GE ZIF36N LH, ZIR36N LH, ZIF36N RH, ZIR36N RH Back Side Custom Panel, Install panels

Page 23

ZKTR36LH/ZKTR36RH Trim Kit

3/4″ Custom Panels

Step 2

• Attach the new 3/4″ trim pieces on the top, hinge

Install

side and bottom using original screws.

3/4″ trim

 

Step 3

• Position support bracket on the back side of the

Apply panel

custom panel, 14-5/16″from the hinge side. Secure

support

support bracket to panel with screws provided.

brackets

 

 

 

 

Back Side Custom Panel

Hinge

 

 

Support Bracket

 

 

Side

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

14-5/16"

 

 

 

 

 

 

 

 

Bottom Edge

 

 

 

 

 

 

 

 

 

 

 

Step 4 Install panels

•Place the 3/4″ thick panel on the bottom trim with support bracket tabs inserted into slots. Push the panel back against the steel door, flush with hinge side trim.

•Open the door fully.

•Carefully drill 4 starter holes using a small drill bit, through the backside of the trim at the top.

•Install original screws through the trim and into the panel to secure the panel to the door.

•Drill 6 starter holes through the hinge side and

4 through the bottom trim. Install original screws.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Installation Instructions ING Contents36″ Refrigerators, Freezers Design InformationSide By Side Installation Freezer Refrigerator When Installed into a corner″ thick custom panels-Without trim kits Installation Between Base Wall CabinetsInstallation At End-of-Run Advance planning exterior appearance optionsDescriptions ModelsAvailable Trim kitClearances Custom Panel Dimensions35-1/16 Handles ″ Panel Cut panels to sizeUnified Custom Grille Panel 71-3/8 Thick Panel Custom Door Panel DimensionsDimension a 35 -1/16Custom Door Panel Dimensions Using Standard Trim 23 5/16 ″ Side Panels Insert endTrim Grounding the Refrigerator InstallationMaterials Required FlooringStep Remove Packaging Shut off the main water supply InstallStep Water Line″ to 3/4″ Side Panels Leading edge of side Step Install Side PanelsIllustration a Illustration BTo Sides LevelOr Freezer Step SecureCheck Install 1/4″Power Step Door panelsArrange Interior Adjust DoorTemperature Controls AlignmentPieces Grille Panel Frame AdjustmentZGC2 Trim Kit To change grille panel sizeTools and materials required Parts ListZKHR1 Trim Kit For 1/4 ″ Panels Support for Custom HandlesLocate handle position Door using at least 2 screwsReinstall original screws into the door extrusion ZKHR1 Trim Kit For 1/4″ Panels″ Custom Panels ZKTR36LH/ZKTR36RH Trim KitBack Side Custom Panel Install panelsPanel height Install Handles StepAdjust GrilleGrille panel Install four of the six larger undercut screws so thatTop of the screws are 1/16″ from the surface Before ZKHTR1 Trim Kit For 3/4″ PanelsTools and materials required Part ListAssemble Temporarily mount door panelLocate PositionMount assembled panel Tubular Stainless Steel Handles ZKHRSS1 Trim Kit For 1/4″ PanelsMeasure and mark 1/4″ below the top edge If you are installing handle onto a Stainless Steel PanelStep Match handle extrusions to handle On the back side of the panel-at the handle sideDecorator Step Install standoffs onto handlesStep Install handles and panels Raised Panel on 1/4″ Thick Backing Begin ZKHTRSS1 For 3/4″ PanelsKit Before youShould be tight against the handle Using the Allen wrench provided. The standoffMatch Handle To PanelUnified 3/4″ Custom Grille Panel Kit Step Install Spacer PadsZUG75 Trim Kit Step Level Both Products Roll Both Products into OpeningRefrigerator and freezer must be secured to prevent tipping Trim Strip Install CenterStep Remove Wire Fence and Switch Cover Unified Base Cover Step Install Grille Base Cover Remove Grille FrameRemoving side screws. Discard top piece, retain Step Install Soffit Vent Top Secure Custom Panel To SupportStep Adjust Door Alignment
Top Page Image Contents