles StepAdjust GrilleInstall four of the six larger undercut screws so that Top of the screws are 1/16″ from the surfaceGrille panel Before ZKHTR1 Trim Kit For 3/4″ PanelsTools and materials required Part ListAssemble Temporarily mount door panelLocate PositionMount assembled panel Tubular Stainless Steel Handles ZKHRSS1 Trim Kit For 1/4″ PanelsMeasure and mark 1/4″ below the top edge If you are installing handle onto a Stainless Steel PanelStep Match handle extrusions to handle On the back side of the panel-at the handle sideStep Install standoffs onto handles Step Install handles and panelsDecorator Raised Panel on 1/4″ Thick Backing Begin ZKHTRSS1 For 3/4″ PanelsKit Before youShould be tight against the handle Using the Allen wrench provided. The standoffMatch Handle To PanelStep Install Spacer Pads ZUG75 Trim KitUnified 3/4″ Custom Grille Panel Kit Roll Both Products into Opening Refrigerator and freezer must be secured to prevent tippingStep Level Both Products Install Center Step Remove Wire Fence and Switch CoverTrim Strip Unified Base Cover Step Install Grille Base Cover Remove Grille FrameRemoving side screws. Discard top piece, retain Step Install Soffit Vent Top Secure Custom Panel To SupportStep Adjust Door Alignment