GE ZIF36N RH, ZIR36N LH Install Center, Trim Strip, Step Remove Wire Fence and Switch Cover

Page 37

ZUG75 Trim Kit

Unified 3/4″ Custom Grille Panel Kit

Step 4	NOTE: This step can be used
Secure	as an alternative to Step 2,
Products	Anti-Tip bracket installation,
To Sides	whenever brackets cannot
	be used. Whenever possible,
	perform this step for additional
	anti-tip security.

When using 1/2″ to 3/4″ thick side panels, the front flange of the case trim is attached to the side panel.

•Open door to access case trim.

•Drill hole in trim slightly below the interior opening.

•Drive screw through the trim and into the side panel.

•Follow the same procedure on the opposite outside product trim.

	Refrigerator
Stud	Cabinet
	Door
	Spacer
	Block
OR

If the product is installed between cabinets with no side panels or into a custom enclosure, install a spacer block as shown.

Step 5	• Open doors fully.
Install Center	• Starting at the top, press trim strip over inside case
Trim Strip	trims of both products.
	• Continue pressing trim until you reach the bottom
	of the case trims. The trim will align with the top
	and bottom of the case trim.

Step 6

Remove Wire Fence and Switch Cover

Case Trim

U-Shape

Trim

Remove

3Screws

•Remove 3 screws holding the wire fence on both products. Retain fences and all screws.

Grill Base Cover

• Lift off grille base covers. Discard covers.

37

Image 37

Contents Installation Instructions ING Contents36″ Refrigerators, Freezers Design InformationSide By Side Installation Freezer Refrigerator When Installed into a cornerInstallation At End-of-Run Installation Between Base Wall CabinetsAdvance planning exterior appearance options ″ thick custom panels-Without trim kitsAvailable ModelsTrim kit DescriptionsClearances Custom Panel Dimensions35-1/16 Handles ″ Panel Cut panels to sizeDimension a Custom Door Panel Dimensions35 -1/16 Unified Custom Grille Panel 71-3/8 Thick PanelCustom Door Panel Dimensions Using Standard Trim Trim ″ Side Panels Insert end23 5/16 Materials Required InstallationFlooring Grounding the RefrigeratorStep Remove Packaging Step InstallWater Line Shut off the main water supplyIllustration a Step Install Side PanelsIllustration B ″ to 3/4″ Side Panels Leading edge of sideOr Freezer LevelStep Secure To SidesPower Step Install 1/4″Door panels CheckTemperature Controls Adjust DoorAlignment Arrange InteriorZGC2 Trim Kit Grille Panel Frame AdjustmentTo change grille panel size PiecesZKHR1 Trim Kit For 1/4 ″ Panels Parts ListSupport for Custom Handles Tools and materials requiredReinstall original screws into the door extrusion Door using at least 2 screwsZKHR1 Trim Kit For 1/4″ Panels Locate handle position″ Custom Panels ZKTR36LH/ZKTR36RH Trim KitBack Side Custom Panel Install panelsAdjust Install Handles StepGrille Panel heightTop of the screws are 1/16″ from the surface Install four of the six larger undercut screws so thatGrille panel Tools and materials required ZKHTR1 Trim Kit For 3/4″ PanelsPart List BeforeLocate Temporarily mount door panelPosition AssembleMount assembled panel Tubular Stainless Steel Handles ZKHRSS1 Trim Kit For 1/4″ PanelsStep Match handle extrusions to handle If you are installing handle onto a Stainless Steel PanelOn the back side of the panel-at the handle side Measure and mark 1/4″ below the top edgeStep Install handles and panels Step Install standoffs onto handlesDecorator Raised Panel on 1/4″ Thick Backing Kit ZKHTRSS1 For 3/4″ PanelsBefore you BeginMatch Handle Using the Allen wrench provided. The standoffTo Panel Should be tight against the handleZUG75 Trim Kit Step Install Spacer PadsUnified 3/4″ Custom Grille Panel Kit Refrigerator and freezer must be secured to prevent tipping Roll Both Products into OpeningStep Level Both Products Step Remove Wire Fence and Switch Cover Install CenterTrim Strip Unified Base Cover Step Install Grille Base Cover Remove Grille FrameRemoving side screws. Discard top piece, retain Step Install Soffit Vent Top Secure Custom Panel To SupportStep Adjust Door Alignment