GE ZIF36N RH, ZIR36N LH, ZIR36N RH, ZIF36N LH installation instructions Step Remove Packaging

Page 13

Installation

36″ Refrigerators, Freezers

Step 1

Remove

Packaging

CAUTION

Refrigerator and freezer is much heavier at the top than at the bottom – be careful when moving. When using a hand truck, handle from side only.

PRUDENCE

Le réfrigérateur est beaucoup plus lourd en haut qu'en bas. Il faut être prudent lors des déplacements. Si un diable est utilisé, il faut soulever le réfrigérateur sur le côté seulement.

•Remove outer carton.

–Carefully cut banding at the top and bottom.

•Slide out back corner posts (2).

•Slide carton off top of cabinet.

NOTE: IT IS NOT NECESSARY TO LAY CABINET DOWN IN ORDER TO REMOVE SKID!

7/16" Bolt

•Lift the refrigerator off the skid with an appliance dolly. Handle from the sides.

•The unit is secured to the skid with 4 slotted tie- down straps. First remove the 5/16″ bolts from the

base channels in the tie-downs, then remove the 7/16″ bolts securing the straps to the skid.

•Protect the flooring. Cut a large piece of the cardboard carton and place under the product.

•Support blocks on the bottom must be removed before the refrigerator is taken off the skid or damage will occur. Remove support blocks by carefully tilting cabinet to side and sliding out.

CAUTION

DO NOT ATTEMPT TO ROLL UNIT OFF SKID.

PRUDENCE

IL NE FAUT PAS ESSAYER DE FAIRE ROULER LE RÉFRIGÉRATEUR POUR L'ENLEVER DE LAY PALETTE.

13

Image 13

Contents Installation Instructions ING Contents36″ Refrigerators, Freezers Design InformationSide By Side Installation Freezer Refrigerator When Installed into a cornerInstallation At End-of-Run Installation Between Base Wall CabinetsAdvance planning exterior appearance options ″ thick custom panels-Without trim kitsAvailable ModelsTrim kit DescriptionsClearances Custom Panel Dimensions35-1/16 Handles ″ Panel Cut panels to sizeDimension a Custom Door Panel Dimensions35 -1/16 Unified Custom Grille Panel 71-3/8 Thick PanelCustom Door Panel Dimensions Using Standard Trim Trim ″ Side Panels Insert end23 5/16 Materials Required InstallationFlooring Grounding the RefrigeratorStep Remove Packaging Step InstallWater Line Shut off the main water supplyIllustration a Step Install Side PanelsIllustration B ″ to 3/4″ Side Panels Leading edge of sideOr Freezer LevelStep Secure To SidesPower Step Install 1/4″Door panels CheckTemperature Controls Adjust DoorAlignment Arrange InteriorZGC2 Trim Kit Grille Panel Frame AdjustmentTo change grille panel size PiecesZKHR1 Trim Kit For 1/4 ″ Panels Parts ListSupport for Custom Handles Tools and materials requiredReinstall original screws into the door extrusion Door using at least 2 screwsZKHR1 Trim Kit For 1/4″ Panels Locate handle position″ Custom Panels ZKTR36LH/ZKTR36RH Trim KitBack Side Custom Panel Install panelsAdjust Install Handles StepGrille Panel heightTop of the screws are 1/16″ from the surface Install four of the six larger undercut screws so thatGrille panel Tools and materials required ZKHTR1 Trim Kit For 3/4″ PanelsPart List BeforeLocate Temporarily mount door panelPosition AssembleMount assembled panel Tubular Stainless Steel Handles ZKHRSS1 Trim Kit For 1/4″ PanelsStep Match handle extrusions to handle If you are installing handle onto a Stainless Steel PanelOn the back side of the panel-at the handle side Measure and mark 1/4″ below the top edgeStep Install handles and panels Step Install standoffs onto handlesDecorator Raised Panel on 1/4″ Thick Backing Kit ZKHTRSS1 For 3/4″ PanelsBefore you BeginMatch Handle Using the Allen wrench provided. The standoffTo Panel Should be tight against the handleZUG75 Trim Kit Step Install Spacer PadsUnified 3/4″ Custom Grille Panel Kit Refrigerator and freezer must be secured to prevent tipping Roll Both Products into OpeningStep Level Both Products Step Remove Wire Fence and Switch Cover Install CenterTrim Strip Unified Base Cover Step Install Grille Base Cover Remove Grille FrameRemoving side screws. Discard top piece, retain Step Install Soffit Vent Top Secure Custom Panel To SupportStep Adjust Door Alignment